Whirlpool EKA 3282/2482-1 RE User guide

Brand: Whirlpool

Model: EKA 3282/2482-1 RE

Category: Hobs

Type: User guide

This manual is also suitable for

PRECAUTIONS AND GENERAL SUGGESTIONS PAGE

TABLE OF CONTENTS

DESCRIPTION OF THE HOB PAGE

BEFORE USING THE HOB PAGE

HOW TO USE THE HOB PAGE

COOKING HINTS PAGE

ENERGY SAVING HINTS PAGE

CLEANING AND MAINTENANCE PAGE

AFTER-SALES SERVICE PAGE

INSTALLATION PAGE

ELECTRICAL CONNECTION PAGE

To get full satisfaction from your glass ceramic hob, please read carefully your

instruction manual and keep it at hand for ready reference.

DESCRIPTION OF THE HOB

GLASS CERAMIC HOB WITH

FRAME

KU 947-1

1. Quick Star heater ø 180 mm, 1800W - 400V

2. Quick Star heater ø 180 mm, 1800W - 400V

3. Double radiant heater ø 210/120 mm,

2100/700W - 400V

4. Radiant heater ø 145 mm, 1200W - 400V

5. Pilot lamps for residual heat indication

EKA 3482-1 li

1. Double radiant heater 210/120 mm,

2100/700W - 400V

2. Double oval radiant heater ø 145/250 mm,

1800/1000W - 400V

3. Quick Star heater ø 145 mm, 1200W - 400V

4. Quick Star heater ø 180 mm, 1800W - 400V

5. Pilot lamps for residual heat indication

6. Left warming zone 120W

7. Touch control for warming zone”ON/OFF”

EKA 3482-1 re

1. Double radiant heater ø 210/120 mm,

2100/700W - 400V

2. Double oval radiant heater 145/250 mm,

1800/1000W - 400V

3. Quick Star heater ø 145 mm, 1200W - 400V

4. Quick Star heater ø 180 mm, 1800W - 400V

5. Pilot lamps for residual heat indication

6. Right warming zone 120W

7. Touch control for warming zone “ON/OFF”

GLASS CERAMIC HOBS WITHOUT

FRAME

EKI 3482-1 / EKB 3482/2481

1. Double radiant heater ø 210/120 mm,

2100/700W - 400V

2. Radiant heater ø 145 mm, 1200W - 400V

3. Quick Star heater ø 180 mm, 1700W - 400V

4. Quick Star heater ø 145 mm, 1200W - 400V

5. Pilot lamps for residual heat indication

KI 947-1

1. Quick Star heater ø 180 mm, 1800W - 400V

2. Quick Star heater ø 180 mm, 1800W - 400V

3. Double radiant heater ø 210/120 mm,

2100/700W - 400V

4. Radiant heater ø 145 mm, 1200W - 400V

5. Pilot lamps for residual heat indication

DESCRIPTION OF THE HOB

1. Packaging (plastic bags, polystyrene parts,

etc.) must be stored out of reach of children

as they are potentially dangerous.

2. The packing material is recyclable and is

marked with the recycling symbol .

3. Check that the hob is not damaged, broken

or cracked.

4. Please ensure that the installation and the

electrical connection have been carried out

by a qualified technician, following the

manufacturer’s instruction and in

compliance with local safety regulations.

5. Prior to discarding an old appliance,

disconnect it electrically and render it

inoperable.

BEFORE USING THE HOB

Warning: electrical shock hazard

1. Before any maintenance operation,

disconnect the electricity leading to the hob

at the main power supply. Failure to do so

could result in electrical shock or injury.

2. If the hob is cracked, do not operate it but

switch off electricity at the main supply and

then, contact the After-Sales Service.

3. The glass ceramic hob has a good

mechanical strenght and can withstand

small accidents, misuse, however, if some

objects should fall on the surface and

damage it, please do not use the hob but

disconnect it from the main supply and

contact the nearest Service Centre.

4. Do not use the glass ceramic hob as a

working surface.

5. Do not use plastic utensils or aluminium foil

container to cook food on the glass ceramic

hob.

6. Do not use pans with wet bases.

7. When the hob is in use the surface of the

cooking zone is very hot; keep children

away from it.

8. As overheated fats and oils can easily ignite,

do not leave frying food unattended.

9. Do not operate the cooking zones without

anything on them.

PRECAUTIONS AND GENERAL SUGGESTIONS

10. Do not let electric wires (i.e.: of small

household appliances) to come into

contact with hot parts of the hob.

11. Do not forget synthetic clothes, plastic

utensils or any other material which could

ignite on the hob.

12. Take care not to scratch the surface of the

hob with the bottom of pans.

13. For best cooking results, we recommend

the use of stainless steel pans with flat

bases.

The diameter of the base must be the same

or slightly greater than that of the cooking

zone.

14. Never sprinkle sugar or sweetened food

such as jam, jellies and juices on the hob.

Should it happen, please clean immediately

the hob thoroughly following the cleaning

instructions.

PRECAUTIONS AND GENERAL SUGGESTIONS

The cooking zones are circumscribed and visi-

ble on the hob surface. The cooking zones are

controlled by knobs marked 0 to 12 or 10, sit-

uated on your oven. Every number on the

knob corresponds to a specific temperature of

the cooking zone.

The four pilot lamps indicating residual heat

are located at the front of the hob between

the two front cooking zones. The location of

each pilot lamp corresponds to the zone it rep-

resents. A pilot lamp will remain lit as long as

its cooking zone is hot, turning OFF only when

the cooking zone is sufficiently cool.

You will find informations on the layout and

use of the controls in the Operating

Instructions booklet contained in the respective

oven or control panel.

HOW TO USE THE HOB

DUO COOKING ZONE

The second area of both duo cooking zone can

be switched ON by turning the correspondent

knob to the right, rotating it at the far end (be-

yond the position 12 or 10). Then you can

choose the desired position.

HOW TO USE THE HOB

WARMING ZONE TOUCH CONTROL

(For mod. EKA 3482-1 li and EKA

3482-1 re)

Cooking Zone/Platt’s heating zone

On the glass ceramic hob, there is four

cooking zones and one for platt’s heating.

Each cooking zone is provided with an energy

control on your oven front panel or on the

separate built-in control panel to turn ON/OFF

and regulate the temperature for the cooking

zone and on the glass ceramic panel there is

an electronic touch button to turn ON/OFF

your platt’s heating zone.

The operations of the controls on the oven and

on the built-in control panel are explained in

the instructions manual supplied with the

built-in oven or the built-in control panel.

How to operate the sensitive

touch control buttons for the

platt’s heating zone

The buttons are on the front side of the platt’s

heater zone.

To turn ON the heater, proceed as follow:

- push button A shown as symbol

- make sure that the red LED is turned ON (A1)

- immediately after, maximum 5 seconds, push

button B with the symbol , the B1 LED

will turn ON and the first LED will turn OFF.

As long as LED B1 is ON that means that your

heater is still ON.

- To turn OFF the heater, push on button C

with symbol .

Important !

We recommend to always maintain dry

the sensors zone to avoid any interference

in the electronics controlling the heater

which might turn OFF your heater.

When installing the ceramic hob with the

platt’s heater zone on the left, make sure that

the installation is flush with the built-in oven or

switch box on the right.

When installing the ceramic hob with the

platt’s heater zone on the right, make sure

that the installation is flush with the built-in

oven or switch box on the left.

HOW TO USE THE HOB

Display position Suitable for the following cooking

12 10 To boil water, cook “gnocchi”, soup

10-11 10 To fry potatoes and meat ex. goulash

9-10 9-10 To fry croquettes, filet, tender loin, cordon bleu

8-9 8-9 To roast beefsteaks, chops, meat-balls, fishcakes, browned onions

7-8 7-8 To roast liver, eggs, croquette

5-6 6-7 To boil potatoes and stews

4-5 5-6 To cook vegetables and meat stews

3-4 4-5 Flesh and fish

2-3 3-4 To prepare rice-milk

1-2 2-3 To heat already cooked food

1 1 For cream sauces, to melt butter, chocolate, jellies

0 0 Position “OFF”.

COOKING HINTS

1. The pans base must be the same or slightly

greater than that of the cooking zone -

never smaller.

2. Use only pans with thick flat bases.

3. Possibly use a cover. You can set a lower

power and save energy.

4. Boil vegetables, potatoes, etc. with a little

water to save energy.

5. Pressure pans help to save energy and are

quicker than traditional pans.

ENERGY SAVING HINTS

NO!

1. Use clean clothes or paper for domestic use,

liquid detergent, commercial products such

as Sidol for stainless steel, Stahlfix or Cera-

fix or the enclosed razor-blade scraper.

2. Do not use abrasive powder or detergent,

oven sprays, rust or stain removers,

bleaches, sponges with a rough abrasive

surface, steelwood pads.

3. Try to clean the hob when it is only slightly

soiled, ideally after each use when it is

lukewarm or cold.

4. Do not reheat burnt particles.

5. Encrusted food or fats are better removed

while still warm, using the glass scraper

supplied or razor blade.

6. Finish cleaning with Sidol for stainless steel

or Stahlfix.

7. Should any sugar fall on the hob, remove it

immediately as it may melt when it comes in

contact with the hot surface of the hob.

CLEANING AND MAINTENANCE

You have bought a high quality hob, manufac-

tured according to the most advanced

technologies. In case of faults, please check if

you have followed all the instructions and hints

given in this booklet. Most probably the fault is

minimum. If the fault is not mentioned in the

instructions and other causes have to be dis-

considered, i.e. wrong electrical connection,

our Service is at your disposal for a qualified

check.

When calling for Service, please state always:

- the type of fault

- model of your glass ceramic hob, indicated

on the rating plate

- service code number of your glass ceramic

hob

- your address and telephone number

AFTER-SALES SERVICE

Important hints

This appliance has been designed, built

and marketed in compliance with:

- the safety targets of the “Low Voltage”

EEC Directive 73/23;

- the protection requirements of the

“EMC” EEC Directive 89/336 amended by

EEC Directive 93/68.

It belongs to Class Y against fire-hazard

and may be installed near a column.

Conformity declaration

This appliance incorporates parts intended to

come into contact with foodstuffs in compli-

ance with the Directive 89/109/EEC.

The hob may be installed in a structure with a

flat surface from 30 to 50 mm.

INSTALLATION

ASSEMBLY

GLASS CERAMIC HOBS WITH

FRAME

1- Installation of the hob on stainless steel

working area

Tools required:

- electric scisor, or profils cutter, eventually

frame saw, ripping saw with speed regulation,

if possible metal saw

- coverage ribbon

- angle plate with measuring possibilty

- eventually, liquid refrigerant

INSTALLATION

KU 947

EKA 3482

- Locate properly the hole position that you

should make +/- 0.5 mm

- The frame of the hob should be able to rest

properly on the main top; therefore make

sure the opening is properly centered.

- Cover the opening sides with the ribbon to

protect the hob frame scratches.

- Brush with oil the cutted parts.

- Make a hole of ø 10-12 mm on each of the

4 internal angles.

- Cut with hand saw if you can not introduce

electric saw.

- Please use the saw with caution in order not

to damage the stainless steel surface, which

shall be difficult to fix if damaged.

After you finished with preparing the hob

opening hole, please make sure that the an-

gles, borders and surface are clean and

smooth.

- Insert under the steel border the wooden

pieces supplied with the hob, that should en-

able you to make a 30 to 50 mm thik border

frame.

- Under the stainless steel frame of the hob,

there is a rubber self adhesive gasket; to level

eventually any irregularity use mastic sealing.

Please dont use silicone, to avoid any prob-

lem in case you need to disassemble the hob

later.

- Introduce the hob, center it properly in order

all sides cover the openings.

- Screw and thigten the hob to the working

surface from under the hob as instructed

above and hereafter.

INSTALLATION

2 - Installation on stone or wood

working table

Make an opening in the worktop following the

dimensions, in millimeters, indicated in:

- Fig. 1A, for glass ceramic hob mod. KU 947-1

- Fig. 1B, for glass ceramic hob mod. EKA

3482-1 li and EKA 3482-1 re.

The dimensions of the hob are indicated in the

respective figures. The distance between the

lower side of the glass-ceramic hob and the

cupboard of the wooden separation panel

must be at least 60 mm.

For practical and easy handling (long-handled

pans, etc.) we suggest to leave a distance of at

least 60 mm between the edges of the built-in

cooktop and any cupboards placed side-by-

side.

- Insert the glass ceramic hob into the

worktop’s opening from above, with the

signs on the front.

The fixing brackets (see Fig. 2) must be in po-

sition T (transport).

- Place the cooktop in the center and fix it with

the special brackets as indicated in Fig. 3.

Place the brackets in position M (assembly)

and screw them to the worktop with a

screwdriver.

If the worktop is 50 mm thick turn the brack-

ets 180° (Fig. 4).

INSTALLATION

Fig. 2

Fig. 3

Fig. 4

GLASS CERAMIC HOBS WITHOUT

FRAME (EKI 3482, KI 947)

1. Mounting on ready surface to

lean the hob

The leaning surface in the hole can be made

either by milling the borders in order to obtain

a leaning surface of 8.5 mm wide by 9 mm

high or by mounting 4 ledges to create a sup-

port frame for the hob as shown on Fig.1

INSTALLATION

Fig. 1

1.1 Preparation of the working

surface

Clean the hole from any dust or dirt.

- Brush 1 or 2 hands of special primer and dry

for about 30 minutes. This will protect the lean

surface against penetration of humidity and

shall increase the adherence of the bonding

material.

1.2 Mounting in a hole of the

working table prepared as per Fig.

1 above

Fix the autoadhesive washer on the cleaned

leaning area. In the angle zones and eventually

in the center of the leaning zone, fix 3-4 cms

strips of mastic sealing supplied at on interval

of about 10 cms from each other, then apply

strip of silicone high approx. 3-4 mm as per

Fig. 2.

With cleaning soap, clean properly the borders

of the hob to remove any oil grease or other

dirt from the hob borders.

Introduce in the hole the glass ceramic hob

and position it properly in the hole so as to

have equal distances all around.

Press slightly and evenly on the glass ceramic

hob top, specially on the angles sides, in order

to get the glass top levelled with the border of

the working table.

Attention: don’t use any tool against the

glass border.

INSTALLATION

Fig. 2

Mastic

Gasket

Silicone

2. Use of the metal lines support

(supplied)

The leaning area can be also prepared by

mounting the metal lines that the height can

be regulated by +/- 1.5 mm using the rotating

flat eccentric roller.

Prepare the holes respecting exactly the mea-

surements paying attention on the tolerances

indicated on Fig. 3.

INSTALLATION

Fig. 3

Page is loading ...

Whirlpool EKA 3282/2482-1 RE User guide

Brand: Whirlpool

Model: EKA 3282/2482-1 RE

Category: Hobs

Type: User guide

This manual is also suitable for

Download PDF

report

Whirlpool EKA 3282/2482-1 RE User guide

This manual is also suitable for

Whirlpool EKA 3282/2482-1 RE User guide

Related papers

Other documents