2. V-ZUG
  3. 326
326

V-ZUG 326 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the V-ZUG 326 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • Who should install the appliance?
    What should be done after installation to ensure safety?
    Where should the second identification plate be affixed?
    What is the required space beneath the appliance for good ventilation?
    Can an oven be installed beneath the appliance?
    What is the minimum depth of the work surface for installing an oven beneath the appliance?
    What type of isolating device should be provided in the house wiring system?
    Is it possible to install an oven beneath the appliance in the short mounting forms?
    What is the error message U400?
Installation instructions
Induction glass ceramic hob
With normal mounting frame
J326.113-1
20.1.09 ITH
1
These installation instructions apply to the model: 326 (GK36TIC)
Identification plate
The identification plate is next to the connection plate.
A Affix the second identification plate (enclosed) in an accessible position behind
the front of the fitted cabinet beneath the appliance.
A Information on the necessary mains voltage, type of current and fuse protection is to be obtained from the identification plate.
A The appliance is equipped with a mains cable that should be connected to a distribution box by the customer.
A If an oven is installed beneath the appliance, we recommend placing the distribution box behind the base. A cut-out can be made
in the rear wall for the cables.
Error message U400
The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order
specified.
Validity
General notes
If fitting in flammable material, the guidelines and standards for low voltage installations and for the fire protection must be strict-
ly observed.
Accessories
Designation Article no.
Ventilation protective plate set
For niche width 550–600 mm
H6.2122
Electrical connections
Electrical connections must be carried out by trained electricians in accordance with the guidelines and standards for low volt-
age installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. A
mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and socket
devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching are per-
missible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and fault-
free operation. After installation, live parts and cables with basic insulation must not be accessible. Old installations should al-
ways be checked.
Incorrect connection:
A pole conductor was connected to the connecting terminal for neutral conductors.
Quickly disconnect the appliance from the mains!
Connection plate
Identification plate
600/550
900
Installation pipe
Distribution box
Clamp
400 V 2N~
230 V~
AUS / NZ
PE/ green/yellow
N blue
L1 brown
L2 black
PE/ green/yellow
N blue
L1 brown
Installation instructions
Induction glass ceramic hob
With normal mounting frame
J326.113-1
20.1.09 ITH
2
Indications
䡲 The work surface has to be flat to ensure that the appliance is adequately
sealed against liquids.
䡲 In order to guarantee good ventilation, there needs to be a space of at
least 2 cm height beneath the appliance.
䡲 If the depth of the work surface is ≥30 mm, you can place an oven with
762 mm height directly underneath the appliance, exception: M-SL[P].
䡲 It is to possible install an oven in the short mounting forms 55-600, 60-600,
55-381 or 60-381 beneath the appliance if you use a ventilation grille set
(oven accessories).
Installing
1. Cut out mounting cut-out precisely.
2. Carefully place the appliance in the mounting cut-out and press against
the work surface with sufficient overlap.
Cool air supply if installed over a drawer or cabinet
In order to guarantee good ventilation, there needs to be a space of at least 2 cm height beneath the appliance.
With a protective plate beneath the ventilator
If necessary, a protective plate (see «Accessories») can be fitted above the drawer.
Installation
490 ±1
min. 50
min. 50
min. 30
600
560 ±1
600/550
900
514
584
52.6
from level
aim for
max. R10
min. 5
max. 75
==
min. 15
min. 55
min. 70
min. 30
600/550
900
==
min. 245 min. 245
Drawer Centre of ventilator
Air gap over the entire cabinet element width
min. 25 cm²
Necessary space for
the ventilation below
the worktop required
min. 5
==
~10
min. 70
52.6
15
Middle of angle
Drawer
Centre of fan
(17.4)
Warning:
Do not place mains
cable in the area of
the protective plate
Air gap over the entire cabinet element width
min. 25 cm²
/