2. Home
  3. Lighting
  4. Decorative lighting
  5. Howard
  6. VL50 Series

Howard VL50 Series, VL120 Series Installation Instructions Manual

  • I've reviewed the Installation Instructions for the VL Series LED Wallpack from Howard Lighting Products. This document provides detailed steps for installing the VL12X, VL20X, VL30X, VL40X, VL50X, VL80X, VL100X and VL120X models including safety precautions and wiring. I'm here to answer any questions you have about the installation process or the specifications outlined in this guide.
  • What should I do before installing the fixture?
    Who should perform the wiring?
    Where should this fixture be used?
    What do I need to do to avoid water damage?
INSTALLATION INSTRUCTIONS VL Series
Howard Lighting Products | 580 Eastview Drive | Laurel, MS 39443
(toll free) 800.956.3456 | (direct) 601.422.0033
www.HowardLightingProducts.com
Page 1 of 2
Rev: 11/7/2017
Versalite LED Wallpack
Applies to
VL12X, VL20X, VL30X, VL40X, VL50X, VL80X, VL100X, VL120X
Table 1: Product Specifications
Where X represents CCT (3=3000K, 4=4000K, 5=5000K)
SAFETY INSTRUCTION
● Read instructions carefully before attempting to install fixture. Retain instruction for future
reference.
● Disconnect power before installing or servicing. This fixture must be wired in accordance with the
National Electrical Code and applicable local codes and ordinances.
● All wiring should be performed by a qualified electrician. This fixture is for outdoor use and should
not be used in areas with limited ventilation or high ambient temperatures.
● Please consult product specifications (Table 1) before wiring to estimate total load.
INSTALLATION
1. Open the fixture 90° to get easy access to screws holding the back plate (figure 1). Loosen 2 screws
and take off the back plate.
Fig. 1
Fig. 2
2. Remove weep-hole screws from the bottom of the back plate (figure 2). VL12x series has only one
weep-hole screw in the bottom center.
Model
Dimensions
(LxWxH) inches
Input Voltage
Input Current
(Max.)
Power
Factor
Dimming
VL12X
6x5x3.4
100-277VAC
0.15A
≥0.9
NA
VL30X
9x7.6x4.5
0.38A
NA
VL40X
347-480VAC
0.17A
0-10V/PWM/VR
VL50X
100-277VAC
0.52A
NA
VL80X
13x11x5.5
1.0A
0-10V/PWM/VR
VL100X
277-480VAC
0.48A
0-10V/PWM/VR
VL120X
100-277VAC
1.5A
0-10V/PWM/VR
FIG.2
Weep-hole screws
INSTALLATION INSTRUCTIONS VL Series
Howard Lighting Products | 580 Eastview Drive | Laurel, MS 39443
(toll free) 800.956.3456 | (direct) 601.422.0033
www.HowardLightingProducts.com
Page 2 of 2
Rev: 11/7/2017
3. Tighten threaded coin plugs.
Fig. 3(a)
Fig. 3(b)
Fig. 3(c)
4. Orient so that the UP (↑) arrow points upwards (figure 3(a)). Secure the back plate to junction box
by screws (provided by others).
5. Apply silicone glue (provided by others) along the top and down both sides to prevent water
entering the back of the fixture. See figure 3(b) & 3(c).
6. Hang the fixture on the back plate. Connect the green ground wire with ring terminal to the back
plate (figure 4(a) & 4(b)). Using wire-nuts (provided by others) connect white to “Neutral”, black to
“Live”, and green to “Ground”.
FIG. 4(a)
FIG. 4(b)
FIG. 5
7. Close fixture and tighten the 2 screws (figure 5).
8. Adjust fixture to desired angle.
WARNING –
Water entering the fixture is likely to cause failure. Water damage due to loose coin plugs or
failure to seal the perimeter of the fixture to the mounting surface or failure to remove weep-
hole screws will void warranty.
FIG.2
/