2. Vehicles & accessories
  3. Motor vehicle accessories & components
  4. Motorcycle Accessories
  5. Sunlite
  6. 87753-SU
87753-SU

Sunlite 87753-SU User manual

  • Hello! I've reviewed the installation instructions for the Wall Pack Light. This document covers important safety information, step-by-step installation guidance, wiring details for both standard and dimmable setups, and basic maintenance advice. I'm ready to answer any questions you have about the installation process or the light's features.
  • What voltage range is supported by this light?
    How do I wire the light without a photocell?
    How do I wire the light with 0-10V dimming?
LIGHT
FIXTURE
(+)LINE BLACK
(-)COMMON WHITE
GROUND GREEN
LIGHT
FIXTURE
BLACK BLACK
(-)COMMON WHITE
GROUND GREEN
(+)LINE RED
WHITE
WALL PACK LIGHT INSTALLATION INSTRUCTIONS
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes.
Proper grounding is required for safety.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY
A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining fixture.
No user serviceable parts inside.
WIRING
Universal voltage driver permits operation at 100V to 277VAC, 50 or 60Hz except fixtures factory
ordered with a 120V photocell (/PC).
1. Connect the black fixture line to the (L) Live line supply wire.
2. Connect the white fixture line to the (N) Neutral line supply wire.
3. Connect the green fixture line to the (G) Ground line supply ground.
Without photocell With photocell
INSTALLATION
1. Open the lens assembly by unscrewing the two screws (Fig. 1).
2. Disconnect the wires between driver and LED module (Fig.1).
3. Prepare the back plate for mounting by drilling the appropriate holes (A). ( Fig. 2).
4. Line up the back plate in desired location and mount securely. (One gasket provided for weather-tight seal
between template and junction box). Pass before the wiring through the appropriate hole of the rear cover.
5. Complete the wiring to the power source and ground.
6. Reconnect the wires between driver and LED module.
7. Close the luminaire's door by tightening the screws (Fig. 1).
8. Caulk the entire perimeter of the luminaire to the mounting surface.
9. Apply power
Wall
Mounting screws
Screws Driver
Rear cover
Anchors
Gasket
LIGHT
FIXTURE
BLACK(+)LINE
(-)COMMON
(+)DIM V+
(-)DIM V-
GROUND
WHITE
PURPLE
GRAY
Vaux 12V
YELLOW
GROUND
WALL PACK LIGHT INSTALLATION INSTRUCTIONS
0-10V DIMMABLE WIRING
Universal voltage driver permits operation at 120V thru 277V,
50 or 60 Hz. For 0-10V Dimming, follow the wiring directions
as in fig. 4.
1. Connect the black fixture lead to the (+) LINE supply lead.
2. Connect the white fixture lead to the (-) COMMON supply lead.
3. Connect the GROUND wire from fixture to supply ground.
Do NOT connect the GROUND of the dimming fixture to the output.
4. Connect the purple fixture lead to the (V+) DIM lead.
5. Connect the gray fixture lead to the (V-) DIM lead.
6. Cap the yellow fixture lead, if present. Do NOT connect.
CLEANING & MAINTENANCE:
CAUTION: Be sure fixture temperature is cool enough to touch.
Do not clean or maintain whileFixture is energized.
1. Clean glass lens with non-abrasive glass cleaning solution.
2. Do not open fixture to clean the LED. Do not touch the LED.
TROUBLESHOOTING
1. Check that the line voltage at fixture is correct. Refer to wiring directions.
2.Is the fixture grounded properly?
Note: These instructions do not cover all details or variations in equipment nor do they provide for every
possible situation during installation, operation or maintenance.
Fig.1
WALL PACK LIGHT INSTALLATION INSTRUCTIONS
Fig.2
DIM-
LED- RDE
LED+
WHITE NEUTRAL
PURPLE
GRAY
BLUE
DIM+
BLACK LINE
MUST BE
GROUNDED
CASE
CCT Adajustable Switch
Power Adajustable Switch
DIM+
DIM-
3000K/4000K/5000K
LV1: 120W /80W
LV2: 100W /60W
LV3: 80W /40W
LV4: 60W /25W
234
334
290.6
170
Fig.3
CCT Adajustable Switch Power Adajustable Switch
CCT
Power 3000K /4000K/5000K (default: 5000K )
LV1:120W /LV2:100W /LV3:80W /LV4:60W(default: 120W )
Power
(80W) LV1:80W /LV2:60W /LV3:40W /LV4:25W (default: 80W )
(120W)
/