H3C S5820X-28S 24 SFP Installation guide

Brand: H3C

Model: S5820X-28S 24 SFP

Type: Installation guide

This manual is also suitable for

H3C LSW1FAN and LSW1BFAN

Installation Manual

Hangzhou H3C Technologies Co., Ltd.

Manual Version: 5W101-20090605

H3C Technologies Co., Ltd., a subsidiary of 3Com Corporation.

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

Care,

, TOP G, , IRF, NetPilot, Neocean, NeoVTL,

SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V

G, V

G, PSPT,

XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co.,

Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners.

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

About This Manual

Organization

H3C LSW1FAN and LSW1BFAN Installation Manual is organized as follows:

Chapter Contents

1 Fan Tray Overview Describes the fan tray and hardware specifications.

2 Removing/Installing a Fan Tray Describes removal and installation of the fan tray.

Appendix Appendix A: Obtaining Support for your Product.

Conventions

The manual uses the following conventions:

Convention Description

Means reader be extremely careful. Improper operation may cause

bodily injury.

Means reader be careful. Improper operation may cause data loss or

damage to equipment.

Means a complementary description.

Obtaining Documentation and Technical Support

To obtain up-to-date documentation and technical support, go to http://www.h3c.com and select your

country or region. Depending on your selection, you will be redirected to either of the following websites:

At http://www.h3c.com

Documentation

Go to the following columns for different categories of product documentation:

[Products & Solutions]: Provides information about products and technologies, as well as solutions.

[Technical Support & Document > Technical Documents]: Provides several categories of product

documentation, such as installation, configuration, and maintenance.

[Technical Support & Document > Software Download]: Provides the documentation released with the

software version.

Technical Support

customer_service@h3c.com

http://www.h3c.com

At http://www.h3cnetworks.com

Documentation

Select Drivers & Downloads in the Support area.

Select Documentation for Type of File and select Product Category.

Technical Support

Please see the appendix Obtaining Support for Your Product.

Documentation Feedback

You can e-mail your comments about product documentation to [email protected].

We appreciate your comments.

Environmental Protection

This product has been designed to comply with the requirements on environmental protection. For the

proper storage, use and disposal of this product, national laws and regulations must be observed.

Table of Contents

1 Fan Tray Overview·····································································································································1-1

LSW1FAN Overview and Specifications·································································································1-1

Introduction to LSW1FAN················································································································1-1

LSW1FAN Specifications ················································································································1-2

LSW1BFAN Introduction and Specifications ··························································································1-2

Introduction to LSW1BFAN·············································································································1-2

LSW1BFAN Specifications··············································································································1-3

Fan Tray Fail LEDs·································································································································1-3

2 Removing/Installing a Fan Tray ···············································································································2-1

Preparing Tools·······································································································································2-1

Removing a fan tray································································································································2-1

Installing a fan tray··································································································································2-3

Maintaining a Fan Tray ···························································································································2-5

1-1

1 Fan Tray Overview

The matrix between the two models of fan trays introduced in this manual and the Ethernet switches to

which they are applicable is as shown in

Table 1-1.

Table 1-1 Fan tray and device matrix

Fan tray Switch model

S5800-32F

S5810-50S

LSW1BFAN

S5820X-28S

S5800-60C-PWR

LSW1FAN

S5820X-28C

LSW1FAN Overview and Specifications

Introduction to LSW1FAN

An LSW1FAN fan tray comprises six independent fans (two big and four small fans). The two big fans

are used for heat dissipation of the main boards of the switch, and the four small fans are used for heat

dissipation of the OAP board and power supply units (PSUs).

The fan tray features hot swappable, low noise, and low power consumption, providing good heat

dissipation for the above-mentioned devices.

Figure 1-1 LSW1FAN view

(1): Fan tray handle (2): Captive screw

(3): 40 × 40 × 28 mm (1.57 × 1.57 × 1.1 in.) fans (4): 70 × 70 × 25.4 mm (2.76 × 2.76 × 1 in.) fans

1-2

LSW1FAN Specifications

Table 1-2 LSW1FAN specifications

Specification Description

Fan number

z Two 70 × 70 × 25.4 mm (2.76 × 2.76 × 1 in.) fans

z Four 40 × 40 × 28 mm (1.57 × 1.57 × 1.1 in.) fans

Fan speed

z 70 × 70 × 25.4 mm (2.76 × 2.76 × 1 in.) fans: 4700 R.P.M

z 40 × 40 × 28 mm (1.57 × 1.57 × 1.1 in.) fans: 9500 R.P.M

Max airflow 150 cubic feet per minute (CFM)

Input voltage 12 V

Total power consumption 15 W

Acoustics

Normal speed: 44.3 dB-A

Max speed: 54.1 dB-A

Operating temperature –10°C to +70°C (14°F to 158°F)

Relative humidity

(noncondensing)

5% to 90%

Storage temperature –40°C to +75°C (-40°F to +167°F)

Storage relative humidity

(noncondensing)

5% to 95%

LSW1BFAN Introduction and Specifications

Introduction to LSW1BFAN

An LSW1BFAN fan tray exhausts the air from the device making use of the rotation of the turbine,

providing more powerful airflows compared to common fans, and applicable to high-density devices.

The fan tray features small volume, fast heat dissipation, and hot swappable, providing powerful heat

dissipation for the above-mentioned devices.

1-3

Figure 1-2 LSW1BFAN view

(1): Captive screw (2): Air vent

(3): Fan tray handle (4): Captive screw

LSW1BFAN Specifications

Table 1-3 LSW1BFAN specifications

Specification Description

Fan number 1

Fan speed 5000 R.P.M

Max airflow 41.65 CFM

Input voltage 12 V

Power consumption 24 W

Acoustics

Normal speed: 48.4 dB-A

Max speed: 59.7 dB-A

Operating temperature –10°C to +60°C (14°F to 140°F)

Relative humidity (noncondensing) 5% to 90%

Storage temperature –40°C to +75°C (-40°F to +167°F)

Storage relative humidity

(noncondensing)

5% to 95%

Fan Tray Fail LEDs

The two models of fan trays do not have status LEDs. You can check the system status LED and the

seven-segment LED of the device installed with a fan tray to determine whether the fan tray operates

normally. If the fan tray fails, the two LEDs give an indication, as shown in

Table 1-4.

1-4

Table 1-4 Fan tray fail LEDs description

LED Mark State

System status LED SYS Steady red

Seven-segment LED Unit

The LED displays F for fan failure.

Only when the system status LED and the seven-segment LED are displayed as steady red and F

respectively does it indicate that a fan tray fails.

2-1

2 Removing/Installing a Fan Tray

z The LSW1FAN and LSW1BFAN fan trays are hot swappable, and therefore can be replaced with

the device running.

z The two models of fan trays and the devices are installed when shipped. This chapter mainly

introduces how to replace a fan tray when it fails.

The fan trays are hot swappable, and can be replaced with the device running. However, to prevent

overheating, do not operate the system without the fan trays for more than 2 minutes.

Preparing Tools

z Phillips screwdrivers

z ESD-preventive wrist strap

The installation tools are not provided with the Ethernet switches in this manual.

Removing a fan tray

1) Put on an ESD-preventive wrist strap, make sure that the wrist strap has a good skin contact and is

well grounded.

2) Loosen the screw on the fan tray with a Phillips screwdriver until the screw is completely separated

from the device, as shown in

Figure 2-1 and Figure 2-2.

2-2

Figure 2-1 Remove an LSW1FAN (1)

Figure 2-2 Remove an LSW1BFAN (1)

3) Holding the handle of the fan tray with one hand, pull part of the fan tray out. Then supporting the

bottom of the fan tray with the other hand, pull it straight out of the fan tray slot along the guide rails,

as shown in

Figure 2-3 and Figure 2-4.

To replace a fan tray with the device running, pull out the fan tray after it stop rotating. Keep your hands

away from the spinning fan blades even if the fan stops rotating; otherwise, the dynamic balance may

be broken, and thus the fan noise will be increased.

2-3

Figure 2-3 Remove an LSW1FAN (2)

Figure 2-4 Remove an LSW1BFAN (2)

After removing a fan tray, place it in an antistatic bag.

Installing a fan tray

1) Put on an ESD-preventive wrist strap, make sure that the wrist strap has a good skin contact and is

well grounded.

2) Take out the fan tray from the package, and make sure that the fan tray model matches the device

model.

3) Holding the handle of the fan tray with one hand and its bottom with the other hand, gently insert

the fan tray into the fan tray slot until the fan tray connector well touches the backplane, as shown

Figure 2-5 and Figure 2-6.

Figure 2-5 Install an LSW1FAN (1)

2-4

Figure 2-6 Install an LSW1BFAN (1)

4) Fasten the screws with a Phillips screwdriver until the fan tray is well seated in the chassis, as

shown in

Figure 2-7 and Figure 2-8.

Figure 2-7 Install an LSW1FAN (2)

Figure 2-8 Install an LSW1BFAN (2)

z To avoid damaging the connectors on a fan tray and backplane, slowly insert the fan tray. If you

feel hard when inserting the fan tray, plug out the fan tray and insert it again.

z If the captive screw cannot be tightly fixed, check the installation of the fan tray.

2-5

Maintaining a Fan Tray

To ensure normal operation and long service life of your fan trays, note the following when using fan

trays:

z Put on an ESD-preventive wrist strap and ensure a good skin contact.

z Adequate clearance is reserved at the air inlet/exhaust vents for ventilation.

z The rack or table/workbench has a good ventilation system.

A-1

Appendix A Obtaining Support for your Product

Warranty and other service benefits start from the date of purchase, so it is important to register your

product quickly to ensure you get full use of the warranty and other service benefits available to you.

Warranty and other service benefits are enabled through product registration. Register your product at

http://www.h3cnetworks.com, go to Support, Product Registration. Support services are based on

accounts that you create or have authorization to access. First time users must apply for a user name

and password that provides access to a number of eSupport features including Product Registration,

Repair Services, and Service Request. If you have trouble registering your product, please contact

3Com Global Services for assistance.

Purchase Value-Added Services

To enhance response times or extend warranty benefits, contact 3Com or your authorized reseller.

Value-added services like Express

and Guardian

can include 24x7 telephone technical support,

software upgrades, onsite assistance or advance hardware replacement. Experienced engineers are

available to manage your installation with minimal disruption to your network. Expert assessment and

implementation services are offered to fill resource gaps and ensure the success of your networking

projects. More information on 3Com maintenance and Professional Services is available at

http://www.h3cnetworks.com.

Contact your authorized reseller or 3Com for a complete list of the value-added services available in

your area.

Troubleshoot Online

You will find support tools posted on the web site at http://www.h3cnetworks.com/ under Support,

Knowledgebase. The Knowledgebase helps you troubleshoot H3C products. This query-based

interactive tool contains thousands of technical solutions.

Access Software Downloads

Software Updates are the bug fix / maintenance releases for the version of software initially purchased

with the product. In order to access these Software Updates you must first register your product on the

web site at http://www.h3cnetworks.com, go to Support, Product Registration.

First time users will need to apply for a user name and password. A link to software downloads can be

found at http://www.h3cnetworks.com, under Support, Drivers and downloads.

Software Upgrades are the software releases that follow the software version included with your

original product. In order to access upgrades and related documentation you must first purchase a

service contract from 3Com or your reseller.

Telephone Technical Support and Repair

To enable telephone support and other service benefits, you must first register your product at

http://www.h3cnetworks.com/

A-2

Warranty and other service benefits start from the date of purchase, so it is important to register your

product quickly to ensure you get full use of the warranty and other service benefits available to you.

When you contact 3Com for assistance, please have the following information ready:

z Product model name, part number, and serial number

z Proof of purchase, if you have not pre-registered your product

z A list of system hardware and software, including revision level

z Diagnostic error messages

z Details about recent configuration changes, if applicable

To send a product directly to 3Com for repair, you must first obtain a return authorization number (RMA).

Products sent to 3Com, without authorization numbers clearly marked on the outside of the package,

will be returned to the sender unopened, at the sender’s expense. If your product is registered and

under warranty, you can obtain an RMA number online at http://www.h3cnetworks.com under

support, Repair & Replacement Request. First time users will need to apply for a user name and

password.

3Com offers telephone, e-mail and internet access to technical support and repair services. To access

these services for your region, use the appropriate telephone number, URL or e-mail address.

Find a current directory of contact information posted on the web site at http://www.h3cnetworks.com

under Support, Technical Support Contact.

H3C S5820X-28S 24 SFP Installation guide

Brand: H3C

Model: S5820X-28S 24 SFP

Type: Installation guide

This manual is also suitable for

Download PDF

report

H3C S5820X-28S 24 SFP Installation guide

This manual is also suitable for

H3C S5820X-28S 24 SFP Installation guide

Related papers

Other documents