H3C H3C S5800-32F Installation guide

Brand: H3C

Model: H3C S5800-32F

Type: Installation guide

This manual is also suitable for

H3C S5800 Series Ethernet Switches

Installation Manual

Hangzhou H3C Technologies Co., Ltd.

Manual Version: 5W101-20090604

H3C Technologies Co., Ltd., a subsidiary of 3Com Corporation.

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

Care,

, TOP G, , IRF, NetPilot, Neocean, NeoVTL,

SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V

G, V

G, PSPT,

XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co.,

Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners.

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

About This Manual

Organization

H3C S5800 Series Ethernet Switches Installation Manual is organized as follows:

Chapter Contents

1 Product Overview

Briefly introduces the appearance, system description, as well as the

features and applications of the H3C S5800 series switches.

2 Installation Preparations

Describes the requirements on installation site, the safety

recommendations before and during installation, and the required

tools.

3 Installing a Switch

Covers the procedures for installing the H3C S5800 series, ground

wire connection, power module installation, interface module

installation, and so on.

4 Initial Power-On

Helps you get familiar with the basic knowledge of how to boot and

configure the H3C S5800 series, including device startup, power-on,

and initialization of system files, and so on.

5 Loading Software

Introduces how to loading application files and upgrading the Boot

ROM program by using the host software package.

6 Maintenance and

Troubleshooting

Introduces how to maintain software and hardware of the H3C S5800

series.

Appendix

Appendix A: Lightning protection of the H3C S5800 series switch.

Appendix B: Obtaining Support for your Product.

Conventions

The manual uses the following conventions:

GUI conventions

Convention Description

< > Button names are inside angle brackets. For example, click <OK>.

[ ]

Window names, menu items, data table and field names are inside

square brackets. For example, pop up the [New User] window.

Multi-level menus are separated by forward slashes. For example,

[File/Create/Folder].

Symbols

Convention Description

Means reader be extremely careful. Improper operation may cause

bodily injury.

Means reader be careful. Improper operation may cause data loss or

damage to equipment.

Means a complementary description.

Related Documentation

Manual Description

H3C PSR150-A & PSR150-D Power

Modules User Manual

Introduces the features, specifications, installation and

removal of the PSR150-A and PSR150-D power modules.

H3C PSR300-12A & PSR300-12D1

Power Modules User Manual

Introduces the features, specifications, installation and

removal of the PSR300-12A and PSR300-12D1 power

modules.

H3C PSR750-A & PSR750-D Power

Modules User Manual

Introduces the features, specifications, installation and

removal of the PSR750-A and PSR750-D power modules.

H3C S5820X & S5800 Series Ethernet

Switches Interface Cards User Manual

Introduces the types, appearance, installation and

removal of the interface cards used by the H3C S5820X

and S5800 series Ethernet switches.

H3C LSW148POEM Module User

Manual

Introduces the appearance and installation of the

LSW148POEM module.

H3C OAP Cards User Manual

Introduces the appearance, features and installation of the

OAP cards.

H3C LSW1FAN & LSW1BFAN

Installation Manual

Introduces the features, specifications, installation and

removal of the LSW1FAN and LSW1BFAN fan modules.

Obtaining Documentation and Technical Support

To obtain up-to-date documentation and technical support, go to http://www.h3c.com and select your

country or region. Depending on your selection, you will be redirected to either of the following websites:

At http://www.h3c.com

Documentation

Go to the following columns for different categories of product documentation:

[Products & Solutions]: Provides information about products and technologies, as well as solutions.

[Technical Support & Document > Technical Documents]: Provides several categories of product

documentation, such as installation, configuration, and maintenance.

[Technical Support & Document > Software Download]: Provides the documentation released with the

software version.

Technical Support

customer_service@h3c.com

http://www.h3c.com

At http://www.h3cnetworks.com

Documentation

Select Drivers & Downloads in the Support area.

Select Documentation for Type of File and select Product Category.

Technical Support

Please see the appendix Obtaining Support for Your Product.

Documentation Feedback

You can e-mail your comments about product documentation to [email protected].

We appreciate your comments.

Environmental Protection

This product has been designed to comply with the requirements on environmental protection. For the

proper storage, use and disposal of this product, national laws and regulations must be observed.

Table of Contents

1 Product Overview······································································································································1-1

Overview ·················································································································································1-1

S5800-60C-PWR ····································································································································1-4

Front Panel ······································································································································1-4

Rear Panel·······································································································································1-5

S5800-56C ··············································································································································1-6

Front Panel ······································································································································1-6

Rear Panel·······································································································································1-7

S5800-56C-PWR ····································································································································1-8

Front Panel ······································································································································1-8

Rear Panel·······································································································································1-8

S5800-32C ··············································································································································1-9

Front Panel ······································································································································1-9

Rear Panel·······································································································································1-9

S5800-32C-PWR ··································································································································1-10

Front Panel ····································································································································1-10

Rear Panel·····································································································································1-10

S5800-32F ············································································································································1-11

Front Panel ····································································································································1-11

Rear Panel·····································································································································1-12

Ports······················································································································································1-12

Console Port··································································································································1-12

Management Ethernet Port ···········································································································1-13

USB Interface ································································································································1-13

10/100/1000Base-T Ethernet Port·································································································1-13

100/1000Base-X SFP Interface·····································································································1-13

SFP+ Interface·······························································································································1-15

LEDs······················································································································································1-17

System Status LED ·······················································································································1-17

Hot Swappable Power Module Status LEDs·················································································1-18

RPS Status LED ····························································································································1-18

Port Mode LED ······························································································································1-19

Seven-Segment LED·····················································································································1-19

10/100/1000Base-T Auto-Sensing Ethernet Port Status LED·······················································1-20

100/1000Base-X SFP Interface Status LED ·················································································1-21

SFP+ Interface Status LED ···········································································································1-22

Management Ethernet Port Status LED ························································································1-22

OAP Card Status LED ···················································································································1-22

PoE Module Status LED················································································································1-23

Interface Card Status LED ············································································································1-23

Hot Swappable Power Modules············································································································1-23

Hot Swappable Fan Trays ····················································································································1-25

Interface Cards······································································································································1-26

OAP Card··············································································································································1-27

Hot Swappable PoE Module ·················································································································1-27

2 Installation Preparations···························································································································2-1

Safety Precautions ··································································································································2-1

Installation Site········································································································································2-1

Temperature/Humidity·····················································································································2-1

Cleanness········································································································································2-2

Electromagnetic Susceptibility·········································································································2-2

Laser Safety ····································································································································2-2

Installation Tools ·····································································································································2-3

3 Installing a Switch ·····································································································································3-1

Installation Flow of the Switch·················································································································3-2

Installing the Switch into a 19-Inch Rack Using Mounting Brackets·······················································3-2

Introduction to Mounting Brackets and Cable Management Brackets ············································3-3

Attaching the Mounting Brackets to a Switch··················································································3-4

Mounting the Switch to a Rack········································································································3-6

Mounting the Switch on a Workbench ····································································································3-7

Connecting the Ground Wire ··················································································································3-8

When a Grounding Strip is Available·······························································································3-8

Where a Grounding Conductor Can be Buried ·············································································3-10

In Other Installation Sites ··············································································································3-10

Installing a Power Module·····················································································································3-12

Installing the Power Module ··········································································································3-12

Removing the Power Module ········································································································3-14

Connecting the Power Cord··················································································································3-14

Connecting an AC Power Cord ·····································································································3-15

Connecting an RPS DC Power Cord·····························································································3-16

Connecting a Power Cord to the PSR150-A/PSR150-D·······························································3-18

Connecting a Power Cord to the PSR300-12A/PSR300-12D1·····················································3-19

Connecting a Power Cord to the PSR750-A&PSR750-D ·····························································3-21

Installing an Interface Card ···················································································································3-24

Installing an Interface Card ···········································································································3-24

Removing an Interface Card ·········································································································3-25

Installing an OAP Card··························································································································3-26

Installing an OAP Card to the Switch ····························································································3-26

Removing an OAP Card················································································································3-27

Installing a PoE Module ························································································································3-28

Installing a PoE Module·················································································································3-28

Removing the PoE module············································································································3-28

Verifying the Installation························································································································3-29

4 Initial Power-On ·········································································································································4-1

Setting Up the Configuration Environment······························································································4-1

Connecting the Console Cable ···············································································································4-1

Console Cable ·································································································································4-1

Connection Procedure·····················································································································4-2

Setting Terminal Parameters ··················································································································4-2

Booting the Switch ··································································································································4-5

iii

Checking Before Power-On·············································································································4-5

Powering On the Switch ··················································································································4-5

Changing the Boot Mode·················································································································4-7

5 Loading Software·······································································································································5-1

Introduction ·············································································································································5-1

Approaches for Loading Software···········································································································5-1

Loading Software Through the Boot ROM Menu····················································································5-2

Introduction to the Boot ROM Menu································································································5-2

Loading Software Using XMODEM Through Console Port·····························································5-4

Loading Software Using TFTP Through Ethernet Port ·································································5-11

Loading Software Using FTP Through Ethernet Port····································································5-15

Loading Software Through CLI ·············································································································5-18

Loading Software Through USB Interface·····················································································5-18

Loading Software Using FTP ········································································································5-19

Loading Software Using TFTP ······································································································5-20

6 Maintenance and Troubleshooting··········································································································6-1

Software Loading Failure ························································································································6-1

Password Loss········································································································································6-1

User Password Loss························································································································6-1

Boot ROM Password Loss ··············································································································6-1

Power Module Failure ·····························································································································6-2

Fixed Power Module Failure············································································································6-2

Hot Swappable Power Module Failure ····························································································6-3

OAP Card Failure····································································································································6-5

Hot Swappable PoE Module Failure ·······································································································6-5

Fan Failure ··············································································································································6-5

Fixed Fan Failure·····························································································································6-6

Hot Swappable Fan Tray Failure·····································································································6-6

Configuration Terminal Failure················································································································6-8

1-1

1 Product Overview

Overview

H3C S5800 Series Ethernet Switches (hereinafter referred to as the S5800 series) are Layer 3 Gigabit

Ethernet switching products developed by Hangzhou H3C Technologies Co., Ltd. (hereinafter referred

to as H3C). The S5800 series provide abundant service features. They provide the IPv6 forwarding

function and 10 GE uplink interfaces. Through H3C-specific cluster management, you can simplify

network management.

The S5800 series are designed as distribution or access devices for intranets and metropolitan area

networks (MANs). Supporting IPv4/IPv6 dual stack, the S5800 series provide abundant service

features and routing functions and can also be used for connecting server groups in data centers.

The S5800 series support the innovative Intelligent Resilient Framework (IRF) technology. With IRF,

multiple S5800 switches can be interconnected as a logical entity to form a new intelligent network

featuring high availability, scalability, and manageability.

The S5800 series support H3C Open Application Architecture (OAA) platform. To enable features such

as firewall, anti-virus, IPS, and wireless access control on the switches, you only need to insert OAP

cards into the switches and configure these features on the OAP cards.

The S5800 series include the following models, and have the system specifications as shown in

Table

1-1.

z S5800-60C-PWR

z S5800-56C

z S5800-56C-PWR

z S5800-32C

z S5800-32C-PWR

z S5800-32F

Table 1-1 The S5800 series system specifications

Item

S5800-60C-

PWR

S5800-56C

S5800-56C-

PWR

S5800-32C

S5800-32

C-PWR

S5800-3

Dimensions

(H × W × D)

86.1 × 440 ×

465 mm

(3.39 × 17.32

× 18.31 in.)

43.6 × 440 ×

367 mm

(1.72 ×

17.32 ×

14.45 in.)

43.6 × 440 ×

427 mm

(1.72 ×

17.32 ×

16.81 in.)

43.6 × 440 ×

367 mm

(1.72 ×

17.32 ×

14.45 in.)

43.6 × 440

× 427 mm

(1.72 ×

17.32 ×

16.81 in.)

43.6 ×

440 ×

427 mm

(1.72 ×

17.32 ×

16.81

in.)

Weight

18 kg

(39.68 lb)

6.5 kg

(14.33 lb)

8.5 kg

(18.74 lb)

6.0 kg

(13.23 lb)

8 kg

(17.64 lb)

8.5 kg

(18.74

lb)

1-2

Item

S5800-60C-

PWR

S5800-56C

S5800-56C-

PWR

S5800-32C

S5800-32

C-PWR

S5800-3

Console

port

z The console port of the S5800-60C-PWR, S5800-32C or S5800-32C-PWR is

available on the front panel.

z The console port of the S5800-56C, S5800-56C-PWR or S5800-32F is available

under the logo panel on the front panel.

Manageme

nt Ethernet

port

— — — — —

1, on the

rear

panel

USB

interface

1 (full speed)

z The USB interface of the S5800-60C-PWR, S5800-32C or S5800-32C-PWR is

available on the front panel.

z The USB interface of the S5800-56C, S5800-56C-PWR or S5800-32F is available

under the logo panel on the front panel.

10/100/100

0Base-T

Ethernet

ports

Supports

PoE

Supports

PoE

Supports

PoE

—

100/1000Ba

se-X SFP

interfaces

4 — — — — 24

SFP+

interfaces

—

4. You can plug an SFP+ transceiver, SFP transceiver or SFP+ cable

into the SFP interface. An SFP interface plugged in with an SFP+

cable can be used to connect IRF devices.

Number of

supported

interface

cards

2, on the front

panel

1, on the

rear panel

1, on the

rear panel

1, on the

rear panel

1, on the

rear panel

1, on the

front

panel

Interface

card models

supported

(optional)

LSW1SP4P0 (provides four 1 Gbps/10 Gbps SFP+ interfaces, which can be used to

connect IRF member devices)

LSW1SP2P0 (provides two 1 Gbps/10 Gbps SFP+ interfaces, which can be used to

connect IRF member devices)

LSW1GP16P0 (provides sixteen 1000 Mbps SFP interfaces)

LSW1GT16P (provides sixteen 1000 Mbps Ethernet electrical interfaces)

OAP card

IPS card

Firewall card

Access

controller

module

—

Hot

swappable

PoE module

LSW148POE

—

Fan

Hot

swappable

fan tray

(LSW1FAN)

Fixed fans Fixed fans Fixed fans Fixed fans

Hot

swappa

ble fan

tray

(LSW1B

FAN)

1-3

Item

S5800-60C-

PWR

S5800-56C

S5800-56C-

PWR

S5800-32C

S5800-32

C-PWR

S5800-3

Supported

hot

swappable

power

modules

PSR300-12A

PSR300-12D

PSR750-A

PSR750-D

— — — —

PSR150

-A

PSR150

-D

RPS power

module

supported

RPS1000-A3 RPS800-A

RPS1000-A

RPS800-A

RPS1000-

RPS800

-A

Rated voltage: 100 VAC to 240 VAC, 50/60 Hz

Max voltage: 90 VAC to 264 VAC, 47/63 Hz

Rated

voltage:

z 300 W

DC: –48

VDC to

–60 VDC

z 750 W

DC: –54

VDC to

–57 VDC

— — — —

Rated

voltage:

–48

VDC to

–60

VDC

Input

volta

RPS

Rated

voltage: –52

VDC to –55

VDC

Rated

voltage: 10.8

VDC to 13.2

VDC

Rated

voltage: –52

VDC to –55

VDC

Rated

voltage: 10.8

VDC to 13.2

VDC

Rated

voltage:

–52 VDC

to –55

VDC

Rated

voltage:

–52

VDC to

–55

VDC

Power

consumptio

DC: 94 W

AC: 96 W

102 W

DC: 107 W

AC: 131 W

67 W

DC: 64 W

AC: 85 W

DC: 58

AC: 67

Power

consumptio

n (full

configuratio

Single DC

output: 1840

W (1500 W

for PoE

output)

Dual DC

outputs: 1840

W (1500 W

for PoE

output)

Single AC

output: 714

W (425 W for

PoE output)

Dual AC

outputs: 1147

W (740 W for

PoE output)

163 W

DC: 973 W

(740 W for

PoE output)

AC: 673 W

(370 W for

PoE output)

105 W

DC: 870 W

(740 W for

PoE

output)

AC: 598 W

(370 W for

PoE

output)

DC: 136

AC: 146

Operating

temperature

0°C to 45°C (32°F to 113°F)

1-4

Item

S5800-60C-

PWR

S5800-56C

S5800-56C-

PWR

S5800-32C

S5800-32

C-PWR

S5800-3

Operating

humidity

(nonconden

sing)

10% to 90%

S5800-60C-PWR

Front Panel

Figure 1-1 S5800-60C-PWR front panel

(1) Interface card 1 (2) Interface card 2

(3) 10/100/1000Base-T auto-sensing Ethernet

port status LED

(4) Seven-segment LED

(5) Port mode LED (6) Console port

(7) USB interface (8) System status LED (SYS)

(9) Hot swappable power module 1 status LED

(PWR1)

(10) Hot swappable power module 2 status LED

(PWR2)

(11) OAP card status LED (SLOT3) (12) PoE module status LED (SLOT4)

(13) 100/1000Base-X SFP interface status LED (14) Port status LED mode switching button

(15) 100/1000Base-X SFP interface

(16) 10/100/1000Base-T auto-sensing Ethernet

port

z The S5800-60C-PWR provides two interface card slots on its front panel. Each slot is installed with

a filler panel when the switch is shipped. The above figure illustrates a switch with two

LSW1SP4P0 interface cards.

z You can select one or two interface cards for your switch as needed. See Interface Cards on page

1-26 for the interface card models supported by the S5800 series, and see Installing an Interface

Card

on page 3-24 for the installation of interface modules. See H3C S5820X & S5800 Series

Ethernet Switches Interface Cards User Manual for the detailed description of the interface

modules.

1-5

Rear Panel

Figure 1-2 S5800-60C-PWR rear panel

(1) OAP card filler panel (2) PoE module

(3) Grounding screw (4) Filler modules

(5) Hot swappable power module 1 (6) Hot swappable power module 2

(7) Hot swappable fan tray

z The S5800-60C-PWR provides two power module slots on its rear panel. Hot swappable power

module slot 1 is empty when the switch is shipped, and hot swappable power module 2 is installed

with a filler panel. The above figure illustrates a switch with two PSR300-12A AC power modules.

z You can select one or two power modules for your switch as needed. See Hot Swappable Power

Modules

on page 1-23 for the power module models supported by the S5800-60C-PWR, and see

Installing a Power Module on page 3-12 for the installation of power modules. See H3C

PSR300-12A & PSR300-12D1 Power Modules User Manual and H3C PSR750-A & PSR750-D

Power Modules User Manual for the detailed description of the power modules.

z The S5800-60C-PWR provides a PoE module slot on its real panel. The slot is installed with a filler

panel when the switch is shipped. You can install a PoE module on your switch as needed.

z The S5800-60C-PWR provides an OAP card slot on its rear panel. The slot is installed with a filler

panel when the switch is shipped. You can install an OAP card (firewall card, IPS card or access

controller module) on your switch as needed. For supported OAP card models, refer to

OAP Card

on page

1-27; for how to install an OAP card, refer to Installing an OAP Card on page 3-26.

1-6

S5800-56C

Front Panel

Figure 1-3 S5800-56C front panel

(1) 10/100/1000Base-T auto-sensing Ethernet

port

(2) 10/100/1000Base-T auto-sensing Ethernet port

status LED

(3) Seven-segment LED (4) Port mode LED

(5) SFP+ interface status LED

(6) Logo panel (A console port and a USB interface

are under this logo panel)

(7) System status LED (SYS) (8) RPS status LED (RPS)

(9) Interface card status LED (SLOT1) (10) SFP+ interface

(11) Port status LED mode switching button

To use the console port and USB interface, open the logo panel.

Figure 1-4 S5800-56C logo panel I

(1)

When opening or closing the logo panel, follow these steps to avoid damage to the logo panel:

z Insert your finger into the notch on the right side of the logo panel to open it. Do not try to open the

logo panel from any other parts.

z The logo panel is attached to the chassis through a rubber strip on its left. Swing the logo panel

within the elasticity of the rubber strip. Do not pull or swing the logo panel with excessive force;

otherwise, the rubber strip may fall off or be broken.

z Before pushing in the logo panel, make sure that the pin on the left of the logo panel is engaged

with the slot on the front panel. Then engage the tab on the right of the logo panel into the slot on

the chassis, and then press the logo panel until the tab clicks into the slot. If the tab is not engaged

into the slot, do not press the logo panel with excessive force to avoid damage to the tab.

1-7

Figure 1-5 S5800-56C logo panel II

(1) Tab of the logo panel (2) Pin of the logo panel

(3) Console port (4) USB interface

(5) Slot on the front panel (6) Rubber strip

Rear Panel

Figure 1-6 S5800-56C rear panel

(1) Bail latch (2) RPS receptacle protective cover

(3) Grounding screw (4) Interface card

(5) AC receptacle

z The S5800-56C provides one interface card slot on its rear panel. The slot is installed with a filler

panel when the switch is shipped. The above figure illustrates a switch with one LSW1SP4P0

interface card.

z You can select an interface card for your switch as needed. See Interface Cards on page 1-26 for

the interface card models supported by the S5800 series, and see

Installing an Interface Card on

page

3-24 for the installation of interface modules. See H3C S5820X & S5800 Series Ethernet

Switches Interface Cards User Manual for the detailed description of the interface modules.

1-8

S5800-56C-PWR

Front Panel

Figure 1-7 S5800-56C-PWR front panel

(1) 10/100/1000Base-T auto-sensing Ethernet

port

(2) 10/100/1000Base-T auto-sensing Ethernet

port status LED

(3) Seven-segment LED (4) Port mode LED

(5) SFP+ interface status LED

(6) Logo panel (A console port and a USB

interface are under this logo panel)

(7) System status LED (SYS) (8) RPS status LED (RPS)

(9) Interface card status LED (SLOT1) (10) SFP+ interface

(11) Port status LED mode switching button

To use the console port and USB interface, open the logo panel, as shown in

Figure 1-4 and Figure 1-5.

Rear Panel

Figure 1-8 S5800-56C-PWR rear panel

(1) RPS receptacle (2) Bail latch

(3) Grounding screw (4) Interface card

(5) AC receptacle

z The S5800-56C-PWR provides one interface card slot on its rear panel. The slot is installed with a

filler panel when the switch is shipped. The above figure illustrates a switch with one LSW1SP4P0

interface card.

z You can select an interface card for your switch as needed. See Interface Cards on page 1-26 for

the interface card models supported by the S5800 series, and see

Installing an Interface Card on

page

3-24 for the installation of interface modules. See H3C S5820X & S5800 Series Ethernet

Switches Interface Cards User Manual for the detailed description of the interface modules.

1-9

S5800-32C

Front Panel

Figure 1-9 S5800-32C front panel

(1) 10/100/1000Base-T auto-sensing Ethernet

port

(2) 10/100/1000Base-T auto-sensing Ethernet

port status LED

(3) SFP+ interface status LED (4) Console port

(5) USB interface (6) Seven-segment LED

(7) Port mode LED (8) System status LED (SYS)

(9) RPS status LED (RPS) (10) Interface card status LED (SLOT1)

(11) Port status LED mode switching button (12) SFP+ interface

Rear Panel

Figure 1-10 S5800-32C rear panel

(1) Bail latch (2) RPS receptacle protective cover

(3) Grounding screw (4) Interface card

(5) AC receptacle

z The S5800-32C provides one interface card slot on its rear panel. The slot is installed with a filler

panel when the switch is shipped. The above figure illustrates a switch with one LSW1SP4P0

interface card.

z You can select an interface card for your switch as needed. See Interface Cards on page 1-26 for

the interface card models supported by the S5800 series, and see

Installing an Interface Card on

page

3-24 for the installation of interface modules. See H3C S5820X & S5800 Series Ethernet

Switches Interface Cards User Manual for the detailed description of the interface modules.

1-10

S5800-32C-PWR

Front Panel

Figure 1-11 S5800-32C-PWR front panel

(1) 10/100/1000Base-T auto-sensing Ethernet

port

(2) 10/100/1000Base-T auto-sensing Ethernet

port status LED

(3) SFP+ interface status LED (4) Console port

(5) USB interface (6) Seven-segment LED

(7) Port mode LED (8) System status LED (SYS)

(9) RPS status LED (RPS) (10) Interface card status LED (SLOT1)

(11) Port status LED mode switching button (12) SFP+ interface

Rear Panel

Figure 1-12 S5800-32C-PWR rear panel

(1) RPS receptacle (2) Bail latch

(3) Grounding screw (4) Interface card

(5) AC receptacle

z The S5800-32C-PWR provides one interface card slot on its rear panel. The slot is installed with a

filler panel when the switch is shipped. The above figure illustrates a switch with one LSW1SP4P0

interface card.

z You can select an interface card for your switch as needed. See Interface Cards on page 1-26 for

the interface card models supported by the S5800 series, and see

Installing an Interface Card on

page

3-24 for the installation of interface modules. See H3C S5820X & S5800 Series Ethernet

Switches Interface Cards User Manual for the detailed description of the interface modules.

1-11

S5800-32F

Front Panel

Figure 1-13 S5800-32F front panel

(1) Interface card 1 (2) 100/1000Base-X SFP interface

(3) 10/100/1000Base-X SFP interface status

LED

(4) Seven-segment LED

(5) Port mode LED (6) SFP+ interface status LED

(7) Logo panel (A console port and a USB

interface are under this logo panel)

(8) System status LED (SYS)

(9) Hot swappable power module 1 status LED

(PWR1)

(10) Hot swappable power module 2 status LED

(PWR2)

(11) SFP+ interface (12) Port status LED mode switching button

To use the console port and USB interface, open the logo panel, as shown in

Figure 1-4 and Figure 1-5.

z The S5800-32F provides one interface card slots on its front panel. The slot is installed with a filler

panel when the switch is shipped. The above figure illustrates a switch with one LSW1SP4P0

interface card.

z You can select an interface card for your switch as needed. See Interface Cards on page 1-26 for

the interface card models supported by the S5800 series, and see

Installing an Interface Card on

page

3-24 for the installation of interface modules. See H3C S5820X & S5800 Series Ethernet

Switches Interface Cards User Manual for the detailed description of the interface modules.

1-12

Rear Panel

Figure 1-14 S5800-32F rear panel

(1) (2)

(3)

(5)(4)

(6)(7)

(1) Hot swappable power module 1 (2) Hot swappable power module 2

(3) Hot swappable fan tray (4) Management Ethernet port

(5) Grounding screw (6) Management Ethernet port ACT status LED

(7) Management Ethernet port LINK status LED

z The S5800-32F provides two power module slots on its rear panel. Hot swappable power module

slot 1 is empty when the switch is shipped, and hot swappable power module 2 is installed with a

filler panel. The above figure illustrates a switch with two PSR150-A AC power modules.

z You can select one or two power modules for your switch as needed. See Hot Swappable Power

Modules

on page 1-23 for the power module models supported by the S5800-32F, and see

Installing a Power Module on page 3-12 for the installation of power modules. See H3C PSR150-A

& PSR150-D Power Modules User Manual for the detailed description of the power modules.

Ports

Console Port

Each S5800 series provides one console port on the front panel. Table 1-2 describes the console port

specifications.

Table 1-2 Console port specifications

Item Specification

Connector type

RJ-45

Compliant standard

EIA/TIA-232

Transmission baud

rate

9600 bps to 115200 bps (defaulting to 9600 bps)

Service

z It can be connected to an ASCII terminal.

z It can be connected to a serial port of a local or remote (through a pair of

modems) PC running terminal emulation program.

Page is loading ...

H3C H3C S5800-32F Installation guide

Brand: H3C

Model: H3C S5800-32F

Type: Installation guide

This manual is also suitable for

Download PDF

report

H3C H3C S5800-32F Installation guide

This manual is also suitable for

H3C H3C S5800-32F Installation guide

Related papers

Other documents