H3C s5820x series Quick start guide

H3C S5820X Series Ethernet Switches

Quick Start

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 6PW108-20140516

licensors

No part of this manual may be reproduced or transmitted in any form or by

any means without prior written consent of Hangzhou H3C Technologies Co.,

Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H

3

Care, ,

IRF, NetPilot, Netflow, SecEngine, SecPath, SecCenter, SecBlade, Comware,

ITCMM and HUASAN are trademarks of Hangzhou H3C Technologies Co.,

Ltd.

All other trademarks that may be mentioned in this manual are the property of

their respective owners

Notice

The information in this document is subject to change without notice. Every

effort has been made in the preparation of this document to ensure accuracy

of the contents, but all statements, information, and recommendations in this

document do not constitute the warranty of any kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental protection

requirements. The storage, use, and disposal of this product must meet the

applicable national laws and regulations.

Preface

H3C S5820X Series Ethernet Switches Quick Start describes the installation of

the H3C S5820X series Ethernet switches.

This preface includes:

• Audience

• Conventions

• Obtaining documentation

• Technical support

• Documentation feedback

Audience

This documentation is intended for:

• Network planners

• Field technical support and servicing engineers

• Network administrators working with the S5820X series

Conventions

This section describes the conventions used in this documentation set.

Convention Descri

p

tion

WARNING

An alert that calls attention to important information that if not

understood or followed can result in personal injury.

CAUTION

An alert that calls attention to important information that if not

understood or followed can result in data loss, data

corruption, or damage to hardware or software.

IMPORTANT

An alert that calls attention to essential information.

NOTE

An alert that contains additional or supplementary

information.

Convention Descri

p

tion

TIP

An alert that provides helpful information.

Obtaining documentation

Access the most up-to-date H3C product documentation on the World Wide

Web at http://www.h3c.com

.

Click the links on the top navigation bar to obtain different categories of

product documentation:

[Technical Support & Documents > Technical Documents]

—Provides

hardware installation, software upgrading, and software feature

configuration and maintenance documentation.

[Products & Solutions]

—Provides information about products and

technologies, as well as solutions.

[Technical Support & Documents > Software Download]

—Provides the

documentation released with the software version.

Technical support

servi[email protected]

http://www.h3c.com

Documentation feedback

You can e-mail your comments about product documentation to

[email protected].

We appreciate your comments.

i

Contents

Overview ··········································································································· 1

About this guide ······························································································· 1

Product overview ······························································································ 1

Installation preparations ··················································································· 2

Installation site ·································································································· 2

Installation tools ································································································ 2

Installing the switch ··························································································· 3

Installation flow ································································································ 3

Installing the switch in a rack ········································································· 4

Attaching an ESD wrist strap ································································· 4

Installation accessories ··········································································· 4

Mounting positions ·················································································· 5

Installing an S5820X-26S switch in a 19-inch rack ···························· 7

Installing an S5820X-28C switch in a 19-inch rack ························· 10

Installing an S5820X-28S switch in a 19-inch rack ·························· 12

Mounting the switch on a workbench ·························································· 13

Connecting the grounding cable ·································································· 14

Connecting the grounding cable for an S5820X-26S switch ·········· 14

Connecting the grounding cable for an S5820X-28C or S5820X-28S

switch ······································································································ 15



Installing fan trays ·························································································· 17

Installing power modules ··············································································· 18

Connecting the power cord ·········································································· 21

Installing an interface card ··········································································· 25

Installing an OAP card ·················································································· 26

1

Overview

About this guide

This guide describes the basic installation procedures for the S5820X Switch

Series. For more information about the installation and configuration

procedures, system description, appearance, LEDs, software loading and

upgrading, and troubleshooting, see H3C S5820X Switch Series Installation

Guide.

Product overview

The H3C S5820X Switch Series includes the following models:

• S5820X-28S

• S5820X-28C

• S5820X-26S

NOTE:

The H3C S5820X Switch Series models and installation procedures mi

g

h

t

be updated without prior notice. For the latest quick start guide, go

to http://www.h3c.com

.

2

Installation preparations

Installation site

The switch must be used indoors. Before installation, verify that the rack is

sturdy enough to support the switch and its accessories.

To ensure correct operation and long service life of your switch, install it in an

environment that meets the temperature, humidity, and electromagnetic shield

(EMS) requirements. For more information, see H3C S5820X Switch Series

Installation Guide.

Installation tools

The installation tools are not provided with the switch. Prepare them yourself.

Figure 1 Installation tools

(1) ESD wrist strap (2)

Flat-blade screwdriver

(3) Phillips screwdriver (4) Marker

(5) Wrench (6)

Blow dryer

3

Installing the switch

Installation flow

Figure 2 Installation flow

NOTE:

The S5820X-28C switch supports hot-swapping of interface cards and

OAP cards. You can install or remove an interface card or an OAP card

w

hen the switch is operating. For more information, see "Installing an

interface card" and "Installing an OAP card."

4

Installing the switch in a rack

Attaching an ESD wrist strap

Before installation, wear an ESD strap, and make sure one end of the wrist

strap has a good skin contact and the other end is attached to a post of the

correctly-grounded rack, as shown in Figure 3.

Figure 3 Attaching an ESD wrist strap

Installation accessories

The S5820X-28S/S5820X-26S switch comes with a pair of 1 U load-bearing

mounting brackets. The S5820X-28C switch comes with a pair of 2 U

load-bearing mounting brackets, and each mounting bracket is attached with

a cable management bracket.

5

Figure 4 Mounting brackets

(1) 1 U mountin

g

brackets

(2) 2 U mounting brackets and cable management brackets

In addition to a pair of mounting brackets, the S5820X-26S switch also comes

with a pair of chassis rails and a pair of slide rails.

Figure 5 Chassis rail and slide rail

(1) Chassis rail (2) Slide rail

Mounting positions

The S5820X-28S and S5820X-28C switches provide three mounting positions:

one front mounting position (near the network ports), one mid-mounting

position, and one rear mounting position (near the power modules). Figure 6

sh

ows the mounting bracket installation positions on an S5820X-28S switch.

6

Figure 6 Mounting positions on an S5820X-28S switch

(1) Front mountin

g

position

(2) Mid-mountin

g

position

(3) Rear mounting position

The S5820X-26S switch provides two mounting positions: one front mounting

position (near the network ports) and one rear mounting position (near the

power modules), as shown in Figure 7.

Figure 7 M

ounting positions on an S5820X-26S switch

(1) Front mounting position

(2) Rear mountin

g

position

NOTE:

If a rack shelf is available, you can mount the switch in the rack by using

mounting brackets and a rack shelf. Put the switch on the rack shelf and

slide the switch to a position according to the mounting bracket installation

position. Then secure the switch to the rack.

7

Installing an S5820X-26S switch in a 19-inch

rack

Table 1 Installing an S5820X-26S switch in a 19-inch rack

Installation

p

rocedure

Remarks

Installation dia

g

ram

1. Attach the mounting

brackets to the

switch.

Required

• For mounting near the power

modules, see Figure 8.

• For mounting near the ports,

see Figure 9.

2. Attach chassis rails

to the switch.

Required

• For mounting near the ports,

see Figure 8.

• For mounting near the power

modules, see Figure 9.

3. Install cage nuts in

the rack posts.

Required See Figure 10.

4. Attach slide rails to

the rack posts.

Required See Figure 11.

5. Connect the

grounding cable to

the primary

grounding point.

Optional See Figure 12.

6. Install the switch in

the rack.

Required

See Figure 13.

This figure uses the

mounting position near the power

modules as an example.

NOTE:

• The depth of the rack must be a minimum of 1000 mm (39.37 in).

• The S5820X-26S switch has three grounding points, as shown in Fi

g

ure

19. The primary grounding point and auxiliary grounding point 1 are

on the right side panel. If you use one of these grounding points, you

must connect the grounding cable to the grounding point before you

mount the switch in the rack.

8

Figure 8 Installing the mounting brackets near the power modules and

installing the chassis rails

Figure 9 Installing the mounting brackets near the ports and installing the

chassis rails

Figure 10 Installing cage nuts in a rack post

9

Figure 11 Attaching slide rails to the rack

Figure 12 Connecting the grounding cable to the primary grounding point

(1) Groundin

g

si

g

n (2) Groundin

g

cable

10

Figure 13 Installing the switch in the rack (mounting brackets near the power

modules)

Installing an S5820X-28C switch in a 19-inch

rack

Table 2 Installing an S5820X-28C switch in a 19-inch rack

Installation

p

rocedure

Remarks

Installation dia

g

ram

1. Separate the mounting

brackets from cable

management brackets.

Optional See Figure 14.

2. Attach the mounting

brackets to the switch.

Required

• For mounting near the ports,

see Figure 14.

• For mounting in the mid-mounting

position, see Figure 14.

• For mounting near the power

modules, see Figure 14.

3. Install cage nuts in the

rack posts.

Required See Figure 10.

4. Install the switch in the

rack.

Required See Figure 15.

11

NOTE:

Before you install the mounting brackets in the mid-mounting position,

separate the mounting brackets from the cable management bracket.

Figure 14 Attaching mounting brackets to the S5820X-28C switch

(1) Separate the mountin

g

bracket from

the cable mana

g

ement bracket

(2) Install mountin

g

brackets near the ports

(3) Install mounting brackets in the mid-mounting position

(4) Install mountin

g

brackets near the power modules

1

2

3 4

12

Figure 15 Installing the switch in the rack

Installing an S5820X-28S switch in a 19-inch

rack

Table 3 Installing an S5820X-28S switch in a 19-inch rack

Installation

p

rocedure

Remarks

Installation dia

g

ram

1. Attach the mounting brackets to the

switch.

Required See Figure 16.

2. Install cage nuts in the rack posts.

Required See Figure 10.

3. Install the switch in the rack.

Required See Figure 17.

Figure 16 Attaching the mounting bracket to the switch

(1) Mountin

g

near the

ports

(2)

Mountin

g

in the mid-mountin

g

position

(3) Mounting near the power modules

13

Figure 17 Installing the switch in the rack

Mounting the switch on a workbench

CAUTION:

• Ensure 10 cm (3.94 in) of clearance around the switch.

• Do not place heavy objects on the switch.

If a standard 19-inch rack is not available, you can place you switch on a

workbench. The S5820X-26S switch cannot be mounted on a workbench.

To mount the switch on a workbench:

1. Make sure the workbench is clean and correctly grounded.

2. Place the switch with bottom up carefully, and clean the round holes on

the chassis bottom with dry cloth.

3. Attach the rubber feet to the four round holes in the chassis bottom.

4. Place the switch with upside up on the workbench.

14

Figure 18 Mounting the switch on a workbench

Connecting the grounding cable

CAUTION:

Correctly connecting the switch grounding cable is crucial to lightning

protection and EMS of a switch.

Connecting the grounding cable for an

S5820X-26S switch

The S5820X-26S switch has three grounding points, as shown in Figure 19.

H3C recommends that you use the primary grounding point.

Figure 19 Grounding points of the S5820X-26S switch

(1) Auxiliary grounding point 2 (2) Primary grounding point

(3)

A

uxiliary

g

roundin

g

point 1

To connect the grounding cable for an S5820X-26S switch:

15

1. Connect one end of the grounding cable to the grounding point on the

switch. See Figure 12.

2. Attach the oth

er end (ring terminal) of the grounding cable to a

grounding post on the grounding strip, and secure the grounding cable

to the grounding post by using a hex nut.

Figure 20 Connecting the grounding cable

Connecting the grounding cable for an

S5820X-28C or S5820X-28S switch

The S5820X-28C and S5820X-28S switches have a grounding point at their

rear panels. This guide uses the S5820X-28S switch as an example:

To connect the grounding cable:

1. Connect one end of the grounding cable to the grounding point of the

switch.

Page is loading ...

H3C s5820x series Quick start guide

H3C s5820x series Quick start guide

Related papers

Other documents