2. IKEA
  3. HOO 531 W
HOO 531 W

IKEA HOO 531 W, HOO 531 S Program Chart

  • Hello! I am an AI chatbot trained to assist you with the IKEA HOO 531 W Program Chart. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How far should the hob be from the extractor?
    How do I change the fuse in the plug?
    Can I use an alternative plug?
    How do I connect the wires in the mains lead?
    How do I remove and replace the grease filter?
    How do I mount or replace the carbon filter?
    How do I replace the bulbs?
HOO 521 - 531
5019 618 33000
INSTALLATION SHEET
Minimum distance from hob: 60 cm (electrical cookers), 70 cm
(gas, gas oil or coal cookers)
ELECTRICAL CONNECTION (ONLY FOR UK)
WARNING: THIS APPLIANCE MUST NOT BE EARTHED
THIS APPLIANCE IS DOUBLE INSULATED AND MUST NOT BE EARTHED.
The mains lead of this appliance is fitted with a BS 1363 13 amp fused plug.
To change a fuse in this type of plug use an A.S.T.A. approved fuse to BS1362 type.
1.
Remove the fuseholder and fuse.
2.
Fit replacement 13A fuse into fuseholder.
3.
Refit both into plug.
IMPORTANT:
The fuseholder must be refitted when changing a fuse and if the fuseholder is lost the plug must
not be used until a correct replacement is fitted.
Correct replacements are identified by the colour insert or the colour embossed in words on the base of the
plug.
Replacement fuseholders are available from your local Electricity Company Shop.
HOW TO CONNECT AN ALTERNATIVE PLUG
If the fitted plug is not suitable for your socket outlet, then it should be cut off and disposed of in order to avoid
a possible shock hazard should it be inserted into a 13A socket elsewhere.
A suitable alternative plug of at least 13 Amp rating e.g. 15 Amp round pin to BS 546 should then be fitted to
the cable.
The wires in this mains lead are coloured in accordance with the following code:-
BLUE  NEUTRAL - N
BROWN  LIVE - L
The BLUE wire must be connected to the terminal which is marked with the letter N or coloured black.
The BROWN wire must be connected to the terminal which is marked with the letter L or coloured red.
GB
61833000.fm5 Page 1 Tuesday, May 29, 2001 3:02 PM
5019 618 33000
HOO 521 - 531
61833000.fm5 Page 2 Tuesday, May 29, 2001 3:02 PM
5019 618 33000
HOO 521 - 531
1.
Control panel.
2.
Grease filter (inside the extractor grille).
3.
Light fixture.
4.
Steam deflector (pull-out).
Removing and replacing or cleaning the
grease filter
1.
Disconnect the electrical power supply.
2.
Pull out the stream deflector.
3.
Open the extractor grille (
Fig. A
).
4.
Remove the grease filter fixing device
(
Fig. B
).
5.
Remove the dirty grease filter.
6.
After replacing or cleaning the grease filter
(depends on model), remount in reverse order,
making sure the entire extraction surface is
covered.
Mounting or replacing the carbon filter
1.
Disconnect the electrical power supply.
2.
Pull out the steam deflector.
3.
Open the extractor grille (
Fig. A
).
4.
If a carbon filter is already mounted and needs
replacing, press the release buttons (
b
) and pull
the filter out downwards (
Fig. C
).
5.
If the filters are not mounted:
- fit the carbon filter onto the rings at the
rear (
a
);
- fix the carbon filter at the front by means of the
clips (
b
).
6.
Remount the extractor grille.
Replacing bulbs
1.
Disconnect the electrical power supply.
2.
Pull out the steam deflector.
3.
Open the extractor grille.
4.
Remove the burnt-out bulb.
Use 40 W max (E14) bulbs only.
5.
Remount the extractor grille.
CONTROL PANEL
A.
Light switch.
B.
Speed selector.
C.
Extractor power indicators.
C
Fig. A
Fig. B
Fig. C
small amount of steam
and fumes
medium amount of
steam and fumes
large amount of
steam
and fumes
PRODUCT DESCRIPTION SHEET
GB
61833000.fm5 Page 3 Tuesday, May 29, 2001 3:02 PM
5019 618 33000
HOO 521 - 531
NOTES
61833000.fm5 Page 4 Tuesday, May 29, 2001 3:02 PM
/