Whirlpool AKR 922 AL Program Chart

Brand: Whirlpool

Model: AKR 922 AL

Category: Cooker hoods

Type: Program Chart

Whirlpool AKR 922 AL is a range hood designed for efficient extraction of steam and fumes from your kitchen. It features three speed settings to accommodate different cooking conditions, from a small amount of steam to a large amount of steam and fumes. The hood also has a built-in light to illuminate your cooking surface, making it easier to see what you're cooking. With its sleek design and powerful performance, the Whirlpool AKR 922 AL is the perfect choice for any kitchen.

✂

5019 318

33021

AKR922

INSTALLATIONSANGABEN

Mindestabstand zur Kochfläche: 50 cm (Elektrokochplatten), 75 cm (Gas-, Öl-

oder Kohlekochplatten). Folgen Sie bei der Installation der Nummerierung

.....) und den jeweiligen Anleitungen. Schließen Sie das Gerät erst

nach erfolgter Installation an die Stromversorgung an.

INSTALLATION SHEET

Minimum height above cooker: 50 cm (electric cookers), 75 cm (gas, gas oil or

coal cookers). To assemble follow the numbers (1

.....) and relative

instructions. Do not connect the appliance to the electrical power supply until

installation is completed.

FICHE D'INSTALLATION

Distance minimale par rapport à la cuisinière : 50 cm (cuisinière électrique),

75 cm (cuisinière à gaz, mazout ou charbon). Pour le montage, suivez la

numérotation (1

.....) et les instructions correspondantes. Ne branchez

pas l'appareil tant que l'installation n'est pas terminée.

INSTALLATIEKAART

Minimumafstand tot het kooktoestel: 50 cm (elektrische kooktoestellen), 75 cm

(kooktoestellen op gas, olie of kolen). Volg voor de montage de nummering

.....) en de bijbehorende instructies. Sluit geen stroom aan op het

apparaat totdat de installatie geheel voltooid is.

FICHA DE INSTALACIÓN

Distancia mínima desde los quemadores: 50 cm (fuegos eléctricos), 75 cm

(fuegos de gas, gasóleo o carbón). Para efectuar el montaje siga la numeración

....) y las instrucciones. No enchufe el aparato hasta que su

instalación esté terminada.

FICHA DE INSTALAÇÃO

Distância mínima dos fogões: 50 cm (fogões eléctricos), 75 cm (fogões a gás,

óleo ou carbono). Para a montagem, siga a numeração (1

.....) e as

respectivas instruções. Não ligue o aparelho à corrente eléctrica até a instalação

estar concluída.

SCHEDA INSTALLAZIONE

Distanza minima dai fuochi: 50 cm (fuochi elettrici), 75 cm (fuochi a gas,

gasolio o carbone). Per il montaggio seguire la numerazione (1

.....) e le

istruzioni relative. Non dare corrente allapparecchio finchè linstallazione non è

totalmente completata.

ùüùü+ùùùþ

ü$12.)12.1. )2"0120"FP02!"0120"FP

0120".0! #02!0. #0! # +.22  21

.  #1202.!1





.2"1$02" /0"

2! 3 / 2020002!)!0*.21#10#!2  !&12"

0.212.1"

31833021.fm5 Page 1 Tuesday, November 27, 2001 8:57 AM

✂

AKR922

5019 318

33021

31833021.fm5 Page 2 Tuesday, November 27, 2001 8:57 AM

✂

5019 318

33021

AKR922

31833021.fm5 Page 3 Tuesday, November 27, 2001 8:57 AM

✂

AKR922

5019 318

33021

31833021.fm5 Page 4 Tuesday, November 27, 2001 8:57 AM

✂

5019 318

33021

AKR922

Preliminary information for installing the hood:

Expansion plugs are provided to secure the hood to most types of ceilings. A qualified technician is needed,

however, to make sure that the plugs are suitable for your ceiling. The ceiling must be strong enough to take

the weight of the hood.

Disconnect the power supply at the home main switch during electrical connections.

Adjust extension of the hood support structure, as the final height of the hood depends on this, and

remember that with installation completed the hood must be at least 50 cm above the cook-top in case

of electric cookers and 75 cm in case of gas or mixed cookers.

Fix the two sections of the structure using 8 screws.

Place the ceiling hole diagram directly above the cooktop (the centre of the diagram must match the

centre of the cooktop and the edges must be parallel to the sides of the cooktop - the side of the diagram

with the wording FRONT corresponds to the control panel side). Prepare the electrical connection.

Drill as shown (6 holes for 6 wall plugs - 4 plugs for hooking), screw the outer screws leaving a space of

about 1 cm between the screw head and the ceiling.

Fit an exhaust pipe inside the truss and connect it to the collar of the motor compartment (exhaust pipe

and clamps are not provided).

Hook the truss to the 4 screws (see step 4).

CAUTION! The side of the truss with connection box corresponds to the side of the control panel with

hood assembled.

Tighten the 4 screws.

Insert and tighten another 2 screws in the remaining free holes for secure fixing.

Carry out the electrical connection to the mains power supply, only turn on the power supply with

assembly completed.

10.

Hook the hood to the truss, check for perfect hooking - to hook the hood to the truss partially screw 4

screws (also see step 12).

11.

Fixing the hood to the truss with two screws, will also facilitate centering the two parts.

12.

Tighten the 4 screws fixing the truss to the hood.

13.

For extractor operation (

13A

), connect the other end of the exhaust pipe to the home drain device.

For filter operation (

13F

), fit deflector

on the truss and fix it with 4 screws to the special bracket.

Finally, connect the exhaust pipe to the collar located on the deflector.

14.

Fit the nuts with fixing hooks supplied inside

the top and bottom sections of the flues at the rectangular

slots. A total of 10 nuts must be fitted.

15.

Join the two top sections of the flue to cover the truss so that one of the slots on the sections is situated

on the same side of the control panel and the other on the opposite side.

Screw the two sections with 4 screws (2 each side - see the plan diagram for joining the two sections).

16.

Fix the top flue assembly to the truss, near the ceiling, with two screws (one each side).

17.

Carry out electrical connection of control panel and bulbs.

18.

Join the two bottom sections of the flue covering the truss using 6 screws (3 each side - also see the plan

diagram for joining the two sections).

19.

Insert the bottom section of the flue in the special seat to completely cover the motor compartment and

electrical connection box, and fix the hood with two screws from the inside.

20.

Apply the 2 tabs (supplied) to cover the fixing points of the bottom flue (CAUTION! THE BOTTOM FLUE

TABS ARE THE NARROWER AND SHALLOWER ONES).

The wider and deeper tabs are those used for the top flue, and must be cut to size.

21.

Turn the mains power on again at the central electrical panel and check for correct hood operation.

INSTALLATION - ASSEMBLY INSTRUCTIONS

IF NL E PGBD GR

31833021.fm5 Page 7 Tuesday, November 27, 2001 8:57 AM

✂

AKR922

5019 318

33021

To clean the grease filter:

Wash the grease filter at least once a month.

Disconnect the electrical power supply.

Remove the grease filters - Fig. 1: pull the spring

release handle (

) downwards, then remove the

filter.

After cleaning the grease filter refit in reverse order,

making sure the entire extraction surface is covered.

Replacing bulbs:

Disconnect the electrical power supply. Wait until

the bulbs have cooled down.

Use a small screwdriver or any other suitable tool to

prise off (

-Fig. 2) the lamp cover (

-Fig. 2).

Remove the burnt-out bulb.

Use 20 W max halogen bulbs only, making sure not

to touch them with your hand.

Close the lighting unit (snap-close).

Carbon filter Fitting and Maintenance:

Fitting the carbon filter:

Disconnect the electrical power supply.

Remove the grease filter (

- Fig. 1).

Remove the screw and then the filter holder

(

- Fig. 3).

Fit the carbon filter (

- Fig. 3) in the filter holder

(

- Fig. 3)

Refit the filter holder and secure it to the hood with

the screw (

- Fig. 3).

Refit the grease filter.

Carbon filter maintenance:

Unlike traditional carbon filters, this carbon filter can be

washed and reactivated. With normal hood use, the filter

should be cleaned once a month. The best way to clean

the filter is in a dishwasher at the highest temperature

possible, using a normal dishwasher detergent. To avoid

particles of food or dirt settling on the filter during

washing and giving rise to unpleasant smells, it is

advisable to wash the filter on its own. After washing,

dry the filter in the oven at 100° C for 10 minutes to

reactivate it. The filter will retain its odour-absorbing

capacity for three years, after which it will have to be

replaced.

CONTROL PANEL

Light ON/OFF switch.

ON/OFF and speed 1 selector switch

(small amount of steam and fumes).

Speed 2 selector switch

(medium amount of steam and fumes).

C+D.

Speed 3 selector switch

(large amount of steam and fumes).

FIG. 1

FIG. 2

FIG. 3

PRODUCT SHEET

Control panel

Grease filter

Grease

filter handle

Halogen bulbs

Steam deflector

Telescopic flue

Air outlet

(filter version)

IF NL E PGBD GR

31833021.fm5 Page 8 Tuesday, November 27, 2001 8:57 AM

Whirlpool AKR 922 AL Program Chart

Brand: Whirlpool

Model: AKR 922 AL

Category: Cooker hoods

Type: Program Chart

Download PDF

report

Whirlpool AKR 922 AL Program Chart

Whirlpool AKR 922 AL Program Chart

Related papers

Other documents