2
Li o the top plate, setting it aside on a so work surface
or on the shipping packaging to prevent damage to the
product's nish.
4.
CAUTION: At this point if you plan to anchor the section, please proceed to Step 5. If you are not
planning to anchor the sections, then please proceed to Step 13.
TOOLS NEEDED: HARDWARE NEEDED:
Step-by-Step Installation Sequence
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
FOOT MOUNTS:
CE1848T and CE1848RCE1815
(4 ) 3/8" x 3.5" 18-8
Stainless Steel Stud Anchors
92188A202
Optional: (4) 3/8"
Rubber Washers
90130A050Hammer Drill
Masonry Drill Bit Set
3/16", and 3/8"
Hammer
Pencil
9/16"Wrench
Wire Brush
Level
Safety Glasses
20.6875
35.0000
SECTION A-A
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
NOTES:
STUD SHOULD BE FLUSH WITH THE FACE OF THE PANEL.
DRAIN HOLES FACE DOWNWARDS
BREAK ALL SHARP EDGES
ALL PARTS LOCATED BY MORTISE AND TENON
CLEAN UP ALL WELDS AND SPATTER
PER NORMAL POWDER-COATED
PART STANDARDS
GRIND ALL BLISTERS
REVISIONS
REV.
DESCRIPTION
ECN TR #
DATE
001
ORIGINAL PRINT
NONE
Canyon Edge 4' Linear Bench w/ Thermory
001
CE1848T
SHEET 1 OF 1
1:5
2/17/2021
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
35.00"
20.70"
20.7475
13.0000
SECTION B-B
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
NOTES:
STUD SHOULD BE FLUSH WITH THE FACE OF THE PANEL.
DRAIN HOLES FACE DOWNWARDS
BREAK ALL SHARP EDGES
ALL PARTS LOCATED BY MORTISE AND TENON
CLEAN UP ALL WELDS AND SPATTER
PER NORMAL POWDER-COATED
PART STANDARDS
GRIND ALL BLISTERS
REVISIONS
REV.
DESCRIPTION
ECN TR #
DATE
001
ORIGINAL PRINT
NONE
Canyon Edge 15" Accent Section
001
CE1815
SHEET 1 OF 1
1:5
2/17/2021
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
20.70"
13.00"