Sterling 72290103-N-0 Specification

Sterling
Brand
Sterling
Model
72290103-N-0
Type
Specification

This manual is also suitable for

Features
•
Compression molded from our exclusive solid Vikrell
®
material
•
Modular 4-piece design
•
Pivot ″snap together″ installation
•
Caulkless seam installation
•
Pre-attached grab bars constructed from anodized
aluminum
•
Convenient shelves provide generous storage
•
Durable, chemical-resistant removable seat
•
Removable seat can be conveniently placed on either
side of shower base
•
Not recommended as a shower base only installation
•
10-year consumer/3-year commercial limited warranty
•
60-1/8″ (1527 mm) x 37-1/4″ (946 mm) x 75-7/8″
(1927 mm) rough-in dimensions include nailing flange
•
60″ (1524 mm) x 36″ (914 mm) x 74-1/2″ (1892 mm)
complete unit finished dimensions
Codes/Standards Applicable
Specified model meets or exceeds the following:
•
CSA B45.0
•
ASTM E662
•
CSA B45.5/IAPMO Z124
•
ASTM E162
60″ SEATED SHOWER BASE AND
SURROUND WITH GRAB BARS
72290103
Colors/Finishes
•
0: White
•
N: Nickel
•
V: Matte Silver
•
Other: Refer to Price Book for additional colors/finishes
Specified Model
Model Complete Unit Description Grab Bar Colors/Finishes Fixture Colors
72290103 60″ seated shower base and
surround with grab bars
❑ N ❑ V ❑ Other_____ ❑ 0 ❑ Other_____
Model Component Description Grab Bar Colors/Finishes Colors/Finishes
72291100 60″ shower base with removable seat ❑ 0 ❑ Other_____
71164103 60″ complete wall set with grab bars ❑ N ❑ V ❑ Other_____ ❑ 0 ❑ Other_____
ACCORD
®
Page 1 of 2
1122779-4-
H
For more information
visit SterlingPlumbing.com
or call 1-800-STERLING
Technical Information
Door maximum width Door maximum height
56-1/8″ (1426 mm) at threshold
56-5/8″ (1438 mm) at top
70-5/8″
(1794 mm)
Removable
seat
Height Surface width Surface length
15-3/4″
(400 mm)
11-3/4″
(298 mm)
21-1/4″
(540 mm)
Installation Notes
Install this product according to the installation guide.
Size the drain cutout to fit the drain assembly that will be
used.
End stud positioning is critical.
Double studding is recommended for pivot shower door
installations.
Studs should be positioned roughly as shown.
Shower base cannot be installed without the wall surround.
60"
(1524 mm)
Backer board
locations
36" (914 mm)
1-1/4"
(32 mm)
55-1/8"
(1400 mm)
3-1/2"
(89 mm)
20-1/2"
(521 mm)
75-7/8"
(1927 mm)
21-1/2"
(546 mm)
1-5/8" (41 mm)
at Midpoint
37-1/4"
(946 mm)
26"
(660 mm)
8"
(203 mm)
Ø 3-5/16"
(84 mm)
Drain Hole
30"
(762 mm)
16-3/8"
(416 mm)
Ø 4-1/2"
(114 mm)
Drain Cutout
16"
(406 mm)
60-1/8" (1527 mm) Min
60-1/4" (1530 mm) Max
4" (102 mm)
10"
(254 mm)
5-1/2" (140 mm)
16-1/2" (419 mm)
16-1/2"
(419 mm)
12"
(305 mm)
Back Wall
3" (76 mm)
16-1/4"
(413 mm)
5-1/2"
(140 mm)
19"
(483 mm)
3" (76 mm)
End Wall
1-1/4"
(32 mm)
16"
(406 mm)
14" (356 mm)
Product Diagram
ACCORD
®
ACCORD
®
60″ SEATED SHOWER BASE AND SURROUND WITH GRAB BARS
Page2of2
1122779-4-
H
  • Page 1 1
  • Page 2 2

Sterling 72290103-N-0 Specification

Sterling
Brand
Sterling
Model
72290103-N-0
Type
Specification
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents