KVM-TEC KT-6032L USBflex single fiber KVM Extender Installation guide

Type
Installation guide

This manual is also suitable for

KVM-TEC KT-6032L USBflex single fiber KVM Extender is a device that allows you to extend the reach of your USB devices over a single fiber optic cable. This can be useful in a variety of applications, such as:

  • Extending the reach of your USB devices to a remote location
  • Isolating USB devices from electrical noise and interference
  • Securing USB devices in a remote location

The KT-6032L supports a wide range of USB devices, including:

  • Keyboards and mice
  • Printers and scanners
  • Webcams and microphones
  • Storage devices
  • And more

The KT-6032L is easy to install and use. Simply connect the local unit to your computer and the remote unit to your USB devices. The two units are then connected via a single fiber optic cable.

KVM-TEC KT-6032L USBflex single fiber KVM Extender is a device that allows you to extend the reach of your USB devices over a single fiber optic cable. This can be useful in a variety of applications, such as:

  • Extending the reach of your USB devices to a remote location
  • Isolating USB devices from electrical noise and interference
  • Securing USB devices in a remote location

The KT-6032L supports a wide range of USB devices, including:

  • Keyboards and mice
  • Printers and scanners
  • Webcams and microphones
  • Storage devices
  • And more

The KT-6032L is easy to install and use. Simply connect the local unit to your computer and the remote unit to your USB devices. The two units are then connected via a single fiber optic cable.

Misprints, errors and technical changes reserved
kvm-tec
First Aid
kvm-tec Supportkvm-tec Support
Phone: +43 2253 81912 - 30Phone: +43 2253 81912 - 30
Kontaktieren Sie
kvm-tec support
Pas d‘alimen-
tation
(Pas de LED)
USB ne foncti-
onne pas
Vériez le
prise de courant
L‘alimentation
électrique est-elle
correcte ? Essayez
une autre unité.
Essayez de repro-
grammer l‘appareil à
l‘aide d‘un program-
mateur JTAG.
Contacter le sup-
port kvm-tec
Est-ce que l‘USB
Appareils branchés
correctement ?
Le câble USB côté
local est-il branché
sur le PC ?
Les périphériques
USB foncti-
onnent-ils directe-
ment sur le PC?
Remplacez le
câble USB du PC
vers le prolonga-
teur local.
Vérier si l‘unité
locale et l‘unité dis-
tante ont le même
micrologiciel.
Vériez si l‘unité
locale ou distante
est à l‘origine du
problème en ch-
angeant d‘abord
l‘unité locale et
ensuite l‘unité
distante vers une
autre unit
Nous sommes à votre disposition pour répondre à vos
questions concernant l‘installation?
Téléchargement du manuel www.kvm-tec.com
ou
kvm-tec Canal d‘installation sur notre page d‘accueil
personnellement +43 2253 81912
Update with USB-Stick
Plug the USB stick with update le into USB Flex.
2. press the button on the back left (if PtP, the USB channel will be
disconnected) ~ 4 sec
3. wait until LED ashes orange (USB stick is scanned for updates) ~
10-20 sec
4. LED lights up specically for 3 seconds
LED red -> no update on stick found (remove stick and start at step 1)
LED green -> Update found, ready to start
5. press button again
6. wait until the update is completed or an error occurs (for PtP local is
updated rst) ~ 2-3 min (PtP ~ 5-6 min)
While update is running, LED ashes green, if data is transferred or
copied, LED ashes very fast.
At the end of the update, the LED ashes orange 4 more times and then
starts the reboot process (the Extender must not be disconnected from
the power supply during this process!)
Check out
our Installation Channel:
www.kvm-tec.com
flex
USB
kvm-tec
Quick
Installation
KT-6032L CPU/LOCAL
KT-6032R CON/REMOTE
Misprints, errors and technical changes reserved Misprints, errors and technical changes reserved
USB vers PC
Quick Installation USBex Fibre local / CPU – remote/ CON
1. Connectez le CON / Remote et le CPU / Local Unit chacun avec l‘alimentation électrique 12V 2A fournie.
2. Branchez ensuite le câble USB à un port USB de votre PC et connectez l‘autre extrémité du câble USB à l‘unité
centrale / locale. Ensuite, connectez les dispositifs USB au CON / Remote Unit.
3. Connectez le CPU / Local et le CON / Remote Unit avec le câble réseau.
Amusez-vous bien - votre extenseur est maintenant prêt pour de nombreuses années d‘utilisation (MTBF environ 10 ans)
1. prise de
courant
12V 1A
1. prise de
courant
12V 1A
2. USB de la
caméra vidéo
2. USB de l‘ap-
pareil photo
2. USB à partir d‘un
joystick
3. Câble à bre optique OM3 jusqu‘à 500m
  • Page 1 1
  • Page 2 2

KVM-TEC KT-6032L USBflex single fiber KVM Extender Installation guide

Type
Installation guide
This manual is also suitable for

KVM-TEC KT-6032L USBflex single fiber KVM Extender is a device that allows you to extend the reach of your USB devices over a single fiber optic cable. This can be useful in a variety of applications, such as:

  • Extending the reach of your USB devices to a remote location
  • Isolating USB devices from electrical noise and interference
  • Securing USB devices in a remote location

The KT-6032L supports a wide range of USB devices, including:

  • Keyboards and mice
  • Printers and scanners
  • Webcams and microphones
  • Storage devices
  • And more

The KT-6032L is easy to install and use. Simply connect the local unit to your computer and the remote unit to your USB devices. The two units are then connected via a single fiber optic cable.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI