Page is loading ...
It is always recommended to anchor the unit to the ground. Drill through
the four holes in the base of the unit using 6mm dia masonry drill to a
depth of 70mm. Screw in the anchor fixings. (These have a self cutting
thread). If not anchoring the unit, fit the self seal plugs BEFORE
BUILDING to seal the fixing holes from underneath. Please note
product must be bolted down to comply with LPS1175.
TOOLS REQUIRED
Power driver POSI-DRIV screwdriver, 6mm dia. masonry drill and a
10mm socket or spanner.
CENTURION PLUS 2
BASE INSTRUCTIONS
Flat and firm base. Recommended: concrete, tarmac or paving flags.
Min. distance from walls/ shrubbery: 1000mm.
Min. base size (WxDxH) 4940mm x 1730mm x 50mm.
LEVELING THE UNIT
Correctly level the constructed unit using the shims (ZCOMPPLAS)
provided prior to fixing the unit to the ground. Slide the packing pieces
under the corners of the unit base as required until an equal gap has
been achieved around the door allowing for its smooth operation and
alignment.
Warning: some panels may weigh over
20Kg. Beware of manual handling
10mm
Spanner
18V
For maintenance instructions of this product visit www.asgardsss.co.uk
x2
SEALANT
LH R. SIDE PANEL
32874 x1
LH EXT. SIDE PNL
32853 x2
F. BASE PNL
32940 x1
R. BASE PNL
32871 x1
EXT BASE PNL
32850 x2
LH DOOR
32943 x1
RH DOOR
32944 x1
FRONT FASCIA
32948 x1
ZSCREW32 x16
ZSILCO1 x3
ZSCREW04 x4
ZSCREW100 x368
ZSCREW340 x24
32670 x24
ZCOMPPLZS02 x16
ZCOMPPLAS22-23-24 x24
8x 2mm, 8x 3mm, 8x 5mm
BASE COVER CHANNEL 37364 x3
SIDE COVER CHANNEL 32916 x6
ROOF COVER CHANNEL
32918 x6
RH F. SIDE PNL
32942 x1
RH EXT. SIDE PNL
32854 x2
LH BACK PANEL
32867 x1
RH BACK PANEL
32876 x1
TOP SHROUD
32945 x2
EXT. TOP SHROUD
32996 x2
RH R. SIDE PNL
32875 x1
F. TOP PANEL
32986 x1
R. TOP PANEL
32987 x1
EXT. TOP PANEL
32927 x2
LH F. SIDE PANEL
32941 x1
Warning: Please keep
this key card safe! Refer
to if replacement key is
required.
00001
YOUR UNIQUE
KEY CODE
ROOF JOINT
STRIP 40446 x6
6mm
Dia.
Posi-Driv
Screwdriver
RH BACK PANEL
32876
RH R. SIDE PANEL
32875
REAR BASE PANEL
32871
x15
1
3
5 6
4
2
x19 x22
x10
PLEASE NOTE ALL SCREWS ARE FIXED FROM THE INSIDE
LH R. SIDE PANEL
32874
x16 x13
R. TOP PANEL
32987
EXT. BASE PANEL
32850 x1
LH BACK PANEL
32867
x3
x15
x7
x16
x3
x15
x7
x13
x4
x4
x4
x4
7 8
9 10
11 12
x44 x22
x13 x44
x6 x30
LH EXT. PANEL
32853
RH EXT. PANEL
32854
x7
x15
x15
x4
x7
x7
x4
x7
x13
EXT. TOP PANEL
32927
F. TOP PANEL
32986
REPEAT 6-8
x4
x4
x4
x4
x7
x7
F. BASE PNL
32940
RH F. SIDE PNL
32942
LH F. SIDE PANEL
32941
FRONT FASCIA
32948
x15
x15
x7
x7
x3
x3
www.asgardsss.co.uk
13 14
15 16
17 18
x16
054366/11.05.17/KW/REV3
REMOVE SCREWS WHICH ALIGN
WITH THE COVER CHANNELS.
ALIGN AND PLACE SCREWS BACK
!
BASE COVER CHANNEL 37364
1ST TOP SHROUD
32945
2ND TOP SHROUD
32945
x4
x3
x3
x2
x2
x3
x4
x4
x4
x3
x3
x3
x3
x3
ROOF JOINT STRIP 40446
APPLY TO ALL
EXT. TOP SHROUDS
32996
SHROUDS 32996 & 32945
ROOF JOINT STRIP 40446
LH DOOR
32943
RH DOOR
32944
x24
x24
x12
ROOF JOINT STRIP END
40446
32670
SIDE COVER CHANNEL 32916
ROOF COVER CHANNEL 32918
ROOF STRIP
/
