It is always recommended to anchor down the unit to the ground. Drill
through the four holes in each of the base of the unit using 6mm dia
masonry drill to a depth of 70mm. Screw in the anchor fixings. (These
have a self cutting thread). If not anchoring the unit, fit the self seal plugs
BEFORE BUILDING to block the fixing holes from underneath. Please
note, product must be bolted down to comply with LPS1175
TOOLS REQUIRED
Power driver POSI-DRIV screwdriver, 6mm dia. masonry drill and a
10mm socket or spanner.
GLADIATOR PLUS 2
ZSCREW32 x16
ZSILCOL1 x3
ZSCREW04 x4
ZSCREW100 x515
ZSCREW340 x24
32670 x26
10 mm
Spanner
18V
ZCOMPPLZS02 x16
ZCOMPPLAS22-23-24 x24
8x 2mm, 8x 3mm, 8x 5mm
BASE INSTRUCTIONS
Flat and firm base. Recommended: concrete, tarmac or paving flags.
Min. distance from walls/ shrubbery: 1000mm.
Min. base size (WxDxH) 2410mm x 4940mm x 50mm.
LEVELING THE UNIT
Correctly level the constructed unit using the shims (ZCOMPPLAS)
provided prior to fixing the unit to the ground. Slide the packing pieces
under the corners of the unit base as required until an equal gap has
been achieved around the door allowing for its smooth operation and
alignment.
ROOF BRACE 39897 x3
For maintenance instructions of this product visit www.asgardsss.co.uk
Warning: Please keep
this key card safe! Refer
to if replacement key is
required.
x2
Warning: some panels may weigh over
20Kg. Beware of manual handling
SEALANT
00001
YOUR UNIQUE
KEY CODE
FRONT BASE PNL
39841 x1
TOP COVER CHANNEL 40063 x6
FLOOR COVER CHANNEL 40062 x6
FASCIA 39848 x1
RH DOOR
32944 x1
RH FRONT PANEL 039861 x1
LH FRONT PANEL 39860 x1
LH DOOR
32943 x1
RH FRT SIDE PANEL
39815 x1
SIDE COVER CHANEL 32916 x6
LH FRT SIDE PANEL
39814 x1
RH FRT TOP PANEL
39873 x1
LH FRT TOP PNL
39871 x1
LONG TOP CAP
39893 x1
SHORT TOP CAP
39892 x1
EXTENSION TOP CAP
40095 x2
RH EXT TOP PNL
40066 x2
LH EXT TOP PNL
40065 x2
RH REAR TOP PANEL
39869 x1
LH REAR TOP
PNL 39867 x1
ROOF JOINT
STRIP 40881 x6
LH BACK PANEL
39832 x1
LH REAR SIDE PANEL
32874 x1
RH REAR SIDE PANEL
32875 x1
REAR BASE PNL
39831 x1
RH BACK PANEL
39833 x1
TOP FRONT BACK CHANNEL
40094 x4
LH EXT SIDE PANEL
32853 x2
RH EXT SIDE PANEL
32854 x2
EXT BASE PANEL
40064 x2
6mm
Dia.
Posi-Driv
Screwdriver
1
5 6
2
4
FLOOR COVER CHANNEL 40062 x6
3
PLEASE NOTE ALL SCREWS ARE FIXED FROM THE INSIDE
x18 x9
x24 x4
x22 x22
x15
REAR BASE PNL
39831
EXT BASE PANEL
40064
EXT BASE PANEL
40064
x4
x18
x4
x9
x9
x9
FRONT BASE PNL
39841
x7
RH REAR SIDE PANEL 32875
LH BACK PANEL 39832
x8
x8
x8
RH BACK PANEL 39833
IF YOU HAVE AN OPTIONAL RAMP,
PLACE UNDERNEATH FRONT
BASE PANEL AT THIS STAGE
!
7
9
8
10
11 12
PLEASE NOTE ALL SCREWS ARE FIXED FROM THE INSIDE
RH FRONT PANEL 039861
FASCIA 39848
x5
x5
x15
x3
x15
x3
x32
x48
x36
x10
x15
RH BACK PANEL 39833
x7
LH REAR SIDE PANEL 32874
LH FRT SIDE PANEL
39814
RH FRT SIDE PANEL 39815
SIDE COVER CHANELS 32916
LH FRONT PANEL 39860
x22 x28
x7
x9
x9
x7
x7
x7
LH EXT SIDE PANEL 32853
RH EXT SIDE PANEL 32854
REPEAT STEP 8
x7
x8
x8
x8
x8
x8
x8
x7
13
17 18
14
15 16
PLEASE NOTE ALL SCREWS ARE FIXED FROM THE INSIDE
x16
TOP FRONT BACK CHANEL
40094
x4
x20
x74
x26
x6
x6
x4
x4
32670
x24
LH REAR TOP PNL 39867
LH EXT TOP PNL 40065 x2
LH FRT TOP PNL 39871
x6
x6
RH REAR TOP PNL
39869
LH REAR TOP PNL
39867
LH EXT TOP PNL
40065
RH EXT TOP PNL
40066
x6
x6
LH EXT TOP PNL
40065
RH EXT TOP PNL
40066
LH FRT TOP PNL
39871
RH FRT TOP PNL
39873 x1
x4
x6
x6
x7
x7
x4
x6
x6
x4
x4
x6
x6
x4
x4
19
21
20
22
23 24
PLEASE NOTE ALL SCREWS ARE FIXED FROM THE INSIDE
x12
x4
x4
x4
ROOF JOINT STRIP 40881
APPLY TO ALL INSIDE EDGES AND FIT FIRST
ROOF JOINT STRIP END
40881
TOP COVER CHANNEL 40063
ROOF BRACE 39897
LONG TOP CAP
39893
SHORT TOP CAP
39892
EXTENSION TOP CAPS
40095 x2
x6
x6
x6
x6
x6
x6
x6
x6
x6
x6
x6
x6
x3
x3
x3
x3
x3
x3
x3
x3
x3
x3
x3
x3
NO SCREWS REQUIRED
TOP END OF STRIP TRAPPED
UNDER TOP CAP
!
25 26
27 28
29
x24
RH DOOR
32944
LH DOOR
32943
x40
ROOF STRIP
x4
x2
x2
x3
x3
x3
x3
x3
x3
x3
x3
54947/23.09.19/KW/REV3
x16
LEVEL SHED UNTIL DOORS
ALIGN USING ZCOMPPLAS
AS SUITABLE
!
ZCOMPPLAS22-23-24
/
