Danfoss SpeedUp Eco Wall Heating in Wet Systems Installation guide

Danfoss
Brand
Danfoss
Model
SpeedUp Eco Wall Heating in Wet Systems
Type
Installation guide

Danfoss SpeedUp Eco Wall Heating in Wet Systems

Danfoss SpeedUp Eco Wall Heating in Wet Systems is a surface heating system that is easy to install thanks to its click system, yet highly efficient and comfortable. SpeedUp Eco offers unique benefits like low energy consumption, silent operation, fire resistance, and easy installation & handling. It is suitable for all types of buildings and can be installed in walls, floors, and ceilings. The system consists of heating panels, a metal grid, and a plaster layer. The heating panels are made of a lightweight, durable plastic material and have a built-in heating element. The metal grid is used to support the plaster layer and to ensure even heat distribution. The plaster layer is a thin, lightweight material that is applied over the metal grid.

Danfoss SpeedUp Eco Wall Heating in Wet Systems

Danfoss SpeedUp Eco Wall Heating in Wet Systems is a surface heating system that is easy to install thanks to its click system, yet highly efficient and comfortable. SpeedUp Eco offers unique benefits like low energy consumption, silent operation, fire resistance, and easy installation & handling. It is suitable for all types of buildings and can be installed in walls, floors, and ceilings. The system consists of heating panels, a metal grid, and a plaster layer. The heating panels are made of a lightweight, durable plastic material and have a built-in heating element. The metal grid is used to support the plaster layer and to ensure even heat distribution. The plaster layer is a thin, lightweight material that is applied over the metal grid.

1 Installation of SpeedUp Eco Wall Heating in Wet Systems
Fig. 1: Attach the perimeter insulation by stapling it into
place.
Fig. 2: To attach the individual system panels apply adhesive
grout or tile adhesive using the comb spatula.
Fig. 3: Start with header/blank panels according to the lay-out
drawing.
Fig. 4: The pre-formed cutting edges mean that the system
elements are easy to shorten using the circular hand saw/jig
saw. Fill the boundary and electrical areas with blank panels.
Fig. 5: Mark individual pipe channels and cut out using the
rotary cutter.
Fig. 6: Drill at least 8 holes for wall dowels (70 mm) per m² and
attach dowel bottom section.
Installation Guide
SpeedUp Eco Wall Heating in Wet Systems
Danfoss Heating Solutions VIEUA202
1
Fig. 7: Press the composite pipe into the pipe channels in a
wide arc from bottom to top. See distributor for connection.
Fig. 8: Attach wall heating metalgrid from top to bottom,
lightly tensioned and with 10 cm overlap, using the dowel
upper section.
Fig. 9: Before applying the plaster carry out the required
pressure test to at least 6 bar, according to the test report.
Fig. 10: The single 15 mm thick layer of plaster can be
smoothed or matted as required.
Installation Guide
SpeedUp Eco Wall Heating in Wet Systems
Danfoss A/S
Heating Solutions
Haarupvaenget 11
8600 Silkeborg
Denmark
Phone:+45 7488 8000
Fax: +45 7488 8100
Email: [email protected]
www.heating.danfoss.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective
companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
VIEUA202 Produced by Danfoss Heating Solutions © 11/2010
  • Page 1 1
  • Page 2 2

Danfoss SpeedUp Eco Wall Heating in Wet Systems Installation guide

Danfoss
Brand
Danfoss
Model
SpeedUp Eco Wall Heating in Wet Systems
Type
Installation guide

Danfoss SpeedUp Eco Wall Heating in Wet Systems

Danfoss SpeedUp Eco Wall Heating in Wet Systems is a surface heating system that is easy to install thanks to its click system, yet highly efficient and comfortable. SpeedUp Eco offers unique benefits like low energy consumption, silent operation, fire resistance, and easy installation & handling. It is suitable for all types of buildings and can be installed in walls, floors, and ceilings. The system consists of heating panels, a metal grid, and a plaster layer. The heating panels are made of a lightweight, durable plastic material and have a built-in heating element. The metal grid is used to support the plaster layer and to ensure even heat distribution. The plaster layer is a thin, lightweight material that is applied over the metal grid.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers