LAMONA SNK2125 Operating instructions

LAMONA
Brand
LAMONA
Model
SNK2125
Type
Operating instructions

This manual is also suitable for

Abrasive
cream
cleaners
Chlorine
or
Bleach
Acid
Alkali
Caustic
Washing
Up Liquid
180°c max temperature
Single Bowl Black Granite Inset/Undermount Sink
1.5 Bowl Black Granite Inset/Undermount Sink
SNK2120
SNK2122
HD612042
Care and Maintenance
Do not use abrasive cleaning products as these
may scratch the surface of the sink
Installation
Measure and Cut
1
2
3
4
5
6
Follow the dimensions shown for the cutout size of your sink bowl depending
on a inset or undermount installation.
IMPORTANT
When measuring and positioning the sink to the top, ensure enough gap is left for the
tap hole position behind the bowl. This should be cut at the same time as the sink
cut-out
Inset Sink
Fit the 4 sink clips to the
side of the sink. Separate
the front two mounted clips,
then t the sink into the
cut-out. Centre the sink and
tighten the screws from the
underside to clamp sink in
position.
Note: Use strips of timber
to pack the underside of
the sink if your worktop is
less than 30mm thick.
Undermount Sink
Drill four 8mm holes in the
locations shown and tap
the metal inserts into place.
Note: Glue inserts into
position.
Drill four holes, one in each corner of the
inner line. Use a jigsaw to cut-out.
Note: When tting an undermount sink, a
smoother nish is required to the worktop
cut-out. Use a router to achieve this nish.
Sand to a nal nish.
The worktop will require notching on the
underside for the overow in an inset sink
application (see image below).
Clean around the cut-out removing any dust then
seal around the cut-out using a waterproof sealant.
For inset sinks use silicone around the rim to secure
the bowl in position.
Fit the sink to the underside
of the worktop, making sure
the bowl is concentric to the
cut-out. Push down rmly to
adhere silicone seal.
Fit the brackets to the
worktop inserts so they
clamp onto the rim of the
sink.
Note: Silicone the thread of
the screws for extra strength.
Wipe away any excess
silicone
Note: Do not use power
tools to tighten screws
Note: Do not use power
tools to tighten screws
Cutting for Inset Sink
Cutting for Undermount Sink
Silicone
Sealant
Sealant
Undermount Sink
Inset Sink
Worktop
Underside
12mm
20mm
x2
For worktops for less than
30mm thick, use timber
batons to secure to for inset
application
For worktops 30 - 40mm thickFor worktops less than 30mm
(Additional packing required)
Worktop
Underside
30mm
Glue
x4
8m
m
8mm bit
Sink Rim
x4
Worktop
Underside
R=10mm R=30mm R=15mm
530mm
410mm
Inset Sink
Cut-out
Undermount Sink
Cut-out
Option 1
Undermount Sink
Cut-out
Option 2
Worktop Worktop Worktop
520mm
400mm
490mm
370mm
5mm
40mm
Top surface of Workto
p
5mm
15mm
  • Page 1 1
  • Page 2 2

LAMONA SNK2125 Operating instructions

LAMONA
Brand
LAMONA
Model
SNK2125
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents