DIODE LED 0-10V Dimmable LED Drivers Installation guide

Brand: DIODE LED

Model: 0-10V Dimmable LED Drivers

Type: Installation guide

This manual is also suitable for

Commercial Grade 0-10V Dimmable Drivers

1.877.817.6028

www.DiodeLED.com

[email protected] www.DiodeLED.com

INSTALLATION GUIDE

1 OF 4

0-10V DIMMABLE LED DRIVER

• Install in accordance with the Naonal Electric Code, and local

regulaons.

• This product is intended to be installed and serviced by a qualied,

licensed electrician.

• Only install compable LED xtures and controls. Contact technical

support or visit the product page for compable products.

• Proper heat dissipaon will prolong the working lifespan of this product.

Install in a well-venlated area free from explosive gases and vapors.

• Ensure applicable wire is installed between driver, xture, and any

controls in between. When choosing wire, factor in voltage drop,

amperage rang, and type (in-wall rated, wet locaon rated, etc.).

Inadequate wire installaon could overheat wires, and cause a re.

• Do not install if product has any visible damage.

• Do not modify or disassemble this product beyond instrucons or the

warranty will be void.

Safety & Warnings

Dry/Wet

Location

Dimmable

Read all warnings and installaon instrucons thoroughly.

WARNING

IG102119-2.0

Prior to installaon, ensure all components are a compable system. Congure and pre-test your LED system prior to permanent installaon to ensure

all components are operang correctly. Install in accordance with the NEC and local regulaons.

1. Turn OFF 120~277VAC power at the main breaker prior to installaon.

2. Determine locaons to install the driver, xture and control. See ‘System Diagram.’

3. Aach appropriate load and 0-10V control/dimmer to the driver. See ‘Wiring Connecons.’

4. Install addional components and accessories. Once complete, turn main power ON.

Input Voltage

100-277VAC~ at 50/60Hz

Output Voltage See driver label for output voltage.

Ambient Temp † -40 ~ +122°F (-40 ~ +50°C)

Max Load Ensure to de-rate the labeled load 20%.

See dimmer switch for min. load requirements.

†

Do not install product in an environment outside the listed ambient

temperature. Ensure adequate airow and heatsinking is considered

when mounng/installing.

For full specicaons, see the ‘Specicaon Sheet’ at the online product

page.

Ensure applicable wire is installed between driver, xture, and any controls between. When choosing wire, factor in voltage drop, amp rang, and type

to prevent re or electric shock.

AC/N (White)

AC/L (Black)

V+ (Red)

V− (Blue)

120-277VAC~

50/60 Hz

To Low Voltage

LED Load

V+ (Purple)

V− (Gray)

To 0-10V

Control/

Dimmer

Aach ground wire to mounng

hole or juncon box chassis.

Quick Specs

Installation

Wiring Connections

WARNING Shock Hazard. May result in serious injury or death.

Turn o power at circuit breaker before installing this product.

Included Models

DI-DM-12V60W-0-10V DI-DM-24V100W-0-10V

* Commercial Grade 0-10V drivers will ulize Blue(+) and White (-) dimming wires

1.877.817.6028

www.DiodeLED.com

[email protected] www.DiodeLED.com

INSTALLATION GUIDE

2 OF 4

0-10V DIMMABLE LED DRIVER

IG102119-2.0

V+

V-

LED Tape Light / Fixture‡‡

V+

V-

AC Power

50/60Hz

V- (Gray)

Input

Output

V+

V-

Class 2, 0-10V Driver‡

Class 2 Only.

Install applicable

gauge wire / type.

V+

V- V- (Blue)

V+ (Red)

V+ (Purple)

0-10V

Dimmer / Control

to dimmerto load

GND

Driver Line Hot (Black)

L (Black) Dimmer Input Hot (Black)

GND

Dimmer Switched Hot (Red)

V+

V-

LED Tape Light / Fixture‡‡

V+

V-

AC Power

50/60Hz

V- (Gray)

Input

Output

V+

V-

Class 2, 0-10V Driver‡

Class 2 Only.

Install applicable

gauge wire / type.

V+

V-

V- (Blue)

V+ (Red)

V+ (Purple)

0-10V

Dimmer / Control

to dimmerto load

V- (Blue)

V+ (Red)

Red

White (N)

Red

Black (L) Black

V+

V-

On/Off Relay Module

GND

The following diagrams are provided as example system designs. Always review each component installaon guide for detailed and up-to-date wiring

instrucons. Install in accordance with NEC and local regulaons.

0-10V Dimmable Driver System Diagram (Leviton® Dimmer with No Power Pack)

0-10V Dimmable Driver System Diagram (Lutron® Dimmer with Lutron® Power Pack)

‡ Refer to driver or controller specicaons for a compable juncon box.

‡‡ See xture specicaons for maximum series run limits.

System Diagrams

1.877.817.6028

www.DiodeLED.com

[email protected] www.DiodeLED.com

INSTALLATION GUIDE

3 OF 4

0-10V DIMMABLE LED DRIVER

IG102119-2.0

System Diagrams Cont’d

MFG Product Descripon Model # Power Input

Power Pack

Required

for On/O

Control?

Power Pack

Required for

Occupancy

Sensor?

Lutron®DIVA® 0-10V Preset Dimmer DVTV Control: 0-10VDC, 30mA

Switch: 24VDC, 100mA Yes* Yes*

Lutron®NOVA® 0-10V Slide-to-o Dimmer NFTV Control: 0-10VDC, 30mA

Switch: 24VDC, 100mA Yes* Yes*

Lutron®NOVA T® 0-10V Slide-to-o Dimmer NTFTV Control: 0-10VDC, 30mA

Switch: 24VDC, 100mA Yes* Yes*

Leviton®ILLUMATECH® 0-10V Preset Dimmer IP710-LFZ 120VAC and 277VAC. See MFG

installaon guide for maximum loads. No Yes†

Compatible Controls

MFG / Product Product Descripon Model # Power Input Control Input Power Output

Lutron® Series

Power Packs

PP-120H 120VAC, 60 Hz

24VDC, 5mA 24VDC, 100mA

PP-230H 230VAC, 50/60 Hz

PP-277H 277VAC, 60 Hz

PP-347H 347VAC, 60 Hz

Auxillary Power Pack PP-SH N/A 24VDC, 5mA N/A

Leviton®

Occupancy Sensor

Power Packs

Auto On OPP20-0D1

See MFG Specs See MFG Specs See MFG Specs

Auto/Manual On, Local Switch OPP20-0D2

Auto On, Photocell OPP20-RD3

Auto/Manual On, Local Switch,

Photocell OPP20-RD4

* Lutron® Series Power Packs must be installed to support On/O control and when installing Lutron® occupancy sensor controls. Specify the Auxillary

Power Pack when installing more than 3 Lutron® occupancy sensors.

† The Leviton® IP710-DLZ dimmer supports On/O control. The Leviton Power Pack is required when installing Leviton® occupancy sensor controls.

To ensure a safe installaon and opmal lighng/dimming performance, specify the following controls with our 0-10V LED dimmable drivers. Some

dimmers require an addional power pack (relay switch) to support On/O control or occupancy sensor control. Many 0-10V dimming controls not

listed below may also perform well, however we cannot guarantee compability. For addional informaon, please contact technical support.

Controls / Dimmers

Power Packs

0-10V

Dimmer

LED

Driver

LED

Driver

LED

Driver

LED

Driver

LED

Driver

Up to 50 drivers

may be installed

within a 300 .

wiring distance.

Remote Wiring Distance: 300 .

1 2 3 4 5

Purple

Gray

Purple

Gray

Purple

Gray

Purple

Gray

Purple

Gray

Purple

Gray

0-10V Dimmable Driver Large Install System Diagram (Example)

1.877.817.6028

www.DiodeLED.com

[email protected] www.DiodeLED.com

INSTALLATION GUIDE

4 OF 4

0-10V DIMMABLE LED DRIVER

IG102119-2.0

QUESTIONS? Visit www.DiodeLED.com or contact Customer Support at inf[email protected]

or 1.877.817.6028 Monday through Friday, 7:00am - 5:00pm PST.

Additional Resources

Visit the online product page at www.DiodeLED.com for addional product specicaons & warranty informaon.

• 0-10V DIMMABLE LED DRIVER Specicaon Sheet

For full specicaons.

• Voltage Drop Charts

Use to specify appropriate wire gauge for installaon. Available at the ‘Tools & Resources’ page at www.DiodeLED.com.

Troubleshooting

Fixture does not illuminate

• See ‘System Diagram’ and installaon guides of all components. Ensure

the system is wired correctly.

• Verify polaries are correct.

• Ensure a compable constant voltage dimmable xture is installed.

• Ensure the driver and xture have the same voltage speciaons (12V

& 12V, or 24V & 24V).

Fixture does not dim

• Ensure a compable constant voltage dimmable xture is installed.

• Ensure a compable 0-10V control is installed.

• Verify Purple (V+) and Gray (V-) data wires connected to 0-10V control

are not swapped.

Fixture dims but does not turn o

• Verify if the 0-10V control requires an addional power pack (relay

switch) to turn the xture on/o.

• Ensure not to mix & match power packs and dimmers from dierent

manufacturers.

There is a delay when dimmer is switched o • This is normal when loading the driver with small loads. To reduce any

switching delays, install a larger load on the driver.

Fixture is quickly ashing or ickering

• Verify a compable 0-10V control is installed.

• Ensure a compable constant voltage dimmable xture is installed.

• Ensure all connecons are properly secured.

Fixture is slowly ashing • Ensure driver is not overloaded. An overloaded driver will cause the

internal auto-reset to trip repeatedly.

Prior to troubleshoong, ensure a compable system is installed. Verify compable xtures, drivers, controls and addional components were specied

correctly.

DIODE LED 0-10V Dimmable LED Drivers Installation guide

Brand: DIODE LED

Model: 0-10V Dimmable LED Drivers

Type: Installation guide

This manual is also suitable for

Commercial Grade 0-10V Dimmable Drivers

Download PDF

report

DIODE LED 0-10V Dimmable LED Drivers Installation guide

This manual is also suitable for

DIODE LED 0-10V Dimmable LED Drivers Installation guide

Related papers

Other documents