Santec SNC-637ID User manual

Version 1.0sfi/0511/engl/A6

USER MANUAL

IP day/night PTZ camera

in weather-proof housing

Model:

SNC-637ID

Dear customer,

Thank you for purchasing a high quality SANTEC device.

We recommend that you read this manual thoroughly before operating your new

system for the first time. Please follow all instructions and observe the warnings

contained in this manual.

Please contact your local dealer or use the SANTEC Service Hotline if you have any

questions or if you wish to claim for a service or warranty.

You will find further information on our website:

www.santec-video.com

in any form or by any means (electronic, mechanical, photocopying, recording or otherwise), without

the written prior permission of Sanyo Video Vertrieb AG.

No reproduction of any part or excerpts thereof are permitted.

Errors excepted. Specifications are subject to change without notice for quality improvement.

SANTEC is a registered trademark of Sanyo Video Vertrieb AG. All other companies or products

mentioned in this publication are trademarks, registered trademarks or brands of the respective

company. They are not connected in any way with Sanyo Video Vertrieb AG.

SANTEC Service Hotline:

+49 / 900 / 1 72 68 32

+49 / 900 / 1 SANTEC

(if available from your country)

[email protected]

User manual SNC-637ID

_________________________________________________________________________________

- 3 -

Safety precautions

Caution

Description of symbols

Danger: This symbol is intended to alert the user to the presence of un-insulated

"dangerous voltage" within the product‟s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to a person.

Warning: This symbol is intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the literature accompanying

the appliance.

CE compliance

Attention: Any changes or modifications to this appliance which have not been explicitly

approved of by the respective regulatory authority, may lead to a prohibition of usage of this

appliance.

This appliance complies with the CE guidelines.

User manual SNC-637ID

_________________________________________________________________________________

- 4 -

Safety instructions

Before operating the appliance, please read this manual carefully and retain it for further

reference.

Before cleaning the appliance, it has to be switched off and unplugged from the power outlet.

Wipe the appliance with a soft damp cloth.

Do not use harsh cleansers or aerosols for cleaning. The type label may not be replaced.

Do not use attachments unless recommended by the manufacturer as they may affect the

functionality of the appliance and result in the risk of fire, electric shock or injury.

Never install the appliance in areas exposed to water or other liquids.

The appliance has to be installed in a safe and stable location which is able to carry the weight of

the appliance. Quick stops, excessive force, and uneven surfaces may cause the appliance to fall

causing serious injury to persons and damage to objects.

Openings in the appliance, if any, are provided for ventilation to ensure reliable operation of the

appliance and to protect if from overheating. These openings must not be covered or blocked.

Please make sure that the appliance does not overheat.

The appliance should only be operated from the type of power source indicated on the marking

label. If you are not sure of the type of power supplied at the installation location, please contact

your local dealer.

An appliance which is powered through a polarized plug (a plug with one blade wider than the

other) will fit into the power outlet only one way. This is a safety feature. If you are unable to insert

the plug into the outlet, try reversing the plug. Do not defeat the safety purpose of the polarized

plug.

If the appliance is powered through a grounding-type plug, the plug will only fit into a grounding-

type power outlet. This is a safety feature. If your outlet does not have the grounding plug

receptacle, contact your local electrician.

Route power cords and cables in a manner to protect them from damage by being walked on or

pinched by items places upon or against them.

For protection of the appliance during a lightning storm or when it is left unattended and unused

for a longer period, unplug the appliance from the wall outlet. Disconnect any antennas or cable

systems that may be connected to the appliance. This will prevent damage to the appliance due to

lightning or power-line surges.

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric

shock.

Never insert items into the openings of the appliance. They may touch parts under electric current

which may cause an electric shock.

Never pour any liquids over the appliance.

User manual SNC-637ID

_________________________________________________________________________________

- 5 -

In case of any operating interruption or a complete operating failure please switch off the

appliance and disconnect it from the wall outlet. Never attempt to service or repair the appliance

yourself, as opening or removing covers may expose you to dangerous voltage or other hazards.

Refer all servicing to qualified service personnel.

When replacement parts are required, be sure that the service technician uses replacements parts

specified by the manufacturer or that have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

Upon completion of any service or repairs to the appliance, ask the service technician to perform

safety checks to verify that the appliance is in proper operating condition.

The appliance should only be installed by qualified service personnel and has to comply with local

specifications and regulations.

Never point the camera at an object with a high degree of luminance. Bright vertical or horizontal

lines can result in a distortion (outshine) of the entire image on the monitor. This artifact is not an

error but a particularity of semiconductor CCDs when they are directly exposed to a powerful light

source.

At the installation site, the camera has to be adjusted to the given light conditions (see OSD).

Please respect the local legal regulations on waste if you need to dispose of discarded appliances.

This symbol means that electrical appliances need to be disposed of properly and not

simply with unsorted household refuse. Please respect local regulations on waste

disposal.

About this user manual

This manual aims at assisting the user on how to operate camera SNC-637ID.

This manual is subject to rigid quality control. However, no guarantee can be given that

mistakes are not present. We reserve the right to make changes to the manual without prior

notice.

Before operating the appliance, please read this manual carefully and retain it for further

reference.

Verify that all appliance items are included in the delivery. Should items be missing, do not

operate the appliance and contact your local dealer.

Never attempt to repair the appliance yourself. This should only be done by qualified service

personnel.

Improper handling of the appliance will invalidate the warranty.

User manual SNC-637ID

_________________________________________________________________________________

- 6 -

1. FEATURE

1.1 Package

1x camera SNC-637ID

1x SanView Lite software

1x audio cable

1x I/O cable

1x user manual

1.2 Dimension and Connector Description

1.2.1 Dimensions

296

276.6

118.6

80

100

138.6

4- 8

All dimensions in mm.

User manual SNC-637ID

_________________________________________________________________________________

- 7 -

1.2.2 Connector Description

DC 12V Power Input : The SNC-637ID Camera has a port that can output DC12V

for the analog camera module.

Digital Output

Digital Input

Video Output : The SNC-637ID Camera supports one analog video out of

composite signal with BNC connector.

Ethernet Port : Standard RJ45 connector. Supporting NWAY.

Reset Button

Step 1 : Switch off SNC-637ID Camera by disconnecting the power cable.

Step 2 : Using a suitable pointed object, press and continue to hold the Reset

Button depressed. While continuing to hold the reset button depressed, reconnect

the power cable.

Step 3 : Keep holding the reset button depressed around 6 seconds, release the

reset button. The unit will start up with factory default settings.

DIP Switch (Baud rage & Address setting)

: Please refer to the 2.4.3 for more descriptions

Sensor I/O Port

(No Network support)

User manual SNC-637ID

_________________________________________________________________________________

- 8 -

2. INSTALLATION

2.1 Installation

It explains under the condition of using Static IP between User s PC and the SNC-637ID.

To install, the SNC-637ID should connect to the PC directly or to Local Network.

1) Connect the SNC-637ID to the PC by LAN cable (Cross Cable)

2) Supply the power to the SNC-637ID (Allowed to use Regulated Power Supply)

3) After 2minute of power supplying, the booting is finished by checking LINK LED-On.

2.2 Video Check

Basic network setting value of SNC-637ID is to be ;

 IP Address : 192.168.1.168

 Subnet Mask : 255.255.255.0

 Gateway : 192.168.1.1

To connect SNC-637ID inusers PC, change the setting value of PC network environment.

Pic. 0 1 Network Setting of User PC

User manual SNC-637ID

_________________________________________________________________________________

- 9 -

Set IP Address, Subnet Mask and Gate-way of User s PC with 192.168.1.50,

255.255.255.0 and 192.168.1.1 as shown on [Pic. 2-1].

Pic. 0 2 Web Browser Input

Run Web Browser as [2-2] and input 192.168.1.168 in URL and click Enter ,then [2-3]is

to be shown. In case [2-3] does not appear, re-set Hardware (Reset Button in Camera)

to reboot and run Web Browser, input 192.168.1.168 in URL line and click Enter .

Pic. 0 3 SNC-637ID Log-in Page

Default login information:

User name: admin

Password: 9999

Table 0-1 User ID, Password, Rights

User ID

User Password

Rights

guest

Monitor only

admin

9999

All Function

Above [Table 2-1] is the value basically set in SNC-637ID.

Change the User Information in General Setting of 4. Expert Setting

after installation of SNC-637ID.

User manual SNC-637ID

_________________________________________________________________________________

- 10 -

Click (1) after input ID:root, Password:root in [2-4].

Message Window [2-4] appear soon, click Yes .

If click No , Web Viewer doesnt work. .

Upon installation, Web Viewer [Pic. 2-5] appear and image of Camera is to be seen.

Pic. 0 5 Web Viewer

User manual SNC-637ID

_________________________________________________________________________________

- 11 -

2.3 DIP Switch Setup

Before installing the camera, set up the DIP switch to configure the camera ID and

the communication protocol.

 Camera ID Setup

 ID numbers of cameras are set up with binary numbers. See the

examples shown below.

1

2

3

4

5

6

7

8

Binary Value

1

2

4

8

16

32

64

128

ex) ID=5

on

off

on

off

ex) ID=10

off

on

off

on

off

 The camera ID range is “1~255”. Camera ID must not be “0”!

 The factory default of the camera ID is “1”.

 Match the camera ID with the Cam ID setting of your DVR or

Controller to control the camera.

 If you are connecting a single camera to a controller, terminate the

camera. When connecting more than one camera to a single

controller, terminate the last camera on the communication line.

The last camera means the camera farthest in cable length from

the controller.

 Note that the total length of the communication cable betweena

controller and the camera(s) on the same communication line

must be less than 1.2Km.

ON

1 2 3 4 5 6 7 8

User manual SNC-637ID

_________________________________________________________________________________

- 12 -

 Communication Protocol Setup

 Select an appropriate Protocol with the DIP switch combination.

Switch Mode

Protocol

P0

(Pin 1)

P1

(Pin 2)

P2

(Pin 3)

OFF

PELCO-D, 2400 bps

ON

OFF

PELCO-D, 9600 bps

OFF

ON

OFF

PELCO-P, 4800 bps

ON

OFF

PELCO-P, 9600 bps

Others

Reserved

 Match the camera protocol with the camera protocol in the setting of your

DVR or controller to control the camera.

 Adjust the DIP switch after turning off the camera. If you changed

thecamera protocol by changing the DIP S/W, the change will be effective

after you reboot the camera.

 The factory default protocol is “Pelco-D, 9600 bps”.

1 2 3 4

ON

User manual SNC-637ID

_________________________________________________________________________________

- 13 -

3. Basic Setting

3.1 Check Network and Installation Type

This Chapter is for basic setting of SNC-637ID. To install Hardware of SNC-637ID Network

Camera, basic understanding of Network is required. Please refer to Chapter 6 in case

knowledge of Network Environment is required.. There is 2 ways to install Hardware, The

one is to install SNC-637ID without IP sharing Device under Cable Modem or Leased

Line, the other one is to install SNC-637ID under IP sharing Device , which is required

necessarily under PPPoE environment, and even under Leased Line or Cable Modem. The

default IP Address of SNC-637ID is preset to 192.168.1.168 and Subnet Mask to

255.255.255.0 and Gateway to 192.168.1.1 in ex-factory. This explanation is based upon

default value of ex-factory.

Caution 1 : Check Video before installation, on 2. Install and Video Check .

Caution 2 : In case using IP sharing Device, only Global IP is available.

Caution 3 : SNC-637ID does not support PPPoE. IP Sharing Device is required to

connect to SNC-637ID under PPPoE.

User manual SNC-637ID

_________________________________________________________________________________

- 14 -

3.2 Installation Without IP sharing device (Router)

3.2.1 Static IP Setup

1) After checking Video in Video Check , go to the next step.

2) Connect SNC-637ID to PC with LAN Cable (Cross Cable).

3) Cable connection and Network Setup should be same as shown in 2. Install and

Video Check .

4) Run Web Browser and input 192.168.1.168 in URL and click Enter, then [Pic. 3-1]

will appear.

Pic. 3 1 Main Page of SNC-637ID Network Camera

5) Put admin in ID and Password line, click Login , then [3-1] Administrator's Page will

be shown. (ID, Password of SNC-637ID is presetas admin/9999 in Administrator s

Page. Change Administrator s ID and Password in General Setting of 4. Expert

Setting

User manual SNC-637ID

_________________________________________________________________________________

- 15 -

Pic. 3 2 Administrator‟s Page

6) Click Network at menu. And then click WAN. Pic. 3-3 will be followed

Pic. 3 3 WAN Setting

7) In WAN Setting of [3-4], and input IP Address, Subnet Mask, Gateway, HTTP Port

according to Network environment to connected SNC-637ID to.

8) For setting of DNS , input DNS Address to fit with Network Environment to set. Use

DNS value normally set in PC.

9) DNS Address should be necessarily input.

User manual SNC-637ID

_________________________________________________________________________________

- 16 -

10) In case of installation without IP sharing device under Static IP, tick off Enable

DHCP .

11) Click „Submit‟ Button of [3-3] to save setting value.

12) Click „OK‟ upon appearing of IP Change Window of [3-4].

Pic 3 4 IP Change

13) Remove LAN Cable (Cross Cable) connected between SNC-637ID and PC.

14) Connect SNC-637ID to Network with LAN Cable (Straight Cable).

15) Connect PC to Network with LAN Cable (Straight Cable)..

16) Set up IP Address, Subnet Mask and Gate way of PC according to Network

environment.

17) Check

 Run WebBrowser on PC, input IP address set in SNC-637ID onto URLand

click Enter ,

 Check if IP Setting is correct or not, referring to Video Check

 In case Video is seen, SNC-637ID has been correctly set up.

 In case Video is not seen, check whether there may be confliction ofIP in

Network, and re-check the set value of Network environment of SNC-637ID,

and Network environment of User s PC.

User manual SNC-637ID

_________________________________________________________________________________

- 17 -

3.3 Installation with IP Sharing Device (Router)

1) After checking Video in 2. Installand Video Check , then go to the next step.

2) Connect SNC-637ID and PC with LAN Cable (Cross Cable).

3) Cable Connection and Network Setting should be done same as per 2.

Install and Video Check .

4) Go to Network Setting Page of Administrator‟s Page as per 4), 5), 6) of „Static IP

Setup‟.

5) InWAN Setting of [3-3], input IP Address, Subnet Mask, Gateway, HTTP Port

according to Network environment to connected SNC-637ID to.

6) For setting of DNS Server , input DNS Address to fit with Network Environment to

set. Use DNS value normally set in PC.

7) In case of installation without IP sharing device under Static IP, tick off Enable

DHCP . Click Submit Button of [3-6] to save the set value.

Pic. 3 5 Network Setting

8) Click OK upon appearing of IP Change Window of [3-10].

User manual SNC-637ID

_________________________________________________________________________________

- 18 -

Pic. 3 6 IP Change

9) It is connected to IP newly set up, in 20 seconds after window.

10) Check Video of SNC-637ID referring to 2. Install and Video Check as soon as it is

connected to IP newly set up.

11) Remove LAN Cable (Cross Cable) connected between SNC-637ID and PC.

12) Connect SNC-637ID to Network with LAN Cable (Straight Cable).

13) Connect PC to Network with LAN Cable (Straight Cable).

14) Port-Forward the port designated to use SNC-637ID, in IP Sharing Device. Refer

to manual of IP Sharing Device for details.

15) Check 1 (local check)

Run Web Browser and input IP address of SNC-637ID in URL and click „Enter‟. If

you changed HTTP Port, you must input http://IP Address:Port Number . For

example, If you set IP address of SNC-637ID to 192.168.10.88 and changed Web

Server port to 81, you must input http://192.168.10.88:81.

16) Check 2 (Check from outside)

After registration of SNC-637ID in Service Server (refer to Use of Service Server of

5. Basic Use, connect to SNC-637ID by Domain Name (Server Name) allocated to

SNC-637ID.

For example, run Web Browser and input Domain Name allocated to SNC-637ID in

URL. In http://IPDD6155SD.speco4u.net , IPDD6155SD is to be Name of Server

registered in Service Server by user.

If the initial page is shown, check Video of SNC-637ID referring to 2. Install and

Video Check . If Video is seen, set up is properly done.

User manual SNC-637ID

_________________________________________________________________________________

- 19 -

4. Expert Setting

After registration of SNC-637ID in Service Server (refer to Use of Service Server of 5.

Basic Use,connect to SNC-637ID by Domain Name (Server Name) allocated to SNC-637ID.

(For example, run Web Browser and input Domain Name allocated to SNC-637ID in URL. In

http://speco4u.net, SNC-637ID is to be Name of Server registered in Service Server by

user)

Click Administrators Pageon Initial Page of SNC-637ID, login Page of [4-1] appears.

Put admin in ID and Password line, click Login, then [4-2] Administrator's Page will be

shown. (ID, Password of SNC-637ID is preset as admin/9999 in Administrator s Page.

Change Administrator s ID and Password in General Setting of 4. Expert Setting. )

Pic. 4 2 Administrator‟s Page Login

User manual SNC-637ID

_________________________________________________________________________________

- 20 -

Pic. 4 3 Administrator s Page

Page is loading ...

Santec SNC-637ID User manual

Santec SNC-637ID User manual

Related papers

Other documents