2. PacLights
  3. BW027
BW027

PacLights BW027 Installation guide

  • Hello! I'm your chat assistant. I have reviewed the installation guide for the PacLights BW Series Generation 2 LED Light Bulbs, including models BW/2-012/018/027, BW/2-036/045/054/063, and BW/2-080/100/120. This document outlines the installation process, including the required ballast bypass for Metal Halide bulb replacements, and highlights optional features such as selectable color temperature and occupancy control. I'm ready to answer any questions you might have about these bulbs!
  • What should I do before installing the fixture?
    What is required when replacing a Metal Halide bulb?
    What function is available for select models?
INSTALLATION GUIDE BW Series Generation 2 LED Light Bulbs
Instructions and specifi cations are subject to change at any time without notice. Copyright© 2021 PacLights All Rights Reserved Page 1 of 2
Need help? (800) 988 -6386 Email: CS@PacLights.com Website: www.PacLights.com
PL-INST-BW/2-v0
BW/2 INITIAL SET-UP
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PacLights fi xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR
WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNINGS:
• Make certain power is OFF before installing or maintaining fi xture. No user serviceable parts inside.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sharp objects.
CAUTION:
• For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened fi rmly. Apply weatherproof silicone
sealant around the edge of the Back Box and/or Junction Box. This is especially important with an uneven wall surface. Silicone all plugs and
unused conduit entries.
FIG. 1 FIG. 2
BW/2-012/018/027 BW/2-036/045/054/063 BW/2-080/100/120
Remove the Compact Flourescent Light or Metal Halide bulb CCW (Fig. 1). For the CFL bulb, it is a direct replacement. For the Metal Halide bulb, it
requires the bypass of the Ballast, Capacitor, and Ignitor from the circuit. Refer to Wiring Diagram. If provided, use the Security Cable to fi x onto the BW/2
bulb Tab and at the other end, fi x the Hook onto the Shell (Fig. 2).
Please make sure to bypass the Ballast (along with the Ignitor and Capacitor) before installing the BW/2 LED bulb!
WIRING DIAGRAM
CARABINER
& CABLE
BW/2 BULB
BULB
TAB
L
NCFL
L
NBW/2
L
N
MH
VVVVVV
BW/2
SOCKET
HOOK
SHELL
BALLAST
CAPACITOR
IGNITOR
L
N
VVVVV
BYPASS BALLAST
BYPASS
CAPACITOR
BYPASS
IGNITOR
INSTALLATION GUIDE BW Series Generation 2 LED Light Bulbs
Instructions and specifi cations are subject to change at any time without notice. Copyright© 2021 PacLights All Rights Reserved Page 2 of 2
Need help? (800) 988 -6386 Email: CS@PacLights.com Website: www.PacLights.com
PL-INST-BW/2-v0
The Optional Occupancy Control is available for select models
(80W/100W/120W) of the BW/2 Series. The Auxiliary (AUX) Port is
underneath the Plug Cover. Unscrew the Plug Cover (Refer to Fig. 3).
If needed, use a fl athead screwdriver. The AUX Port is at the center of
the top of the BW/2 bulb next to the Switches (Fig. 6).
OPTIONAL FIELD-SELECTABLE CCT (Correlated
Color Temperature)
The Optional 3CCT Function is available for select models of the BW/2
Series. Use the Switch underneath the Plug Cover. Unscrew the Plug
Cover (Fig. 3). If needed, use a fl athead screwdriver. The CCT Switch
allows the user to choose a desired color temperature 3000K, 4000K,
5000K (Fig. 4). After selecting the Color Temperature the BW/2 bulb is
ready to install.
FIG. 3
WATTAGE
SWITCH
FIG. 5
CCT SWITCH
1
OPTIONAL OCCUPANCY CONTROL
FIG. 6
2
AUX PORT
MICROWAVE
MOTION
CONTROL
FIG. 7
Sensor Segemented Dimming is available when using either Optional
Sensor. Prior to installing the PIR (Passive Infrared) or Microwave
Motion Sensor, move the Wattage Switch to the fi xture’s highest
wattage (Refer to Fig. 5). Install the Microwave Motion Sensor or the
PIR by screwing into the AUX Port and tighten carefully (Fig. 7).
PLUG
COVER
The Optional Selectable Wattage is available for select models (27W
-120W) of the BW/2 Series. Use the Switch underneath the Plug Cover.
Unscrew the Plug Cover (Refer to Fig. 3). If needed, use a fl athead
screwdriver. Each of the select models have their own wattage range from
low-medium-high where the user can make a selection.
OPTIONAL SELECTABLE WATTAGE
FIG. 4
PIR
BW/2 BULB
AUX PORT
/