Atdec TH-1026-VTP User manual

Category
Flat panel wall mounts
Type
User manual

Atdec TH-1026-VTP is a flat-screen wall mount with tilt functionality, designed for displays with VESA mounting hole configurations of 75x75mm and 100x100mm. It supports a maximum load of 15kg (33lbs) and can be installed on either masonry or timber walls. The mount allows for -15° to +15° of tilt adjustment and +/- 30° of pan adjustment, providing optimal viewing angles. It comes with a range of hardware, including M4/M6 washers, S8 nylon anchors, M6x10mm/16mm screws, and a spanner for easy installation.

Atdec TH-1026-VTP is a flat-screen wall mount with tilt functionality, designed for displays with VESA mounting hole configurations of 75x75mm and 100x100mm. It supports a maximum load of 15kg (33lbs) and can be installed on either masonry or timber walls. The mount allows for -15° to +15° of tilt adjustment and +/- 30° of pan adjustment, providing optimal viewing angles. It comes with a range of hardware, including M4/M6 washers, S8 nylon anchors, M6x10mm/16mm screws, and a spanner for easy installation.

Installation Instructions
TH-1026-VTP
Component Checklist
Flat Screen Wall Mount | Tilt
Security
Screw (x2)
Spanner
M6 Coach
Bolt (x4)
S8 Nylon
Anchor (x4)
HARDWARE
Display Mounting
Screws (x4 each)
M4x10mm/16mm
M6x10mm/16mm
Tools Required:
Power Drill
4mm(0.15”) Drill Bit
8mm(0.3”) Masonry Drill Bit
Phillips head screw driver
17mm(0.7”) Socket Wrench or Shifter
! IMPORTANT - Install Telehook Flat Screen Wall Mount as per installation instruction.
! This product supports a maximum load of 15kg (33lbs.).
! This product support VESA Mounting Hole Configuratons: 75x75mm and 100x100mm.
Also supports 200x100mm via additional adaptor plate AC-AP-2010 (sold separately).
! The manufacturer accepts no responsibility for incorrect installation.
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received against the component checklist and hardware above.
M4/M6 Washer
(x4 each)
TH-1026-VTP
(fully assembled)
Step 2. Hardware to Masonary Wall
Timber StudMasonry Wall
3-5mm
Clearance
WALL
Coach Bolt
Coach Bolt
Nylon Anchor
Step 3b. Attach Wall Plate to Timber Wall
Ø4mm x 50mm deep
Drilled Hole
Ø8mm x 50mm deep
Drilled Hole
A. Attach TH-1026-VTP Wall Plate to the wall. B. Tighten the two coach bolts using the supplied spanner.
Supplied Spanner
TIGHTEN
OR
Step 3a. Hardware to Timber Wall
Tip: Use the TH-1026-VTP Wall Plate as a drilling template.
NOTE: Use a stud finder to accurately
locate the center of the stud. Ensure
that all screws fix securely into the stud.
Installation Complete
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 04.12.12 ©
Step 4. Remove Mounting Plate
PULL-OUT
Mounting Plate
Step 5. Attach Mounting Plate to the Display
TOP
Back of Display
Mounting
Plate
Washer
Display
Mounting
Screw
Step 6. Mount the Display to the Wall
INSERT
Mounting Plate with Display
Step 7. Fasten the Two Security Screws
FASTEN
Security Screw
Step 8. Tilt Adjustment Step 9. Pan Adjustment
+15°
-15°
LOOSEN
TIGHTEN
+30°
-30°
DISPLAY NOT SHOWN
DISPLAY NOT SHOWN
DISPLAY NOT SHOWNDISPLAY NOT SHOWN
  • Page 1 1
  • Page 2 2

Atdec TH-1026-VTP User manual

Category
Flat panel wall mounts
Type
User manual

Atdec TH-1026-VTP is a flat-screen wall mount with tilt functionality, designed for displays with VESA mounting hole configurations of 75x75mm and 100x100mm. It supports a maximum load of 15kg (33lbs) and can be installed on either masonry or timber walls. The mount allows for -15° to +15° of tilt adjustment and +/- 30° of pan adjustment, providing optimal viewing angles. It comes with a range of hardware, including M4/M6 washers, S8 nylon anchors, M6x10mm/16mm screws, and a spanner for easy installation.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI