USER GUIDE
Full Motion TV Wall Bracket
MODEL NUMBER: 20710
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Contents
1.
2.
3.
4.
5-11.
12.
13-14.
15.
Welcome Section
Information & Safety Instructions
Contents & Features
Pouch Part List
Installation
• Placing The Bracket
• Drilling (Brick Wall)
• Fitting The Plate
• Fitting The TV Mount
• Completing The Mount
Adjustments
• Adjusting The Viewing Angle
Alternative Installation
• Stud Wall
Specications
Copyright © 2019 Thunderbolt Photography, Richard Ross. All rights reserved.
All Photos and Illustrations may not be reproduced or used in any manner whatsoever without the
express written permission of the copyright holder.
Welcome Section
Congratulations!
You have made an excellent choice with the purchase of this quality
REKA
®
product.
By doing so you now have the assurance and peace of mind which
comes from purchasing a product that has been manufactured to
the highest standards of performance and safety, supported by the
high quality standards of Quesh Ltd.
We want you to be completely satised with your purchase, so this
REKA
®
product is backed by a comprehensive manufacturer’s
3 year warranty and outstanding after sales service through our
dedicated helpline.
We hope you enjoy using this product for many years to come.
If you require technical support or in the unlikely event that your
purchase is faulty, please telephone our helpline for immediate
assistance. Faulty product claims made within the 3 year warranty
period will be repaired or replaced free of charge provided that you
have a satisfactory proof of purchase (keep your receipt safe).
This does not affect your statutory rights. However be aware that the
warranty will become null and void if the product is found to have
been deliberately damaged, misused and/or disassembled.
1
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Information &
Safety Instructions
Additional Equipment Required (brick):
• Safety goggles
• Paper dust mask
• Safety step/work platform
• Masking or electrician tape
• Pencil
• 4mm or 5mm Masonry drill bit (Brick mounting only)
• 4mm or 5mm Twist drill bit (Stud mounting only)
• 10mm Masonry drill bit (Brick mounting only)
• 10mm Twist drill bit (Stud mounting only)
• Hammer action drill
• Hammer
• Large at head or pozidrive screwdriver
• 10mm Spanner or socket wrench
Keep the work environment trip and hazard free before beginning
and during installation.
Always refer to the manufacturers safety instructions and guides
before using power tools.
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
2
Contents & Features
3
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Contents
1 x Hinged Wall Mount
1 x Rear Plate
4 x VESA Mount Arms
4 x M6 x 55mm Coach Screw
4 x 10mmØ x 50mm Wall Plug
4 x 5mmØ Washer
8 x 6mmØ Washer
4 x 8mmØ Washer
4 x M4 x 14mm Screw
4 x M5 x 14mm Screw
4 x M6 x 14mm Screw
4 x M8 x 14mm Screw
4 x M6 x 12mm Bolt
4 x M6 Nut
1 x Cable Tie
1 x Mini Bubble Level
Features
• Mounts up to VESA 400mm x 400mm
• 180° Triple Articulated Arm
• Arm Reach 65mm to 420mm
• +5° to -15° Screen Tilt
• 30Kg Max load
• Cable tie
• Multi Position Arm Mounts
(VESA - Video Electronics Standards Association)
4
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Pouch Parts List
A B
C
WALL FITTINGS
M6 x 55mm Coach Screw
10mmØ x 50mm Wall Plug
6mmØ
Washer
G
F
D
E
H
I
J
VESA MOUNT FITTINGS
M4 x 14mm Screw
M5 x 14mm Screw
M6 x 14mm Screw
M8 x 14mm Screw
5mmØ x 14mm Washer
6mmØ x 14mm Washer
8mmØ x 14mm Washer
K
L
ARM FITTINGS
M6 x 12mm Bolt M6 Nut
5
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Installation
Place the mount over the centre mark. Take the bubble level, place
it on the top edge of the plate and adjust it until the bubble is rest-
ing in the middle of line marks. Once level mark the four corner
holes with a pencil being careful not to move the plate.
Alternatively you can trace the outline and holes of the plate on to
a blank piece of A4 paper. Level the drawn guide with the bubble
level and use that to guide you where to drill the holes.
Placing The Bracket
Test place the wall bracket around the room until you nd the best
suitable location for it, then draw a rough centre line on your
chosen location. Please take into consideration the size of the
TV/monitor for clearance as well as plug and aerial socket
placements. Be careful of pipes and electrical wiring before drilling.
6
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Installation
Drilling (Brick Wall)
After the drill hole placements have been marked, clear the work
area so it is safe to work in. Place dust sheets if required.
If the placement is above chest height you will need to use a safety
step or work platform to minimise risk of injury whilst using power
tools.
You will need to drill a smaller pilot hole before the larger 10mm
hole. This will minimise any possible damage and injury or
accidents.
Fit the 4mm or 5mm masonry drill bit to the hammer drill. Place the
wall plug next to the drill bit with the tips level. Wrap a little masking
or electricians tape about 5mm above the height of the wall plug.
This will mark the depth of how far you need to drill.
Next, t and mark the 10mm masonry drill bit in the same way as
previously mentioned and redrill the holes to the larger diameter.
7
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Installation
Fitting The Plate
First, place the wall plugs into the drilled holes and tap in gently
with a hammer to seat them ush to the wall.
Next insert the M6 x 55mm coach screws (pouch ‘A’) through the
6mmØ washers (pouch ‘C’) ready for use.
Line the holes of the plate to the drilled holes on the wall and insert
the screws. Tighten with a 10mm spanner or socket wrench until
securely tight.
B C A
8
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Installation
Once the plate has been securely tted, place the cover cap to hide
the bolts and neaten up the tting.
Safely secure power tools after you have nished drilling.
Brush and wipe down surfaces free of brick dust and hoover the
work area clean..
9
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Installation
Fitting The TV Mount
Check the TV/monitors mount placement holes. Once checked
place the arms in the correct orientation on the rear plate.
Secure the arm in place by inserting the M6 x12mm bolt (pouch
‘K’) through the arm’s square hole making sure the arm notch lines
up with the rear plate. Use the M6 nut (pouch ‘L’) to lock the arm in
place using 10mm spanner or socket wrench.
L
K
10
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Installation
With the TV facing down, being careful not to damage or scratch
the screen, place the rear mount into position, lining up with the
VESA mounting holes.
Check your TV instructions to nd out the correct size screws to
use to secure the rear plate in place. Use the correct sized screw
from pouch ‘I/J/K’ and the correct washer from pouch ‘D/E/F/J’
and tighten with a large at head or pozidrive screwdriver.
.
G H I J
D E F
11
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Installation
Completing The Mount
Remove the screws and washers from the rear plate bracket.
Lift the TV/monitor into place making sure the ‘V’ cut out on the
base of the rear plate bracket is resting on the side stanchions of
the wall arm.
Please Note: This process may require two people.
Refasten the screws and washer to secure the rear bracket to the
wall arm.
12
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Adjustments
Adjusting The Viewing Angle
Loosen the screws at where the rear mount attaches to the wall
arm. Tilt the screen in to the preferred position and tight the screws
again. Choose between the limits of +5° through to -15°
Move the three 180° joints to move the TV/monitor close or further
away from the wall as well as to adjust the screen facing direction.
13
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Alternate Installation
Stud Wall
Using a stud detector nd out where the wall studs are. Newer UK
builds typically have the studs placed 406mm (16”) approximately
apart, but they can be spaced up 609mm (24”) with an approximate
thickness of 36mm (1½”).
If you have a double stud you will be able to mount the bracket
on this without a bracket mount board. Mount in the same way as
listed on page 5 to 7, but instead of using a masonry drill bit, use a
twist drill bit (general purpose).
StudStud
Plasterboard
Bracket
Placement
Be careful of any wiring or pipes that maybe running through studs.
14
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Alternate Installation
If you don’t have a double stud you will need to make a mounting
board using marine ply or suitable material. Use the supplied wall
plugs and coach screws to hang the board. To x the bracket to the
plate you will need to use 4 x M6 nut and bolts with 8x washers.
Use a stud nder to nd the distance between the outer edges of
the studs. This will tell you the length of board you will need. The
height of the board should be 260mm. Use a twist drill bit to drill
the holes to mount the board to the studs, loosely secure in to
place as you will need to remove it after the next step.
Once the board is tted, place the bracket in to position and mark
the holes the same as page 5. Remove the board from the wall and
drill the placement holes for the bracket. You will need to
counter sink the rear holes to accommodate the washer diameter
and the depth of the bolt head. Put the bracket into place lining
up the holes. Put a washer on the M6 bolt and pass it through the
holes from the back. Place another washer on the end of the bolt
and tighten the nut. Once all four bolts have been tted, place the
completed mount on the wall and secure it tightly with the coach
screws.
Bracket
Placement
Mounting
Board
Stud
Stud
15
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Hereby, Quesh Ltd declares that this product is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address: www.quesh.co.uk
Specification
2.4Kg
70mm x 222mm
65mm to 420mm
30Kg
400mm x 400mm
General
Approx Weight:
Approx Mounting Plate Dimensions:
Approx Arm Reach:
Max Supported Weight:
Max VESA Size:
Full Motion TV Wall Bracket
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Warranty Certificate
Warranty
This product is warranted to be free from defects in workmanship and parts for a period of 36 months
from the date of purchase. Defects that occur within this warranty period, under normal use and care,
will be repaired, replaced or refunded at our discretion, solely at our option with no charge for parts and
labour. The benets covered by this warranty are in addition to all rights and remedies in respect of the
product the consumer has under existing U.K. laws.
Proof of Purchase
This warranty is valid for the original purchase and is not transferable.
Please keep your purchase receipt as proof of purchase (approved outlet) and as proof of the date of
when the purchase was made (start of warranty). The receipt must be presented with the warranty card
when making a claim under this warranty.
Service during the Warranty Period
Please ensure the product is properly packaged so as to ensure that no damage occurs in transit. Also
make sure that you have included a detailed explanation of the problem.
Extent of the Warranty
This warranty is limited to defects in workmanship or parts. All defective products or parts will be
repaired or replaced. This warranty does not extend to accessories.
Normal Wear and Tear
This warranty does not cover normal wear and tear of the product or parts.
Exclusions
This warranty does not cover the following:
• Any defect caused by accident, misuse, abuse, improper installation or operation, lack of reasonable
care, unauthorised modication, loss of parts, tampering or attempted repair by a person not
authorised by the distributor.
• Any product that has been damaged by lightning strike either directly or indirectly, or on a mains
or vehicle outlet power surge or liquid ingress.
• Any product that has not been installed, operated or maintained in accordance with the
manufacturer’s operating instructions provided with the product.
• Any product that has been used for purposes other than domestic use.
• The product if it is located outside of the U.K. and Ireland
• Any damage caused by improper power input or improper cable connection.
This warranty does not affect your statutory rights.
After Sales Support
UK/N.IRELAND HELPLINE N
O
:
REP.IRELAND HELPLINE N
O
:
WEBSITE:
EMAIL:
01270 508538
1800 995 036
www.quesh.co.uk
Warranty Service Address
QUESH LTD,
B7, FIRST BUSINESS PARK
FIRST AVENUE, CREWE, CHESHIRE.
CW1 6BG
Warranty Card
Full Motion TV Wall Bracket
Please keep your purchase receipt together with your warranty card
Fault Description:
Name:
Address:
Date of purchase:
Location of purchase:
We recommend that you attach a photocopy of your receipt, showing the date of purchase, to this
warranty card and keep it for your reference. In the event of a product fault, please call the After Sales
Support team. Please ensure that you have the product details (as shown on this card) to hand so that
the support team are able to respond as quickly and efciently as possible.
Model Number: 20710
Ofce Use:
Repaired Replaced Other
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
