Stovax RVACB100B User manual

Stovax
Brand
Stovax
Model
RVACB100B
Type
User manual

This manual is also suitable for

Riva Freestanding Bench
Installation Instructions
Product Codes: RVACB45B (For use with RVF40C)
RVACB100B (For use with RVF40C, RVF66 & RVF76)
RVACB120B (For use with RVF40C, RVF66 & RVF76)
PM205 ENG Issue 2 (August 2007)
IMPORTANT
Please read these instructions carefully and in conjunction with the appropriate Riva instructions.
Care must be taken when handling the stove to avoid injury or damage to the stove.
2
1. Position bench on your hearth and mark
out the 2 key slots on the floor.
2. Remove bench and drill the two marked
positions with Ø8mm hole to 50mm deep.
PR7582
Ø8mm
PR7583
3. Tap in No.8 Rawl plugs.
No8 rawl plug
Ø8mm hole
PR7584
4. Screw in No.8 coach bolt leaving 5mm gap
from the surface of the floor.
No8 Coach Bolt
5mm gap
PR7585
Packing list
• User Instructions
• 3 x Drilling Templates
• 4 x M6 x 90 Coach bolts
• 4 x M6 Washers
• 4 x M6 Nuts
• 2 x No.8 Hex Coach bolt
• 2 x Rawl plugs
• 5 x Felt pads
Tools required
• 10mm A/F Spanner
• 13mm A/F Spanner
• Hammer
• Center Punch
• Power Drill with:
• Ø8mm Masonry drill bit
• Ø8mm Steel drill bit
• Pozidrive attachment
ASSEMBLY INSTRUCTIONS
1
2
3
4
3
5. Slide The bench over the coach bolts and
tighten. Position drilling template as you would the
stove.
PR7569
6. Mark drilling points with a centre punch.
PR7570
7. Drill four Ø8mm holes. Straight through both
sides.
PR7571
8. Remove back cover plate from the stove.
PR7572
9. Lift off stove cover plate.
PR7573
10. Firstly remove all internal parts from the
stove and remove the door. Tip the stove onto its
front on a soft surface that will not damage the
paintwork. Apply felt pads to each corner of the
base.
PR7574
Felt pads
ASSEMBLY INSTRUCTIONS
5
6
7
8
9
10
PR7580
Stovax Ltd, Falcon Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7LF
Tel: (01392) 474011 Fax: (01392) 219932 E-mail: [email protected] www.stovax.com
13. Repeat step 12 with the rear holes.
PR7577
14. Replace the top cover plate.
PR7578
15. Re-attach the back cover plate, internal parts
and door.
PR7579
12 Remove ash pan and insert the two coach
bolts in the front holes, fixing with the nuts and
washers provided.
PR7576
M6 X 90mm coach bolt
M6 nut
M6 washer
11. Position the stove onto the bench.
PR7575
ASSEMBLY INSTRUCTIONS
12
11
14
15
16
13
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Stovax RVACB100B User manual

Stovax
Brand
Stovax
Model
RVACB100B
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents