Atdec TH-3060-UFH User manual
- Category
- Flat panel wall mounts
- Type
- User manual
The Atdec TH-3060-UFH is a full-motion TV wall mount designed for large to medium-sized TVs. It supports VESA mounting hole configurations from 200mm x 200mm to 400mm x 400mm and can hold TVs weighing up to 35kg (77lbs). The mount features a unique locking mechanism that automatically locks the arm in position when pushed up against the wall, making it easy to install and use. Additionally, the mount has four optional arm positions, allowing you to customize the viewing angle of your TV.
The Atdec TH-3060-UFH is a full-motion TV wall mount designed for large to medium-sized TVs. It supports VESA mounting hole configurations from 200mm x 200mm to 400mm x 400mm and can hold TVs weighing up to 35kg (77lbs). The mount features a unique locking mechanism that automatically locks the arm in position when pushed up against the wall, making it easy to install and use. Additionally, the mount has four optional arm positions, allowing you to customize the viewing angle of your TV.
Component Checklist
Coach Screw (x4)
Nylon Anchor (x4)
Washer (x4)
5mm/4mm
Allen Key
M6x16mm
M6x25mm
M8x16mm
M8x25mm
Installation Instructions
TH-3060-UFL
Large-Medium TV Articulated Arm
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
! IMPORTANT - Install Telehook 3060 Large-Medium TV Articulated Arm per Installation Instructions.
! This product supports a maximum load of 35kg (77lbs).
! This product supports VESA mounting hole configurations 200mm wide x100mm high to 700mm wide x 500mm high.
! The manufacturer accepts no responsibility for incorrect installation.
Display Mounting
Screws (x4 each)
Hardware
Tools Required:
Power drill
•
5mm (0.2”) drill bit
•
10mm (0.39”) masonry drill bit
•
Phillips head screw driver•
13mm (0.5”) socket wrench or shifter
•
Step 2. Changing position of Arm on Wall Mount
Step 3. Install Arm/Wall Mount to the Wall
Arm/Wall Mount
Mounting Bracket (x2)
Multiwasher (x4)
End Cap (x2)
Top Cap (x2)
Block (x2)
Locking
Screw (x4)
End Cap
Use Phillips head screw driver
to loosen and tighten.
Use 5mm Allen Key to
loosen and tighten.
Timber Stud Wall
Masonry Wall
- Drill four 10mm (0.39”) diameter holes, 58mm (2.3”) deep.
- Secure the mounting plate to the wall using the Coach
Screws and Nylon Anchors supplied.
- Drill four 5mm (0.2”) diameter holes, 58mm (2.3”) deep.
- Secure the mounting plate to the wall using the Coach
Screws supplied.
NOTE: Use a stud finder to accurately locate the centre
of the stud. Ensure that all screws fix securely into stud.
Four optional positions
OR
Coach Screw
Washer
End Cap
Screw
Nylon Anchor
Drilled Hole
End Cap
Coach Screw
Washer
End Cap
Screw
Drilled Hole
End Cap
WALL
WALL
Component Checklist
Coach Screw (x4)
Nylon Anchor (x4)
Washer (x4)
5mm/4mm
Allen Key
M6x16mm
M6x25mm
M8x16mm
M8x25mm
Installation Instructions
TH-3060-UFL
Large-Medium TV Articulated Arm
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
! IMPORTANT - Install Telehook 3060 Large-Medium TV Articulated Arm per Installation Instructions.
! This product supports a maximum load of 35kg (77lbs).
! This product supports VESA mounting hole configurations 200mm wide x100mm high to 700mm wide x 500mm high.
! The manufacturer accepts no responsibility for incorrect installation.
Display Mounting
Screws (x4 each)
Hardware
Tools Required:
Power drill
•
5mm (0.2”) drill bit
•
10mm (0.39”) masonry drill bit
•
Phillips head screw driver•
13mm (0.5”) socket wrench or shifter
•
Step 2. Changing position of Arm on Wall Mount
Step 3. Install Arm/Wall Mount to the Wall
Arm/Wall Mount
Mounting Bracket (x2)
Multiwasher (x4)
End Cap (x2)
Top Cap (x2)
Block (x2)
Locking
Screw (x4)
End Cap
Use Phillips head screw driver
to loosen and tighten.
Use 5mm Allen Key to
loosen and tighten.
Timber Stud Wall
Masonry Wall
- Drill four 10mm (0.39”) diameter holes, 58mm (2.3”) deep.
- Secure the mounting plate to the wall using the Coach
Screws and Nylon Anchors supplied.
- Drill four 5mm (0.2”) diameter holes, 58mm (2.3”) deep.
- Secure the mounting plate to the wall using the Coach
Screws supplied.
NOTE: Use a stud finder to accurately locate the centre
of the stud. Ensure that all screws fix securely into stud.
Four optional positions
OR
Coach Screw
Washer
End Cap
Screw
Nylon Anchor
Drilled Hole
End Cap
Coach Screw
Washer
End Cap
Screw
Drilled Hole
End Cap
WALL
WALL
Component Checklist
Coach Screw (x4)
Nylon Anchor (x4)
Washer (x4)
5mm/4mm
Allen Key
M6x16mm
M6x25mm
M8x16mm
M8x25mm
Installation Instructions
TH-3060-UFL
Large-Medium TV Articulated Arm
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
! IMPORTANT - Install Telehook 3060 Large-Medium TV Articulated Arm per Installation Instructions.
! This product supports a maximum load of 35kg (77lbs).
! This product supports VESA mounting hole configurations 200mm wide x100mm high to 700mm wide x 500mm high.
! The manufacturer accepts no responsibility for incorrect installation.
Display Mounting
Screws (x4 each)
Hardware
Tools Required:
Power drill
•
5mm (0.2”) drill bit
•
10mm (0.39”) masonry drill bit
•
Phillips head screw driver•
13mm (0.5”) socket wrench or shifter
•
Step 2. Changing position of Arm on Wall Mount
Step 3. Install Arm/Wall Mount to the Wall
Arm/Wall Mount
Mounting Bracket (x2)
Multiwasher (x4)
End Cap (x2)
Top Cap (x2)
Block (x2)
Locking
Screw (x4)
End Cap
Use Phillips head screw driver
to loosen and tighten.
Use 5mm Allen Key to
loosen and tighten.
Timber Stud Wall
Masonry Wall
- Drill four 10mm (0.39”) diameter holes, 58mm (2.3”) deep.
- Secure the mounting plate to the wall using the Coach
Screws and Nylon Anchors supplied.
- Drill four 5mm (0.2”) diameter holes, 58mm (2.3”) deep.
- Secure the mounting plate to the wall using the Coach
Screws supplied.
NOTE: Use a stud finder to accurately locate the centre
of the stud. Ensure that all screws fix securely into stud.
Four optional positions
OR
Coach Screw
Washer
End Cap
Screw
Nylon Anchor
Drilled Hole
End Cap
Coach Screw
Washer
End Cap
Screw
Drilled Hole
End Cap
WALL
WALL
Component Checklist
Coach Screw (x4)
Nylon Anchor (x4)
Washer (x4)
5mm/4mm
Allen Key
M6x16mm
M6x25mm
M8x16mm
M8x25mm
Installation Instructions
TH-3060-UFL
Large-Medium TV Articulated Arm
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
! IMPORTANT - Install Telehook 3060 Large-Medium TV Articulated Arm per Installation Instructions.
! This product supports a maximum load of 35kg (77lbs).
! This product supports VESA mounting hole configurations 200mm wide x100mm high to 700mm wide x 500mm high.
! The manufacturer accepts no responsibility for incorrect installation.
Display Mounting
Screws (x4 each)
Hardware
Tools Required:
Power drill
•
5mm (0.2”) drill bit
•
10mm (0.39”) masonry drill bit
•
Phillips head screw driver•
13mm (0.5”) socket wrench or shifter
•
Step 2. Changing position of Arm on Wall Mount
Step 3. Install Arm/Wall Mount to the Wall
Arm/Wall Mount
Mounting Bracket (x2)
Multiwasher (x4)
End Cap (x2)
Top Cap (x2)
Block (x2)
Locking
Screw (x4)
End Cap
Use Phillips head screw driver
to loosen and tighten.
Use 5mm Allen Key to
loosen and tighten.
Timber Stud Wall
Masonry Wall
- Drill four 10mm (0.39”) diameter holes, 58mm (2.3”) deep.
- Secure the mounting plate to the wall using the Coach
Screws and Nylon Anchors supplied.
- Drill four 5mm (0.2”) diameter holes, 58mm (2.3”) deep.
- Secure the mounting plate to the wall using the Coach
Screws supplied.
NOTE: Use a stud finder to accurately locate the centre
of the stud. Ensure that all screws fix securely into stud.
Four optional positions
OR
Coach Screw
Washer
End Cap
Screw
Nylon Anchor
Drilled Hole
End Cap
Coach Screw
Washer
End Cap
Screw
Drilled Hole
End Cap
WALL
WALL
Component Checklist
Coach Screw (x4)
Nylon Anchor (x4)
Washer (x4)
5mm/4mm
Allen Key
M6x16mm
M6x25mm
M8x16mm
M8x25mm
Installation Instructions
TH-3060-UFL
Large-Medium TV Articulated Arm
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
! IMPORTANT - Install Telehook 3060 Large-Medium TV Articulated Arm per Installation Instructions.
! This product supports a maximum load of 35kg (77lbs).
! This product supports VESA mounting hole configurations 200mm wide x100mm high to 700mm wide x 500mm high.
! The manufacturer accepts no responsibility for incorrect installation.
Display Mounting
Screws (x4 each)
Hardware
Tools Required:
Power drill
•
5mm (0.2”) drill bit
•
10mm (0.39”) masonry drill bit
•
Phillips head screw driver•
13mm (0.5”) socket wrench or shifter
•
Step 2. Changing position of Arm on Wall Mount
Step 3. Install Arm/Wall Mount to the Wall
Arm/Wall Mount
Mounting Bracket (x2)
Multiwasher (x4)
End Cap (x2)
Top Cap (x2)
Block (x2)
Locking
Screw (x4)
End Cap
Use Phillips head screw driver
to loosen and tighten.
Use 5mm Allen Key to
loosen and tighten.
Timber Stud Wall
Masonry Wall
- Drill four 10mm (0.39”) diameter holes, 58mm (2.3”) deep.
- Secure the mounting plate to the wall using the Coach
Screws and Nylon Anchors supplied.
- Drill four 5mm (0.2”) diameter holes, 58mm (2.3”) deep.
- Secure the mounting plate to the wall using the Coach
Screws supplied.
NOTE: Use a stud finder to accurately locate the centre
of the stud. Ensure that all screws fix securely into stud.
Four optional positions
OR
Coach Screw
Washer
End Cap
Screw
Nylon Anchor
Drilled Hole
End Cap
Coach Screw
Washer
End Cap
Screw
Drilled Hole
End Cap
WALL
WALL
Flat screen wall mount | Full Motion height adjustable
TH-3060-UFH
! IMPORTANT - Install Telehook Flatscreen wall mount as per Installation Instructions
! This product supports a minimum load of 5kg (11lbs) and a maximum load of 25kg (55lbs)
! This product supports VESA mounting hole configurations from 200mm x 200mm to 400mm x 400mm
! The Manufacturer accepts no responsibility for incorrect installation.
Check you have received all parts against the Component Checklist and Hardware.
M6 x 16mm (x4)
M6 x 25mm (x4)
Display Mounting
Screws Bag
M8 x 16mm (x4)
M8 x 25mm (x4)
Hardware Bag
Coach Screw (x4)
Nylon Anchor (x4)
Spanner
6mm/4mm
Allen key
20mm Washer (x4)
Arm
Display
Mount
Mount
cap (x2)
Display
Bracket (x2)
Wall plate
cover (x2)
Masonary Wall Timber Stud wall
- Using a 10mm (0.39”) masonary drill bit, Drill four holes,
60mm (2.4”) deep.
- Secure the mounting plate to the wall using the Coach
Screws and Nylon Anchors supplied.
- 5mm (0.2”) drill bit
- 10mm (0.39”) masonary drill bit
- Philips head screwdriver
- Power drill
Tools required:
Clearance
locked position
free movement
M6 Nyloc Nut (x4)
M6 x 6mm screw (x4)
12mm Washer (x4)
Installation Instructions
- Using a 5mm (0.2”) drill bit, Drill three holes , 60mm (2.4”)
deep.
- Secure the mounting plate to the wall using the Coach
Screws supplied.
NOTE: Use a stud finder to accurately locate the centre
of the stud. Ensure that all screws fix securely into stud.
Coach Screw
Washer
Nylon Anchor
Drilled hole
Coach Screw
Washer
Drilled hole
This product has a feature where the arm will automatically lock in position when
pushed up against the wall to the left. If this feature is to be used allow clearance
to the left when deciding the mounting location.
To unlock, pull the chord down whilst
moving the arm away from the wall
Wall
Wall
Step 3. Install Arm to the wall
Step 1. Check Components
Component Checklist
Step 2. Mounting Location
IMPORTANT INFORMATION
PUSH
Flat screen wall mount | Full Motion height adjustable
PUSH
5° 5°
x2
The Mounting rails support VESA hole
configurations from 200mm x 200mm to
400mm x 400mm
Display mounting screw
Only insert the M6 x 6mm screws in
the mounting rail attached to the top of
the display. Tighten fully then undo one
half turn
Mounting rail
Mount
Washer
M6 Nyloc Nut
(tighten firmly)
Threaded stud
A.From the
tightened position
undo each nut a
quarter of a turn two
times
B.This will
allow 10°
Horizontal
rotation
adjustment
Note:The nuts can be re-tightened to
secure the display in position or left to allow
future changes
Step4.AttachWallPlateCovers
Step6.HorizontalRotationAdjustment
Step8.AttachMountingRailsToDisplay
Step7.AttachScrewCovers
Step5.AttachDisplayMounttoArm
A.Prior to attaching your Display check which of the three pairs
of keyhole mounting positions on the Display Mount to use that
will also allow access to the lower mounting slots.
C.Attach M6 x 6mm screws
to the lower mounting rail, to
secure the display
If the Display drops down the spring
tension will need to be increased
If the Display rises the spring tension
will need to be decreased
B.To adjust the tension use
the supplied 6mm Allen Key
More tension for
heavier displays
less tension for
lighter displays
13°
loosen the nuts on both sides
of the tilt mount
Adjust the Display to the
desired viewing angle
Tighten nuts to secure position
keyholes
screws
Wall
Wall
A.The Arm may need to be adjusted to
suit the weight of the display
B.Hook the screws in the top mounting
bracket into your chosen
pair of keyhole
mounting
positions on the
display mount
Turn left nut
Anti-clockwise
Nuts
Turn right nut
Clockwise
Nuts
Turn right nut
Anti-clockwise
Turn left nut
Clockwise
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to the continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 07.09.12 ©
Step9.AttachDisplaytoDisplayMount
Step10.DisplayHeightAdjustment
Step11.TiltAdjustment
Installationcomplete
-
1
-
2
-
3
Atdec TH-3060-UFH User manual
- Category
- Flat panel wall mounts
- Type
- User manual
The Atdec TH-3060-UFH is a full-motion TV wall mount designed for large to medium-sized TVs. It supports VESA mounting hole configurations from 200mm x 200mm to 400mm x 400mm and can hold TVs weighing up to 35kg (77lbs). The mount features a unique locking mechanism that automatically locks the arm in position when pushed up against the wall, making it easy to install and use. Additionally, the mount has four optional arm positions, allowing you to customize the viewing angle of your TV.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Atdec TH-3060-LPF Installation guide
-
-
-
-
-
Atdec TH-2050-UFL Installation guide
-
-
Atdec TH-3060-UT User manual
-
-
Atdec TH-3270-UFM Installation guide
