One Stop Gardens 90601 Assembly & Operating Instructions

Brand: One Stop Gardens

Model: 90601

Type: Assembly & Operating Instructions

90601

PARK BENCH

WITH EAGLE DESIGN

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web Site at www.harborfreight.com

2004 by Harbor Freight Tools

any artwork contained herein may be reproduced in any shape or form without the

express written consent of Harbor Freight Tools.

For technical questions and replacement parts please call 1-800-444-3353.

ASSEMBLY & OPERATING INSTRUCTIONS

THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please

complete the owner’s record below:

Model

______________ Serial No._____________ Purchase Date_______________

SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the

entire manual to become familiar with the unit BEFORE you begin assembly.

Technical Specifications

Construction: Oak Wood with Teak oiled finish, Cast Iron material

Overall Dimensions: 49.6” L x 24” W x 28” H

Back Rest: 48-3/8” l X 17-1/2” H

Seat to Ground: 15”

Weight Capacity; 300 LBS, evenly distributed

Weight: 79.36 LBS.

Safety Warnings and Precautions

WARNING: When using product, basic safety precautions should always be followed to

reduce the risk of personal injury and damage to equipment.

Read all instructions before using this product!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Keep work area well lighted.

3. Store idle equipment. When not in use, products must be stored in a dry location to inhibit

damage from moisture and salt air.

4. Check for damaged parts. Before using any product, any part that appears damaged should

be carefully checked to determine that it will operate properly and perform its intended

function. Check for any broken or damaged parts and any other conditions that may affect its

operation. Check wood for any stains or flaws. Replace or repair damaged or worn parts

immediately.

5. Replacement parts and accessories. When servicing, use only identical replacement parts.

Use of any other parts will void the warranty.

6. Do not exceed the maximum weight capacity.

7. Use eye and ear protection. Always wear ANSI approved impact safety goggles when

assembling this product.

8. Make certain to set the Bench on a flat, even and solid surface.

9. Wear gloves and avoid sharp edges when assembling.

10. Always check hardware and assembled parts after assembling. All connections should

be tight and hardware tightened. We recommend assembling the Bench outdoors.

11. Do not allow children to play on, stand upon or climb on the Bench.

SKU 90601 Page 2

Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot

cover all possible conditions and situations that may occur. It must be understood by

the operator that common sense and caution are factors which cannot be built into

this product, but must be

supplied by the operator.

Assembly

Your Park Bench will require complete assembly prior to use. It is important that you read the

entire manual to become familiar with the product BEFORE you use the Park Bench. Before

assembling the Park Bench be sure that you have all parts described in the Parts List and

Assembly Diagram located on the last pages of this manual.

1. Set both Cast Iron Sides (5) down on your work surface. Each Cast Iron Side (5) has

5 tabs for the Seat Slats (8). Make certain that these tabs face inward-see Figure 1.

Figure 1

2. Set each of the four (4) similar Seat Slats (8) on top of corresponding tabs on each

Cast Iron Side (5). The fifth Seat Slat (8) has a rounded edge. Make certain to

place this Seat Slat (8) farthest from the back of the Bench. This is the Seat Slat (8)

that your knee bends over when you are sitting on the Bench.

3. Insert a Brass Bolt (7) down through the Seat Slat (8) and tab and thread on Nut (7).

Repeat for the remaining tabs.

4. Attach the Slat Brace (6) to all five (5) Seat Slats (8). Measure out to the

center of the Seat Slats and make a mark. Pilot holes will have to be drilled

(recommended 5/32” diameter) into the underside of the Seat Slats (8).

Warning: Do not drill through the slat, drill only deep enought to insert the screws.

Place the Slat Brace (6) so that it intersects the five Seat Slats (8) as in Figure 2.

Secure the Slat Brace (6) in place with five Wood Screws (9).

5. Find the Backside Top Slat (2), which has a rounded edge, and has pilot holes

drilled for inserting the Cast Iron Backrest (1). Position this slat with the rounded

edge up and toward the front, and the pilot holes toward the rear. Install it using

Brass Bolts and Nuts (7), in the same way as the Seat Slats (8).

6. Find the Backside Bottom Slat (3), and install it with the pilot holes on the

upper rear edge. Install it with Brass Bolts and Nuts (7).

NOTE: Do not fully tighten all hardware until assembly is completed.

SKU 90601 Page 3

Cast Iron Side (5)

tab

Seat Slat (8)

7. Lay the Park Bench forward, with the back of the backrest facing upward. Place the Cast Iron

Backrest (1) into the back, with the flanges contacting the top and bottom backside slats.

Check to be sure the pilot holes in the backside slats are aligned with the holes in the flanges

of the Cast Iron Backrest (1). If they are not, we recommend that you drill pilot holes for the

Wood Screws(9).

WARNING: Do not drill through the slat, drill only deep enough to insert the screws.

8. Install the Wood Screws (9) through the flanges in the Cast Iron Backrest (1) into the

Backside Top Slat (2) and Backside Bottom Slat (3). Set the bench upright.

9. Press the short Side Slats (4) into the back, on each side of the Cast Iron Backrest (1). Be

sure to align the recessed cut-outs with the flanges on the sides of the Cast Iron Backrest (1).

Secure these side slats in place with the remaining Wood Screws (9).

10. Place the Park Bench upright. Make certain that the Cast Iron Sides (5) are at

right angles to the floor and that the Seat Slats (8) are straight. Securely

tighten all hardware.

Maintenance

1. Keep the park bench wiped down and clean. If it is exposed to prolonged wet or corrosive

conditions, you may have to clean it thoroughly and apply a waterproofing sealer.

2. Do not use solvents or flammable materials to clean this park bench. A mild detergent in

water will be sufficient. Solvents may damage the paint; and possibly create fire hazard.

Unpacking

When unpacking your Park Bench with Eagle Design, check to make sure the following parts are

included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at

1-800-444-3353.

Part # Description Quantity Part # Description Quantity

1 Cast Iron Backrest 1 6 Slat Brace 1

2 Backside Top Slat 1 7 Brass Bolts and Nuts 14

3 Backside Bottom Slat 1 8 Seat Slat 5

4 Side Slat 2 9 Wood Screws 18

5 Cast Iron Side 2

SKU 90601 Page 4

Seat Brace (6)

Seat Slat (8)

Figure 2

Note: Some parts are listed and shown for illustration purposes only and are not available

individually as replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL

ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO

THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO

REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT

ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT

BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL

PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER

INSTALLATION OF REPLACEMENT PARTS THERETO.

Assembly/Parts Diagram

SKU 90601 Page 5

6 (see Figure 2)

One Stop Gardens 90601 Assembly & Operating Instructions

One Stop Gardens 90601 Assembly & Operating Instructions

One Stop Gardens 90601 Assembly & Operating Instructions

Related papers

Other documents