INSTRUCTION MANUAL SKU#272-0618 CLASSIC OUTDOOR BENCH
CAUTION: Read all instructions before assembly. Failure to do so may result in faulty assembly and potential injury.
SPECIAL WARNINGS: Assemble on a soft, non-abrasive surface, such as carpet or cardboard to avoid damaging the item.
Noted: Identify all parts packed in carton against the parts list. Remove all the protective material carefully and DO NOT use
a knife to prevent scratching the surfaces. USE ONLY ON LEVEL SURFACES. INSPECT VISUALLY BEFORE EACH USE AND
ENSURE ALL HARDWARE IS PROPERLY TIGHTENED.
CUSTOMER SERVICE: For questions, assistance or repair parts, please call toll free at: 1-800-505-8305 (M-F
8:00am-8:00pm) or visit us on the web www.americancustomerservice.com 24 hours a day.
PARTS LIST
REF.
PARTS NAME
IMAGE
PART#
QTY
A
Right Leg
53DU-A
1
B
Left Leg
53DU-B
1
C
Back
53DU-C
1
D
Seat Slat
53DU-D
5
E
Side Brace
53DU-E
2
F
Seat Brace
53DU-F
1
G
M6*30mm Screw
53DU-G
14
H
M6*20mm Screw
53DU-H
2
I
M6*12mm Washer
53DU-I
14
J
M6*16mm Washer
53DU-J
2
K
M6 Nut
53DU-K
16
L
M5*15 Screw
53DU-L
7
M
Plastic Cap
53DU-M
4
For missing parts, please call toll free
customer service number for further
assistance.
ASSEMBLY INSTRUCTIONS
STEP ONE:
With help of one other person, carefully hold Back (C) in place
Insert a M6*30mm Screw (G) through both the top and bottom hole of
the Back (C), Right Leg (A), then secure using 12mm Washer (I), Nut (K).
Place Plastic Cap (M) over Nut (K).
Repeat for Left Leg (B)
STEP TWO:
Using 2 M6*30mm Screws (G), insert through both ends of Seat Slat (D)
and into the backmost holes of Legs (A,B)
Secure with 12mm Washers (I) and Nut (K).
Repeat for remaining 4 Seat Slats (D), working from back to front.
STEP THREE:
With the help of one other person, place the bench on its side.
Secure Side Brace (E) to underside of Right Leg (A). Insert a M6*20mm
Screw (H) through 16mm Washer (J), Right Leg (A), Side Brace (E), and
secure using Nut (K).
Secure Side Brace (E) to underside of Seat Slat (D) using M5*15 Screw (L)
Repeat for Left Leg (B)
STEP FOUR:
Secure Seat Brace (F) to underside of Seat Slat (D) using M5*15 Screws
(L)
STEP FIVE:
Make sure all screws are securely tightened.
With the help of one other person, flip the bench upright.
Now your bench is ready to use!
BACKYARD CREATIONS® MANUFACTURER‘S WARRANTY (Limited 1-Year Warranty)
This product is covered under the manufacturer’s one year limited warranty against defects in workmanship and materials. If your
product fails structurally during normal use within one year of purchase, the manufacturer will repair or replace the defective unit at no
charge. The warranty excludes furniture used for commercial purposes, furniture damaged by act of nature, abuse or lack of proper
care or corrosion or rusting of metal frame and hardware. Proof of purchase (dated register receipt) and in some cases photos of the
product are required for warranty claims. Maintain your outdoor furniture by using furniture covers and store away during extreme
weather conditions.
SAVE YOUR RECEIPTS. THIS WARRANTY IS VOID WITHOUT THEM.
Test Rite Products Corp. 1900 S. Burgundy Place, Ontario, CA 91761 Made in China
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Shine Company 4205WT Operating instructions
-
Astonica 50107973 User manual
-
-
-
-
Image IMBE53901 User manual
-
Image Home Gym IMBE53900 User manual
-
Body-Solid SBL460P4 Assembly Manual
-
Other Argos Home Wooden 4 Seater Picnic Bench User manual
-
Image Home Gym IMBE53991 User manual
