One Stop Gardens 90352 Assembly Instructions Manual

Brand: One Stop Gardens

Model: 90352

Type: Assembly Instructions Manual

GLIDER

Two Seat with Cushions

ASSEMBLY INSTRUCTIONS

®.

any artwork contained herein may be reproduced in any shape or form without the express

written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

SPECIFICATIONS

SAVE THIS MANUAL

You will need the manual for the safety warnings and precautions, assembly instruc-

tions, operating and maintenance procedures, parts list and diagram. Keep your invoice

with this manual. Write the invoice number on the inside of the front cover. Keep the

manual and invoice in a safe and dry place for future reference.

SAFETY WARNINGS AND PRECAUTIONS

1. KEEP PRODUCT USAGE AREA CLEAN. Cluttered areas invite injuries. Place

product on flat, level surface such as carpet or grass. Concrete could injure people if

Glider is tipped over.

2. KEEP CHILDREN AWAY FROM PRODUCT DURING ASSEMBLY. Two adults are

better at assembling this product. Do not allow children to use until all hardware in this

product is fully assembled and tightened. Be careful not to pinch fingers when Glider is

in motion.

3. DO NOT ATTEMPT TO ASSEMBLE THIS PRODUCT IF UNDER THE INFLUENCE OF

ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your

judgement or reflexes are impaired while taking drugs. If there is any doubt, do not

attempt to assemble this product.

4. USE EYE PROTECTION. Wear ANSI approved safety impact goggles when

assembling this product. Goggles are available from Harbor Freight Tools.

5. PERIODICALLY CHECK. Check bolts and nuts to be sure hardware has not loosened.

6. STAY ALERT. Watch what you are doing at all times. Use common sense. Do not

assemble this product when you are tired or distracted from the job at hand.

7. CHECK FOR DAMAGE PARTS. Before using this product, carefully check that it will

operate properly and perform its intended function. Check for damaged parts and any

other conditions that may affect its operation. Replace or repair damaged or worn parts

immediately.

ITEM DESCRIPTION

Construction Cast-Iron Frame w/Light Brown Finish

Finish Slats Vinyl

Cushion Design Green Stripes w/Brown Background (2)

Overall Dimensions 44-1/8”L x 36”H

Weight 34.90 Lbs.

Weight Capacity 260 Lbs.

SKU 90352 PAGE 2

8. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical

replacement parts. Only use accessories intended for use with this product. Approved

accessories are available from Harbor Freight Tools.

9. THIS PRODUCT IS MANUFACTURED OF CAST IRON. Do not force any part of the

assembly and do not overtighten the bolts. Serious damage can occur. Do not stand

on Glider. Use only for intended purpose. The Glider is made for adults. Children need

to be supervised. Injury could occur if Glider is overloaded. Use caution!

10. RECOMMENDED AGE APPROPRIATE USE over 10 years of age unless

accompanied by an adult. Maximum weight capacity for Glider is 260 lbs.

UNPACKING

When unpacking, check to make sure all parts shown on the Parts List (page 5) are included.

If any parts are missing or broken, please call Harbor Freight Tools at the number shown on

the cover of this manual as soon as possible.

ASSEMBLY INSTRUCTIONS

We suggest you assemble the unit on a soft surface to avoid damage to the finish.

GLIDER

A smooth, relaxing and totally comfortable Glider with two soft thick Cushions. The Glider has

protective tan colored paint on the cast iron tubing and the Cushions are weather proof.

ASSEMBLY OF BENCH

1. Assemble the Glider frame by using the Hardware (A-D). The Armrests (#2) are

attached to the Ground Supports (#1), (Right and Left). The Backrest Frame (#9) and

Seat Frame (#10) are assembled to the Armrests (#2) and Ground Support (#1).

Carefully adjust the Seat Support Bar (#11) so that it fits and adds support between the

two assembled Armrests (#2) of the Glider. Tighten the hardware. See Figure 1 and 2.

Backrest

Frame

#11

Seat

Support Bar

#11

Seat

Support Bar

Backrest

Frame

#10

Seat Frame

Armrest

Ground

Support

Figure 1 Figure 2

SKU 90352 PAGE 3

3. After the Glider Frame is assembled you can attach the Glider Supports (#6). This lets

the Glider slide back and forth on the frame. See Figure 3.

4. Before putting the Cushions (#5) on, wrap the Back Vinyl Support Slates (#3) twice

around the Glider Back Rest Frame (#9) as shown in Figure 4. Match up the holes

drilled into the Back Rest Support. Use the hardware provided and tighten screw with

screw driver into the Back Rest Frame (#9). Stretch that Slat and wind it around twice

the corresponding hole in the Backrest Support Bar (#11), being sure the Vinyl Slates

are taught. Be sure Vinyl Support Slates are pulled tightly to prevent sagging. Repeat

across the total Back Rest Frame (#9) of the Glider. See Figure 4.

5. Wrap the Seat Vinyl Support Slates (#3) around the Glider Seat Frame (#10) and the

Seat Support Bar (#11). Match up the holes drilled into the Back Support. Use the

hardware provided and tighten screws with screw driver. Be sure Vinyl Support Slates

are pulled tightly to prevent sagging. Repeat across the Seat Frame (#10).

See Figure 5.

6. When assembly is finished, loosen all nuts and bolts, (not the Vinyl Slat Screws)

align the swing to cradle as square as possible and proceed to tighten all the nuts and

bolts once it is aligned.

Note: It may become necessary to enlarge the holes in the Cast Iron pieces of the Frame and

Armrests. Clear the hole of paint by sliding a bolt through the hole or using a drill.

Warning: Do not force components and overtighten the nuts during assembling.

Assembled

Glider Frame

#1 Ground

Support

#6 Glider

Supports

Armrest

Vinyl

Support

Slates

#9 Back

Rest Frame

#11

Backrest &

Seat Support Bar

Vinyl

Support

Slates

#10

Seat

Frame

Figure 3

Figure 4

Figure 5

SKU 90352 PAGE 4

CARE AND MAINTENANCE

Cushions Covers

Use a mild mix of soap and water. Wipe cushions down with a sponge and towel dry.

Allow to air dry. Be sure to not machine wash or tumble dry. When not in use, store in a

dry, ventilated area. Never use bleach or strong solvents.

Metal Frame of Glider

Wash the metal parts with warm water and mild soap or you can use a car polish for extra

protection from dust and weather. Use WD40

, or similar product on all the nuts and

bolts.

Note: With simple care and maintenace you can prevent the metal parts from the ravages

of rust and corrosion. Store in a dry ventilated area when not in use or during harsh

weather.

SKU 90352 PAGE 5

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS

MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES

ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALI-

FIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTI-

FIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK

AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACE-

MENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS

THERETO.

Part # Description Qty

1 Ground Support Frame (Tube) 2

2 Armrest (Tube) 2

3 Vinyl Slat Supports (Back) 10

4 Vinyl Slat Supports (Seat) 10

5 Cushions 2

6 Glider Supports 4

7 Back Brace 1

8 Front Brace 1

9 Backrest Frame 1

10 Seat Frame 1

11 Seat/Backrest Support Bar 2

Part # Description Qty

A 6mm x 45mm 8

B 6mm x 50mm 4

C 6mm x 65mm 4

D 6mm x 62mm 8

PARTS LIST

HARDWARE

MAINTENANCE

For better and safer performance, keep all parts of this product clean and dry at all times.

PARTS IDENTIFICATION

SKU 90352 PAGE 6

One Stop Gardens 90352 Assembly Instructions Manual

One Stop Gardens 90352 Assembly Instructions Manual

One Stop Gardens 90352 Assembly Instructions Manual

Related papers

Other documents