BARRON TLED-XPF Series Extreme Performance Installation guide

Brand
BARRON
Model
TLED-XPF Series Extreme Performance
Type
Installation guide

BARRON TLED-XPF Series Extreme Performance is a versatile and durable lighting solution designed for various applications. It features adjustable positioning, allowing you to customize the angle of illumination based on your specific needs. The fixture auto-adjusts for voltages between 120VAC - 277VAC, making it suitable for a wide range of electrical systems. Its weather-resistant design ensures reliable operation even in challenging outdoor conditions.

BARRON TLED-XPF Series Extreme Performance is a versatile and durable lighting solution designed for various applications. It features adjustable positioning, allowing you to customize the angle of illumination based on your specific needs. The fixture auto-adjusts for voltages between 120VAC - 277VAC, making it suitable for a wide range of electrical systems. Its weather-resistant design ensures reliable operation even in challenging outdoor conditions.

TLED-XPF
INSTALLATION INSTRUCTIONS
SAVE THESE INSTRUCTIONS!
INSTALLATION INSTRUCTIONS
READ CAREFULLY AND FOLLOW ALL INSTRUCTIONS FOR YOUR OWN SAFETY
• DISCONNECT AC POWER SUPPLY BEFORE SERVICING.
• Installation and servicing of this equipment should be performed by qualified service personnel only.
• Ensure the electricity connections conform to the National Electrical Code and local regulations if applicable.
• Do not mount near gas or electrical heaters.
• Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by
unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. Any
modification or use of non-original components will void the warranty and product liability.
• Do not use this equipment for other than intended use.
800.533.3948 • www.barronltg.com
1
20070081 REV 2 - 10/16
1. Mount fixture in desired location using the supplied trunnion mounting bracket and appropriate hardware.
440
0.43
7.87
0.43
0.83
220
17.32
7.87
4.25
0.51
0.90
0.51
600
27.56
13.78 0.90
0.51
0.51
4.25
Trunnion Dimensions
Trunnion Mounting Locations
TLED-XPF
INSTALLATION INSTRUCTIONS
800.533.3948 • www.barronltg.com
2
20070081 REV 2 - 10/16
2. Feed power cord leads from fixture through the appropriate opening in trunnion.
3. Electrical connection should be made inside an approved junction box. Fixture auto adjust for voltages between
120VAC - 277VAC
a. Connect the line fixture brown lead to the black supply lead.
b. Connect the common fixture blue lead to the white supply lead.
c. Connect the ground yellow/green lead from the sevice to green grounding screw.
4. Use approved connectors to connect fixture leads to supply leads and make wire splices inside an approved
electrical box.
5. Set desired fixture angle by loosing positioning screws and rotating trunnion to desired angle. Then tighten
positioning screws.
IMPORTANT
To weather-proof your outdoor installation, be sure to seal all holes in fixture housing. (Mounting, conduit, plugs, and
photo controls, etc) with silicone sealant.
TROUBLESHOOTING CHECKLIST
TLED-XPF does not turn “ON”
1. Check incoming voltage to LED driver. Must be at least a minimum of 120VAC and no greater than 277VAC.
2. Are all the LEDs on the light engine “OFF”? If so, LED driver may be defective. Using a voltmeter, check to see if
voltage is present at the output of the power supply. If low or no voltage, then replace power supply.
3. If any individual LEDs are “OFF” the LED light engine is defective. Please have the serial number off the light engine
available when you contact technical support.
  • Page 1 1
  • Page 2 2

BARRON TLED-XPF Series Extreme Performance Installation guide

Brand
BARRON
Model
TLED-XPF Series Extreme Performance
Type
Installation guide

BARRON TLED-XPF Series Extreme Performance is a versatile and durable lighting solution designed for various applications. It features adjustable positioning, allowing you to customize the angle of illumination based on your specific needs. The fixture auto-adjusts for voltages between 120VAC - 277VAC, making it suitable for a wide range of electrical systems. Its weather-resistant design ensures reliable operation even in challenging outdoor conditions.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents