urban ambiance UQL2283 Installation guide

Brand
urban ambiance
Model
UQL2283
Type
Installation guide

urban ambiance UQL2283 is a customizable hanging light fixture with a modern and stylish design. It can be used to illuminate a variety of spaces, including living rooms, dining rooms, and bedrooms. The fixture comes with a variety of rods and chains, allowing you to adjust the hanging height to your liking. It also features adjustable shades, so you can direct the light where you need it most. The UQL2283 is easy to install and comes with all the necessary hardware. It uses standard medium-base bulbs, so you can choose the brightness and color temperature that best suits your needs.

urban ambiance UQL2283 is a customizable hanging light fixture with a modern and stylish design. It can be used to illuminate a variety of spaces, including living rooms, dining rooms, and bedrooms. The fixture comes with a variety of rods and chains, allowing you to adjust the hanging height to your liking. It also features adjustable shades, so you can direct the light where you need it most. The UQL2283 is easy to install and comes with all the necessary hardware. It uses standard medium-base bulbs, so you can choose the brightness and color temperature that best suits your needs.

Package Contents
Warnings and Cautions
1of3
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
F
B
Steel Collar
x3
6” Rod
x4
AFixture Loop
x2 EShade
x3
C12” Rod
x4
DUpper Collar
x3
G
Harp with
Socket Collar
x3
IFlat Washer
x3
JRubber Washer
x3
Diffuser
x3
L
Small Flat
Washer
x3
M
Finial
x3
STEP 1 Attach Caps to Socket
Assembly
-
A. Attach the Caps (P/Q) to the ends of the
Socket Assembly (R) and secure with the
Lock Screws (O). Hand tighten until snug.
Figure 1
Lock Screw
x2
N
Cap A
x2
O
Cap B
x2
R
Socket
Assembly
x1
Hardware Contents
AA
Crossbar
Assembly
x1
BB
Ceiling
Canopy
x1
CC
Fixture Chain
x2
DD Quick Link
x4
STEP 2 Assemble the Rods and the Fixture Loop-
A. Determine the Rods (B/C) to be assembled to the Socket Assembly
(R) according to your hanging height.
B. Pass the supply wires and ground wire through the chosen rods
(B/C) and the Fixture Loop (A). Thread the Socket Assembly (R),
the chosen Rods (B/C) and the Fixture Loop (A) together. Hand
tighten until snug.
Figure 2
R
Supply Wires
and Ground Wire
C
B
B
A
R
C
HNipple
x3
KHex Nut
x6
P
Q
Q
P
O
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (3) Medium Base 100W bulbs Maximum,Alternate bulb (3) 23W CFLMaximum.
Estimated Assembly Time: 30-45 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Installation Instructions: UQL2283
www.urbanambiance.com
2of3
STEP 3 Install Fixture Chains-
*
A. Adjust the Fixture Chain (CC) to your
desired length by removing the links if
needed.
Pliers is required for this step.
B. With the Fixture Chain (CC) not
attached to the Fixture Loop (A) and
the Canopy Chain Loop, pull the
supply wires through the Fixture Chain
(CC) alternating links. After the wires
are through the Fixture Chain (CC),
pull the Supply Wires and the Ground
Wire through the Ceiling Canopy (BB).
C. Attach one ends of the Fixture Chains
(CC) to the Fixture Loop (A) with two
Figure 8
BB
DD
CC
DD
A
Ceiling
Loop
Quick Links (DD) as shown. Lift the fixture and Fixture Chains (CC)
up and attach the other ends of the Fixture Chains (CC) onto the
Canopy Chain Loop underside of the Ceiling Canopy (BB) with the
rest two Quick Links (DD).
Suggested rods and chain length for Ceiling height :
8’ ceiling : use (1)6” rod and 2 quick links
9’ ceiling : use (1)12” rod, 5 links of chain and 2 quick links
10’ ceiling : use (2)12” rods, 5 links of chain and 2 quick links
Supply
Wires
Figure 4
STEP 4 Separate parts
from Crossbar
Assembly
-
A. Remove the Finial, the
Covers, and the Lock
Washer from the
Crossbar Assembly
(AA).
Nipple
Lock
Washer
Cover A
Cover B
Finial
AA
STEP 5 Install Crossbar-
A. AA)Attach the Crossbar (
to the Outlet Box with the
head of the Green Ground
Screw facing you. Secure
it with Outlet Box Screws
(not included) Tighten
until snug
.
.
Figure 5
Outlet
Box
Outlet
Box Screw
(not included)
Green
Ground
Screw
AA
Figure 7
STEP 7 Install Ceiling Canopy-
A. Attach the Lock Washer, the Ceiling
Canopy (BB) and the Covers over the
end of the Nipple as shown. Secure
by threading the Finial onto the
Nipple. Hand tighten until snug.
Finial
Cover B
Cover A
BB Nipple
Lock Washer
E
F
G
D
Socket
STEP 8 Install Shade-
A. Place the Upper Collar (D), the Shade (E)
and the Steel Collar (F) in turn and secure
with the Harp with Socket Collar (G). Hand
tighten until snug.
Figure 9
STEP 9 Install Bulb-
A. This fixture uses standard bulb with
medium base. Maximum 100 watts.
B. Insert bulb and screw snugly into place.
Bulb
STEP 10 Install Diffuser-
A. Thread one Hex Nut (K) to the Nipple
(H) approx half way. Screw the Nipple
(H) into the bottom end of the Harp (G)
and tighten until snug. By using pliers,
thread the Hex Nut (K) against the Harp
(G) and hand tighten until snug.
B. Thread another Hex Nut (K) onto the
end of the Nipple (H) and adjust it to
proper location for rest components.
Attach the Flat Washer (I), the Rubber
Washer (J), the Diffuser (L) and the
Small Flat Washer (M) over the Nipple
(H) in turn. Secure them with the Finial
(N) and hand tighten until snug.
Your fixture is now assembled and ready
to use. Enjoy!
G
H
Figure 10
K
K
I
J
L
MN
Figure 6
STEP 6 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
White wire
from supply Ribbed side of wire from fixture
identified with the Label “N”
Black wire from
supply (or Red)
Smooth side of wire from fixture
identified with the label “L”
Ground wire
from supply
Ground wire
from fixture
www.urbanambiance.com
2
3of3
SKU: UQL2283
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
(3) 100W
Bulbs
(Not Supplied)
Medium
Base
52.5”
23”
79”
OVERALL HEIGHT
INCLUDES 12”
CHAIN AND
(4) QUICK LINKS
9”x4.5” 1”
13.5” Dia.
60”
OVERALL HEIGHT
(4)6” AND (4)12” RODS
INCLUDES
4
5
3
1
PART NUMBER REPLACEMENT PART REQ.
NO.
1
2
UQL2283DI
UQL2283EX6
UQL2283SH
DIFFUSER
6"L ROD
METAL SHADE
3
4
3
4
3
UQL2283EX12 12”l ROD
4
5
STYLE NUMBER
UQL2283CH
CHAIN 1
www.urbanambiance.com
  • Page 1 1
  • Page 2 2
  • Page 3 3

urban ambiance UQL2283 Installation guide

Brand
urban ambiance
Model
UQL2283
Type
Installation guide

urban ambiance UQL2283 is a customizable hanging light fixture with a modern and stylish design. It can be used to illuminate a variety of spaces, including living rooms, dining rooms, and bedrooms. The fixture comes with a variety of rods and chains, allowing you to adjust the hanging height to your liking. It also features adjustable shades, so you can direct the light where you need it most. The UQL2283 is easy to install and comes with all the necessary hardware. It uses standard medium-base bulbs, so you can choose the brightness and color temperature that best suits your needs.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents