7407‐K013
SignatureCapture
KitInstructions
IssueA
Revision Record
Issue Date Remarks
A Feb2008 Firstissue
7407-K013 1
Introduction
ThiskitaddsaSignatureCapturedevicetothe7407.
25419
Signature Capture Module
Caution: StaticElectricityDischargemaypermanentlydamageyour
system.Dischargeanystaticelectricitybuildupinyourbodyby
touchingyourcomputer’scaseforafewseconds.Avoidanycontact
withinternalpartsandhandlecardsonlybytheirexternaledges.
2 7407-K013
Installation Procedure
1. TurnOffthepowertothesystemandanyconnectedperipheral
devices.Unplugthesystempowercord.
2. RemovetheColumnCover(2screws).
24895b
Column Cover
7407-K013 3
3. Usinga7/16”nutdriver,removethehexbolts(4)thatsecurethe
DisplayModuletothecountertop.
25017
4 7407-K013
4. RemovetheMountingPlatefromthecountertop(2screws).
Note: HoldtheBoltPlate(underneaththecountertop)while
removingthescrewstokeepitfromfalling.
24920
Top of Countertop
Front of Cabinet
Mounting Plate
10-32 x 2 Screws
25422
Bottom of Countertop
Front of Cabinet
Bolt Plate 10-32 x 2 Screws
7407-K013 5
5. UnpacktheSignatureCapturekit.
6. RoutetheSignatureCaptureUSBCable downthroughtheholein
thecountertop.
25420
Front of Cabinet
USB Cable
6 7407-K013
7. Insertthesupplied10‐32x2in.hexbolts(2)throughtheinner
holesintheMountingPlate,SignatureCaptureBase,and
countertop.
Note: Ifthesuppliedscrewsarenotlongenoughthenobtainnew
10‐32screwsthatmeetyourrequirements.
25423
Mounting Plate
10-32 x 2 Screws
7407-K013 7
8. PlacetheBoltPlate(removedearlierinStep#2)underthe
countertopandthreadthescrewsthroughit.SecuretheMounting
Platetothepredrilledholesinthecountertop,usingthe
appropriatetypescrewsforthetwoinnerholes.
Note: Pre‐installationcabinetandcountertoppreparationis
discussedinthe
NCR7407XpressPortHotelCheck‐InSitePreparation
Guide(B005‐0000‐1803).
25422
Bottom of Countertop
Front of Cabinet
Bolt Plate 10-32 x 2 Screws
8 7407-K013
9. RemovethefoampackingfromtheDisplayModuleandthen
installthemoduleontotheMountingPlate
25421
Display Module Column
7407-K013 9
10. Insertthesuppliedhexbolts(4)throughtheColumn,theMounting
Plate,countertop,andscrewthemintotheBoltPlate.
25424
Note: Ifthesuppliedboltsarenotthecorrectlengthforyour
particularcountertop,obtainfour¼“Hex‐headboltsofsufficient
length,aslongasneededbutnotsolongthattheymayinterfere
withthecableroutingunderneaththecountertop.
11. Tightentheboltsevenlyusinga7/16”nut
driver.
10 7407-K013
12. BundlethecablesinsidetheDisplayColumnusingthesupplied
VelcroTieoraTieWrap.
25034a
Velcro
7407-K013 11
13. InstalltheColumnCover.Slidetheuppertabintotheslotand
secureitwithscrews(2)inthebottom.
24895a
Column Cover
12 7407-K013
14. SnaptheSignatureCaptureUSBCableintotheCableGuide.
25425
USB Connector
Cable Guide
15. RoutethecoiledcablebesidetheprinterandconnectittoaUSB
portontheOutputModule.
/