Diebold Nixdorf DN Series 200C Operating instructions

Brand: Diebold Nixdorf

Model: DN Series 200C

Type: Operating instructions

DN Series™ Motorized Card Reader

Operator Manual

01750330805 A

Legal Disclaimer

This document contains proprietary information of Diebold Nixdorf, Incorporated or its subsidiaries (col-

lectively “Diebold Nixdorf“) and may include information that is protected by copyright, trademark and

patent laws in the US, Germany, and globally. All rights, including rights created by patent grants or reg-

istration of a utility model or design, are reserved.

No part of this document may be translated, reproduced, stored in a retrieval system, or transmit-

ted, in any form or by any means: electronic, mechanical, photocopying, recording, or otherwise,

without prior written permission from Diebold Nixdorf. Any violations of the foregoing may give

rise to a claim for damages.

If the document pages state the information is confidential (or words of similar import), then this

document is intended solely for the use of the employees or other personnel of Diebold Nixdorf

unless expressly authorized in writing by Diebold Nixdorf. Other uses of this information without

the express written consent of Diebold Nixdorf are prohibited.

This document should be treated as confidential material for security reasons. Any unauthorized

disclosure or use of confidential material may violate the U.S. Theft of Trade Secrets provisions

of Section 1832 of Title 18 of the United States Code as well as comparable laws in other jurisdic-

tions throughout the world, and may be punishable by fine and imprisonment.

This document and the information contained herein are provided AS IS AND WITHOUT WARRANTY.

In no event shall Diebold Nixdorf or its suppliers be liable for any special, indirect, or consequential dam-

ages of any nature resulting from the use of information in this manual. The information contained in this

document is subject to change without notice. When using the document for system implementation,

please call your authorized Diebold Nixdorf sales or service representative for any applicable changes.

Any trademarks, service marks, product names or company names not owned by Diebold Nixdorf, that

appear in this document are used for informational purposes only, and Diebold Nixdorf claims no rights

thereto, nor does such use indicate any affiliation with or any endorsement of Diebold Nixdorf or Diebold

Nixdorf products by the owners thereof.

Your use of this document and/or any of the information contained herein constitutes your agreement to

all of the terms stated on this page.

01750330805 A

Contents

1 Introduction ................................................................................................................................ 1-1

1.1 General Information ...........................................................................................................1-1

1.2 Safety Precautions .............................................................................................................1-1

1.3 General safety instructions for the component...................................................................1-2

2 Product Description................................................................................................................... 2-1

2.1 Product Features................................................................................................................2-1

2.2 Product Operation ..............................................................................................................2-2

3 Maintenance Procedures .......................................................................................................... 3-1

3.1 Beginning and Ending a Maintenance Session..................................................................3-1

3.2 Manually Retrieving Jammed Cards ..................................................................................3-1

3.3 Manually Retrieving Retained or Captured Cards..............................................................3-2

3.4 Cleaning the Card Reader .................................................................................................3-3

3.4.1 Cleaning with Commands ................................................................................... 3-3

3.4.2 Manually Cleaning with a Cleaning Card ............................................................ 3-3

3.5 Advanced Skimming Detection ..........................................................................................3-5

3.5.1 Cleaning the Lens Cover .................................................................................... 3-5

3.5.2 Fraud Verification and Removal.......................................................................... 3-6

4 Anti-Phishing Prevention .......................................................................................................... 4-1

5 Supplies ...................................................................................................................................... 5-1

Figures

Figure 2-1 Motorized Card Reader............................................................................................ 2-2

Figure 3-1 Manually Transporting Jammed Cards to the Card Slot .......................................... 3-1

Figure 3-2 Manually Transporting Jammed Cards to the Rear of the Card Reader.................. 3-2

Figure 3-3 Cleaning the Card Reader with a Cleaning Head .................................................... 3-4

Figure 3-4 Anti-skimming Device Lens Cover ........................................................................... 3-6

Figure 4-1 Anti-Phishing Module ............................................................................................... 4-1

Tables

Table 2-1 Motorized Card Reader Model Types ...................................................................... 2-1

Table 3-1 Advanced Skimming Detection Troubleshooting ..................................................... 3-5

01750330805 A

iii

1 Introduction

1.1

1.1 General Information

This document describes the features, basic operation and basic maintenance for the Diebold Nixdorf

motorized card reader.

The operator should know how to perform the following tasks before beginning other procedures in this

manual:

• Placing the system in maintenance mode.

• Returning the system to full operation.

Refer to the software documentation for information about placing the system in maintenance mode and

returning the system to full operation.

Refer to the operator manual for the system for more information about using the card reader with your

system.

1.2

1.2 Safety Precautions

Strictly observe the following safety precautions during maintenance procedures on the module. By fol-

lowing these precautions, you can reduce the risk of severe personal injury, death, or damage to the

equipment.

WARNING

Observe the following precautions when performing maintenance on the module to avoid

risk of death, severe personal injury, or damage to the equipment:

lDo not wear loose clothing or jewelry that can become caught in the equipment.

lPrevent long hair getting caught in the equipment.

lNever insert screwdrivers, pens, or other instruments into any system module or de-

vice. Severe bodily injury, death from electrical shock, or damage to equipment can

result.

lAlways completely remove AC power to the system before removing or installing

modules.

01750330805 A

1-1

Introduction

1.3

1.3 General safety instructions for the component

NOTE

Read this entire manual carefully in order to obtain a thorough knowledge with respect to

the system and the components, in addition to their operation and maintenance.

Operate the system and the components correctly in accordance with this manual in order

to avoid injuries and damage to the plant.

Keep this manual available and consult it for guidance when you are unsure about how to

carry out one or another of the procedures.

DANGER

Electrical voltage

Risk of fatal injury through contact with parts carrying electrical voltage! Switch the system

off before performing any cleaning or maintenance tasks.

lSwitch off the power switch for the power distributor.

lSwitch off the UPS, if installed.

lDisconnect the mains connection, if installed, between the UPS (Uninterruptible

Power Supply) and the system itself (see section "General power interruption" in the

operating manual).

lDisconnect the connector of the power supply cable from the electrical socket in-

stalled by the building contractor.

Repairs

DANGER

Repair work on the system or on the components may be carried out only by authorized

specialist staff. Unauthorized opening of the system or repair work carried out improperly

could result in considerable danger to the user. In case of noncompliance, excludes all lia-

bility.

01750330805 A

1-2

2 Product Description

2.1

2.1 Product Features

The motorized card reader has the following design features:

• The DN Series motorized card reader reads and writes data from and to magnetic cards, IC cards,

and smart (EMV) chip cards when the card is inserted short edge first.

• The card reader is mounted at a 5º angle on a tray that slides in and out of the system. The mounting

angle helps prevent rain dripping into the card reader.

• The card reader can be equipped with an additional card-return-on-power-failure device.

Refer to the following table for a list of the motorized card readers based on the security level.

Table2-1: Motorized Card Reader Model Types

Configuratio

Description Magnetic

Head

Encryption

Chip Card

Encryption

M1 and M2

Detection

M1 and M2

Prevention

Detection

Pre-head

Anti-

tapping

Anti-card

Trapping

(ACT)

1 HiCo Read/

Write Track

1/2/3 ICC

Basic

2 Standard

(IAFD) [1]

3 Security Pack

X X

4 Security Pack

X X X

5 Security Pack

XXXXXXX

6 ICC only Chip only and

ACT

X X

[1] The term Standard is just a name. It is not the standard motorized card reader offering, because the customer can choose

among different card reader options.

01750330805 A

2-1

Product Description

2.2

2.2 Product Operation

The following steps describe the basic operation of the motorized card reader (Figure2-1).

1. The consumer inserts the card into the slot.

2. The slot has a gate that allows the card to be partially inserted; if the card is properly oriented, the

gate opens and motorized card reader pulls the card in. If the motorized card reader is commanded

to accept chip only cards, the magnetic stripe detection is disabled.

3. The transaction begins when the card is inside the reader.

4. The card is automatically returned to the consumer at the end of the transaction.

Figure2-1: Motorized Card Reader

1Card-return-on-power-failure device (capacitor or back up battery)

2Mounting plate

3Card retain bin

4Motorized card reader

5Inner bezel

6Customer card inserted short edge first

01750330805 A

2-2

3 Maintenance Procedures

3.1

3.1 Beginning and Ending a Maintenance Session

The operator should know how to perform the following tasks before using the other procedures in this

section.

• Opening the system to access the card reader.

• Placing the system in the maintenance mode.

• Returning the system to full operation.

Refer to the operator manual for the system for more information about these tasks.

3.2

3.2 Manually Retrieving Jammed Cards

The consumer's card can sometimes get stuck in the transport mechanism. Use the following steps to

manually remove jammed cards.

1. Place the system in the maintenance mode.

2. To eject a jammed card toward the card reader entry slot, push and hold the plunger of the shut-

ter solenoid to open the shutter. Refer to the following figure.

3. Rotate the drive train pulley away from the card slot (counterclockwise) until the card can be re-

trieved at the card slot.

Figure3-1: Manually Transporting Jammed Cards to the Card Slot

1Shutter solenoid plunger

2Card slot

3Turn the drive train pulley counterclockwise

4. Make sure that you do not force cards out the front of the system where an unauthorized person

might retrieve them.

01750330805 A

3-1

Maintenance Procedures

5. If you cannot free the customer card, contact your customer service representative.

6. To eject a jammed card toward the rear of the card reader, rotate the drive train pulley clockwise

until the card can be retrieved at the rear of the card reader. Refer to the following figure.

Figure3-2: Manually Transporting Jammed Cards to the Rear of the Card Reader

1Rear of card reader

2Turn the drive train pulley clockwise

3.3

3.3 Manually Retrieving Retained or Captured Cards

The motorized card reader has an open retained card bin or a locked retained card bin to store cap-

tured cards. The retained card bin holds all cards not returned to consumers.

A card may be retained for the following reasons:

• The network commanded the system to retain the card.

• The consumer left the card in the card slot loo long after the transaction session ended.

• After a power failure process ended.

Perform the following steps to manually retrieve retained or captured cards.

1. Open the system and gain access to the card reader.

2. Remove the captured cards from the card bin.

01750330805 A

3-2

Maintenance Procedures

3.4

3.4 Cleaning the Card Reader

3.4.1

3.4.1 Cleaning with Commands

Use the T/SOP interface to clean the card reader with a cleaning card. The Technical Service and Oper-

ating (T/SOP) for ProBase/C and ProBase/J User Manual describes how to run a cleaning card through

the card reader. Use a cleaning card to clean the card reader regularly, every six months under normal

conditions.

WARNING

The cleaning card can jam if the thickness of the card varies from the standard size or if a

non-rigid cleaning card is used. Check the card before beginning the cleaning process.

Perform the following steps to clean the card reader with commands.

1. Place the system in maintenance mode.

2. Insert the head cleaning card into the card slot.

3. The card reader tries to read the cleaning card, moves the card over the read head that is being

cleaned and finally ejects the card. It may be necessary to repeat the operation several times.

4. Return the system to the normal mode of operation.

5. Dispose of cleaning card.

3.4.2

3.4.2 Manually Cleaning with a Cleaning Card

Use a cleaning card to clean the card reader regularly, every six months under normal conditions.

CAUTION

Using anything other than the recommended cleaning cards can damage the card reader.

Perform the following steps to manually clean the card reader with a cleaning card.

1. Push and hold the plunger of the shutter solenoid to open the shutter. Refer to Figure3-3.

2. Insert the cleaning card short edge first into the card slot.

3. Move the cleaning card toward the rear of the card reader by rotating the drive train pulley clock-

wise until the cleaning card can be retrieved at the rear of the card reader.

4. Repeat Step 2 and Step 3 if more cleaning is needed.

5. Retrieve the cleaning card.

6. Dispose of the cleaning card.

01750330805 A

3-3

Maintenance Procedures

Figure3-3: Cleaning the Card Reader with a Cleaning Head

1Rear of card reader 3Insert cleaning card

2Solenoid plunger 4Turn the drive train pulley clockwise

01750330805 A

3-4

Maintenance Procedures

3.5

3.5 Advanced Skimming Detection

Advanced Skimming Detection has the following features:

• Advanced Skimming Detection is an anti-skimming sensor installed on the card reader. The sensor

detects the presence of a customer presenting a card to the card reader or the presence of a foreign

object attached to the card reader bezel area. This sensor identifies card reader fraud devices.

• Use T/SOP to identify the problem. Refer to the following information to resolve the problem.

Table3-1: Advanced Skimming Detection Troubleshooting

Status/Problem Probable Cause Corrective Action Refer to...

Advanced skimming de-

tection is disabled

Not configured Enable anti-skimming

option in FDD (foreign

device detection) config-

uration screen. Contact

your Service Represen-

tative to activate the fea-

ture.

Failure Anti-skimming sensor is

damaged

Contact your Service

Representative to re-

place the card reader.

Fraud Skimmer device is in-

stalled

1. Remove the skimmer

device.

2. Click the LatchReset

button and check the

Foreign Device Detec-

tion Status of the card

reader again.

Section3.5.2

Anti-skimming sensor is

dirty

Clean the card reader

lead-through indicator

cover.

Section3.5.1

Anti-skimming sensor is

damaged

Contact your Service

Representative to re-

place the card reader.

3.5.1

3.5.1 Cleaning the Lens Cover

Refer to the following information when cleaning the lens cover:

• Clean the lens when the anti-skimming device (ASD) sensor is dirty.

• Use a cloth and ethyl alcohol to clean the cover of the lens.

• A solution of simple green found in the Diebold Nixdorf cleaning kit may also be used.

01750330805 A

3-5

Maintenance Procedures

Figure3-4: Anti-skimming Device Lens Cover

1Anti-skimming device lens cover

3.5.2

3.5.2 Fraud Verification and Removal

Fraud Verification

• The UXL (user experience light) can be seen if there is NO fraud device on the card reader.

• If you cannot see the UXL (user experience light), there might be a fraud device on the card reader.

• Remove the fraud device and allow the appropriate Security procedures to report locating a device

on the system.

FDD (Foreign Device Detection) Latch Configuration

To verify the ON/OFF status of the latch, go to the FDD (Foreign Device Detection) device configuration

screen on the diagnostic tool.

FDD LatchReset button

Perform the following steps to clear the Foreign Device Detection status of the reader.

1. Go to the FDD Status & Test screen on the diagnostic tool.

2. Click the LatchReset button.

M3 Anti-skimming

• The motorized card reader can detect M3 skimmers placed inside the motorized card reader.

• M3 prevention is achieved by minimizing the void space at the transport area as much as possible.

01750330805 A

3-6

4 Anti-Phishing Prevention

The anti-phishing (sometimes called anti-fishing) prevention module has the following design features:

• Designed for any motorized card reader with anti-phishing previously installed.

• When the anti-phishing module is moved, it restrains an ATM card so that it cannot be ejected from

the card reader.

To unlock the operation of the anti-phishing module, check the status of the anti-card trapping (ACT) in

T/SOP. If it is activated, release it before trying to manually move the card.

To manually move the card, turn the knob in the direction of the arrows on the knob to unlock the anti-

phishing module. Perform the following steps.

• Do not turn the knob in the reverse direction after it is locked. If you do, the locking mechanism will

be stuck in the guide frame and become immovable.

• Do not try to move the card back and forth when the locking mechanism is engaged on the card, be-

cause it may become unable to release.

• Do not continuously send lock release command. If you do, the stepping motor will become hot and

there is a risk of burn injury.

Figure4-1: Anti-Phishing Module

1Turn knob in the direction of arrows on the knob

2Anti-phishing module

01750330805 A

4-1

5 Supplies

For best performance, you should only use supplies purchased from Diebold Nixdorf. Supplies and ac-

cessories are fully guaranteed. Shop for media and consumables through customer support at Diebold-

Nixdorf.com. Use the following supplies to service the motorized card reader.

Supplies Part Number

Head cleaning card, motorized card reader 01750340744

01750330805 A

5-1

DIEBOLD NIXDORF

5995 Mayfair Road | North Canton, OH 44720 | United States

Diebold Nixdorf DN Series 200C Operating instructions

Diebold Nixdorf DN Series 200C Operating instructions

Diebold Nixdorf DN Series 200C Operating instructions

Related papers

Other documents