2. Avaya
  3. Business Communications Manager - Programmable Analog Interface
Business Communications Manager - Programmable Analog Interface

Avaya Business Communications Manager - Programmable Analog Interface User manual

  • Hello! I am an AI chatbot trained to assist you with the Avaya Business Communications Manager - Programmable Analog Interface User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Information Sheet
Business Communications
Manager Programmable Analog
Interface
All Business Communications Manager software has built-in market profiles. Some market
profiles include analog parameters. You can customize the specified market profile analog
parameters using a customizable Analog profile in addition to the Market profile.
A customized analog profile does not replace a market profile. Analog profiles provide
additional customization to an existing market profile, and only work with the market profile
with which is was developed.
Customization of analog profiles applies to
• BCM50 3.0:
— Analog Trunk interface: GATI and GATM
— Analog Stations interface: GASI and GASM
• BCM450 1.0:
— Analog Trunk interface: GATM
— Analog Stations interface: GASM
Customizing and localizing an analog profile is a process that you complete with the
assistance of a licensed Nortel technician:
1 Contact the local Nortel sales office to request market profile customization for your
market.
2 The Nortel prime identifies a licensed Nortel technician, who uses a proprietary BCM data
entry tool to customize the analog parameters of the market profile for you.
3 The technician creates a .amp analog profile file and loads it onto your BCM system to
test.
4 The Analog Profile is distributed through a permanent software update patch that you can
apply to any BCM50 3.0 or BCM450 1.0 that requires the modified analog parameters.
You can activate an analog profile on a BCM50 3.0 system using the Business Element
Manager.
.
2
NN40010-677
Activating an analog profile through the BCM50 3.0 Business
Element Manager
On a BCM50 3.0, you can activate a customized analog profile through the Business Element
Manager. After you have worked with an authorized Nortel technician to create and install your
customized analog profile, complete the following procedure to activate the profile.
1 In the Business Element Manager, navigate to Configuration > System > Telephony
Regions.
The Analog Profiles panel appears.
2 From the Profiles are, click on the analog profile you want to activate.
3 In the Regions column of the Profiles table, ensure that the correct region is selected.
4 Click Activate.
A message indicates that you must reset the core telephony with the region of the active profile
to enable settings.
5 Click OK.
6 Click the Reset Telephony button to fully activate the profile.
The system undergoes a cold reset and the profile is activated.
Or
In the Business Element Manager, navigate to Administration> Utilities > Reboot.
Click Reboot.
The system undergoes a warm reset and the profile is activated.
Removing a profile file from a BCM50 3.0 or a BCM450 1.0
The set-based administration interface to the analog profile status can be used to access the profile
file status and to optionally remove the profile. Administration telset interfaces are accessible only
by a user with an Installer level of telset user privileges. Use the set-based administration interface
to access the programmable analog interface status, and optionally remove the current analog
profile file if it is determined that the installed analog profile file is inappropriate for your
installation.
3
Business Communications Manager Programmable Analog Interface
The profile should only be removed under guidance from Nortel Support (1-800-nortel support).
Alarms
If your system does not have an analog profile, no new alarms appear on your system. If your
system has an analog profile, the following new alarms can appear.
1.Call 1-800-nortel support to reach an authorized Nortel technician.
2.In the handset interface, press ** Option.
3.Log on by following the voice prompts or the display button options.
4.Enter your password and press OK.
5.Press Next to continue through the screens until you reach the
Profile File screen.
The Profile File screen appears. The Profile status is Y if a profile file
exists.
If the Profile status is N, then no profile file exists on the BCM system
and no further action is required.
6.Press DEL.
The file is removed, and the Profile File status changes to N.
7.To remove the parameters from the interface, perform a warm
restart of the BCM system.
Refer to the Telset Administration Guide for your BCM platform for the
procedure to perform a warm restart.
Table 1 Programmable analog interface alarms
Alarm
number Alarm text Action
382 Market profile does not match
analog profile base market
profile
The market profile you selected in the BCM does not
match the market profile used as a base for the
analog profile file. Either change the BCM market
profile, or change (or delete) the profile file.
383 Profile is corrupt or invalid. You cannot use the profile file you selected. Delete or
replace the profile file.
User ID:_
CANCL BKSP OK
Password:_
CANCL BKSP OK
Profile File: Y
DEL
Profile File: N
DEL
4
NN40010-677
www.nortel.com
Copyright 2009
Sourced in Canada
Document number: NN40010-677 01.02
Standard
July 2009
/