Danfoss SpeedUp - Direct load User guide

Brand: Danfoss

Model: SpeedUp - Direct load

Type: User guide

Danfoss SpeedUp - Direct Load

With Danfoss SpeedUp - Direct load, you have purchased a high-quality heating system that is suitable for residential and commercial use. It consists of massive wooden planks on battens and is designed for direct load. The system is easy to install and can be used in a variety of applications, including:

Residential spaces, hallways, and attic spaces in residential buildings and hotel rooms
Office spaces, hallways in office buildings, medical offices, stations, and spaces with human occupancy
Commercial spaces with floor areas up to 50 m² in residential or office buildings

Danfoss SpeedUp - Direct Load

Residential spaces, hallways, and attic spaces in residential buildings and hotel rooms
Office spaces, hallways in office buildings, medical offices, stations, and spaces with human occupancy
Commercial spaces with floor areas up to 50 m² in residential or office buildings

Application sheet

SpeedUp

Massive wooden planks on battens

Direct load

1 Wooden planks ≤ 22 mm

2 SpeedUp heat panel + FH composite pipe 30 mm

3 Support batten (30mm)

4 Additional insulation EPS 035 DEO 20 mm

5 SpeedUp perimeter insulation

6 If necessary moisture barrier

Floor nish ≤ 22 mm Massive wooden planks or parquet

Construction height ≤ 72 mm Height including oor nish

Weight ~ 19 kg / m² Weight including oor nish

Thermal resistance R 1,43 m²K / W The minimum thermal resistance requirement of DIN EN 1264 is

fullled.

Thermal transmission coecient U 0,63 W / m²K If the architectural design species better thermal insulation, this

must be taken into account.

Design load ≤ 2,0 kN / m²

Point load (≥ 20 cm²) ≤ 2,0 kN Sum point load ≤ design load; please notice special heavy ob-

jects (aquaria etc.)

Impact subsonic noise reduction NA dB

Application area

Residential spaces, hallways and attic spaces in residential buildings and hotel rooms.

Corresponds to categories A1, A2 and A3 of DIN 1055-3. Oce spaces, hallways in oce

buildings, medical oces, stations and spaces with human occupancy, and commercial

spaces with oor areas up to 50 m² in residential or oce buildings. Corresponds to

categories B1, D1 and D2 of DIN 1055-3.

Requirements & special features

A level, smooth and structurally sound surface is necessary for full surface contact with

the heating elements (elevated requirements according to DIN 18202 Table 3, row 4).

Structural sealing according to DIN 18195 must be placed beneath the oor panel in case

of structures facing the ground, and otherwise on the unnished oor. The R value must

be increased if the groundwater level is less than or equal to 5 m. A U value not exceed-

ing 0.5 W/m²K must be maintained in existing buildings and additions with areas up

to 50 m². If necessary, protect oorboards and prefabricated parquet against moisture

penetration from below according to the manufacturer’s instructions (vapour barrier).

Observe all installation instructions and manufacturer’s instructions.

Additional insulation

20 mm EPS 035 DEO 200 kPa; existing buildings: 40 mm XPS 035 500 kPa

Construction

According to EnEV, EN 1264, DIN 1055, 18195 and 18202

Construction number 82

Technical Data Floors/ceilings facing unheated rooms or the ground

VA.CR.Q1.02

Danfoss HES

Danfoss SpeedUp - Direct load User guide

Brand: Danfoss

Model: SpeedUp - Direct load

Type: User guide

Danfoss SpeedUp - Direct Load

Residential spaces, hallways, and attic spaces in residential buildings and hotel rooms
Office spaces, hallways in office buildings, medical offices, stations, and spaces with human occupancy
Commercial spaces with floor areas up to 50 m² in residential or office buildings

Download PDF

report

Danfoss SpeedUp - Direct load User guide

Danfoss SpeedUp - Direct load User guide

Related papers