Remove quick connect from the end of spray
hose. Place new faucet through holes in top
of sink.From underside, assemble S.S
washer (1) and mounting nut (2) onto shank
and tighten mounting nut . Firmly tighten the
locking screws (3) to S.S washer. Do not
overtighten .
Connect sprayer hose
Screw quick connector to the free end of
spray hose.
Align block and tabs on quick connect. Push
quick connect housing firmly upward and
snap onto receiving block. Pull down
moderately to ensure connection has been
made. If it is necessary to remove quick
connect, squeeze tabs on hose between
index finger and thumb, then pull down to
disconnect. Locate the weights (1) twenty
inch (20") from the underside of the sink
deck .
Making the waterline connections:
Use 1/2 in. I.P.S. faucet connections (2, not
included), or use the coupling nuts (3, not
included) with a 3/8 in. O.D. ball-nose riser
(1, not included). Use wrenches when
tightening. Do not overtighten.
NOTE: The hot side inlet tube is indcated
by a label. If the label is not present, the hot
supply tube is the longer of the two inlet
tubes.
Faucet Operation and Inspection
Turn on hot and cold water supplies. Pull the
hose assembly
out of the spout and remove the spray
head.Be sure to hold the end of the hose
down into the sink and turn faucet handle to
the mixed position.Flush water lines for
one minute. Check for leaks. Re-tighten if
necessary, but do not overtighten. Reinstall
the spray head tight.
5.
3.
6.
4.
Cleaning:
To maintain and protect the fine luster of all products, clean with a soft, damp cloth
only. DO NOT USE detergents or cleansers as they may harm the protective finish.
Model Number: 120439LF & 120440LF & 125467
INSTALLATION
INSTALLATION STEPS: Single handle kitchen faucet
1
3
2
1
3 2
2
3
1
20''
1
Shut off water supply at angle stop. Remove
old faucet. Clean sink surface in preparation
for new faucet.
1.
2.
Install cover plate (optional)
Remove old faucet, Clean sink surface.
Place base plate (2) and cover plate (1) on
the sink . If you do not use cover plate,
please use flange (3) to replace cover plate
and base plate.
Brand Lavatory Faucets
Tools:
Adjustable wrench
Groove joint pliers
Pipe wrench
Screwdriver
Thread sealant tape
Basin wrench
Plumber's putty
QTY.PART NO.NO. PART DESCRIPTION QTY.PART NO.NO. PART DESCRIPTION QTY.PART NO.NO. PART DESCRIPTION
11
Mounting Kit
11
1
994670 994670
Mounting Kit
1
10
1
2
4
5
6
3
8
9
7
1
994658
5
Ceramic Cartridge
1
189
8
Quick Connect
9
6
Pull Out Sprayer
Spray Hose
7
1
1
994728
188
2
4
Bonnet Nut
Bonnet Cap
3
1
1
994714
994712
1
Handle Assembly
1994723
1
994658
Ceramic Cartridge
1
994658
5
Ceramic Cartridge
1
189
Quick Connect
8
Lower Escutcheon Kit
10
1
994732
9
Pull Out Sprayer
Spray Hose
1
1
994729
188
6
7
1
189
Quick Connect
994726Lower Escutcheon Kit
1
994696
188
Pull Out Sprayer
Spray Hose
1
1
2
Bonnet Nut
Bonnet Cap
1
1
994714
994713
4
3
Handle Assembly
1994724 1
994714
994694
Bonnet Nut
Bonnet Cap
1
1
994725
Handle Assembly
1
MODEL NO.120439LF MODEL NO.120440LF MODEL NO.125467
120439LF & 120440LF & 125467
1
3 Hole Deck Plate Kit
Hose Weight
190
994573
1
1
3 Hole Deck Plate Kit
Hose Weight
994573
994727
1
1
12
12
3 Hole Deck Plate Kit
Lower Escutcheon Kit
12
Hose Weight
11
Mounting Kit
10
1
1
994573
994717
1
1
994670
994730
8
9
10
4
3
2
1
6
7
5
11
12
13
13
Block
O-ring
129
130
1
1
13
Block
O-ring
129
130
1
1
13
Block
O-ring
129
130
1
1
www.premierfaucet.com, [email protected]
/
