Premier 110703 Installation guide

Premier
Brand
Premier
Model
110703
Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

Premier 110703 is a single handle bar faucet, designed for easy installation and maintenance. It features a durable construction with a fine luster that can be maintained with a soft, damp cloth. The faucet includes a 3-hole deck plate kit for flexible installation options, and its waterline connections are compatible with 1/2 in. I.P.S. faucet connections or 3/8 in. O.D. ball-nose risers. The hot side inlet tube is clearly labeled for easy identification during installation.

Premier 110703 is a single handle bar faucet, designed for easy installation and maintenance. It features a durable construction with a fine luster that can be maintained with a soft, damp cloth. The faucet includes a 3-hole deck plate kit for flexible installation options, and its waterline connections are compatible with 1/2 in. I.P.S. faucet connections or 3/8 in. O.D. ball-nose risers. The hot side inlet tube is clearly labeled for easy identification during installation.

INSTALLATION STEPS: Single handle bar faucet
Cleaning:
To maintain and protect the fine luster of all products, clean with a soft, damp cloth
only. DO NOT USE detergents or cleansers as they may harm the protective finish.
INSTALLATION
Model Number: 120347LF & 120348LF & 110703
Place new faucet hoses and thread rod
through the center hole of sink.
3.
Shut off water supply at angle stop. Remove
old faucet. Clean sink surface in preparation
for new faucet.
1.
Install cover plate (optional).
Place base plate (2) and cover plate (1) on
the sink. If you do not use the cover plate,
please use flange (3) and seat (4) to replace
cover plate and base plate.
2.
From underside, assemble rubber washer,
metal washer, and mounting nut onto the
thread rod and tighten mounting nut. Do
not overtighten.
4.
Making the waterline connections:
Use 1/2 in. I.P.S. faucet connections (2, not
included), or use the coupling nuts (3, not
included) with a 3/8 in. O.D. ball-nose riser
(1, not included). Use wrenches when
tightening. Do not overtighten.
NOTE: The hot side inlet tube is indcated by
a label. If the label is not present, the hot
supply tube is the longer of the two inlet
tubes.
5.
3
1
2
Important: After installation is completed,
remove aerator. Turn on water supply and
allow both hot and cold water to run for at
least one minute each. While water is
running, check for leaks. Replace aerator.
6.
3
4
1
2
Brand Lavatory Faucets
Tools:
Adjustable wrench
Groove joint pliers
Pipe wrench
Screwdriver
Thread sealant tape
Basin wrench
Plumber's putty
1
2
8
7
5
4
6
3
9
12
10
11
120347LF & 120348LF & 110703
994721Bonnet Nut
1
5
Mounting Kit
3 Hole Deck Plate Kit
Lower Escutcheon Kit
Handle Screw & Index Plug
Handle Assembly
Bonnet Cap
10
Aerator
11
12
9
8
7
6
1
338
1
339
165
1
1
336
337
1
335
334
1
1
Accessorize Head
Ceramic Cartridge
PART DESCRIPTION
NO.
Washer
2
O-Rings
4
3
1
QTY.PART NO.
44 1
994658
45 1
1
331 1
MODEL NO.110703MODEL NO.120347LF
PART DESCRIPTION
Lower Escutcheon Kit
3 Hole Deck Plate Kit
Handle Screw & Index Plug
3
O-Rings
11
Mounting Kit
12
Aerator
9
10
6
Bonnet Cap
7
8
Handle Assembly
4
5
Bonnet Nut
Ceramic Cartridge
2
1
Washer
Accessorize Head
NO.
45 1
1
165
1
994681
1
1
116
113
1
104
1
1
110
164
994658
994721
1
1
44
43 1
1
QTY.PART NO.
145 3
O-Rings
Handle Screw & Index Plug
Lower Escutcheon Kit
3 Hole Deck Plate Kit
11
Mounting Kit
12
Aerator
9
10
1
165
994682
1
1
114
117
1
Ceramic Cartridge
6
Bonnet Cap
7
8
Handle Assembly
4
5
Bonnet Nut
1
105
1
166
111
1
1
994658
1
994721
MODEL NO.120348LF
PART DESCRIPTION
Accessorize Head
1
2
Washer
NO.
150
144
QTY.PART NO.
www.premierfaucet.com, [email protected]
  • Page 1 1
  • Page 2 2

Premier 110703 Installation guide

Premier
Brand
Premier
Model
110703
Category
Sanitary ware
Type
Installation guide
This manual is also suitable for

Premier 110703 is a single handle bar faucet, designed for easy installation and maintenance. It features a durable construction with a fine luster that can be maintained with a soft, damp cloth. The faucet includes a 3-hole deck plate kit for flexible installation options, and its waterline connections are compatible with 1/2 in. I.P.S. faucet connections or 3/8 in. O.D. ball-nose risers. The hot side inlet tube is clearly labeled for easy identification during installation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents