6.
3.
2.
4.
1.
INSTALLATION STEPS: Single handle kitchen faucet
Cleaning:
To maintain and protect the fine luster of all products, clean with a soft, damp cloth
only. DO NOT USE detergents or cleansers as they may harm the protective finish.
INSTALLATION
7.
5.
Model Number: 120076 & 120077
Important: After installation is completed. Turn
on water supply without the sprayer to run for
at least one minute each. Check for leaks.
Re-tighten any connections if necessary, but
do not overtighten. Reinstall sprayer head by
hand tightening it back onto the spray hose.
Shut off water supplies.
Before installation, remove quick connector
from the free end of pullout hose.
If installing the faucet with the escutcheon,
begin with step 2. If installing the faucet with
flange, begin with step 3.
Retract pull-out hose (1) up through faucet
body, until the pull-out hose fitting is flush
with the bottom of shank (2). Do not pull
hose fitting past the shank. Insert faucet
body through the hole in escutcheon.
Note: Do not feed the pull-out hose (1)
back down through the spout until step 4.
Retract pull-out hose (1) up through faucet
body, until the pull-out hose fitting is flush
with the bottom of shank (2). Do not pull
hose fitting past the shank. Insert faucet
body through the hole in escutcheon.
Note: Do not feed the pull-out hose (1) back
down through the spout until step 4.
To Install Soap Dispenser
Remove the bottle. Separate head from
body assembly. Make sure flange is
properly seated in the base of the body
assembly. Insert body assembly through
selected hole in sink. Secure body
assembly to sink with nut. From under the
sink screw the bottle onto the body
assembly shank, then attach head
assembly.
Making the waterline connections:
Use 1/2 in. I.P.S. faucet connections (2, not
included), or use the coupling nuts (3, not
included) with a 3/8 in. O.D. ball-nose riser (1,
not included). Use wrenches when tightening.
Do not overtighten.
NOTE: The hot side inlet tube is indcated by a
label.
Screw quick connector to the free end of
pull-out hose. Align block (1) and tabs (2)
on quick connector. Push quick connector
housing firmly upward and snap onto
receiving block. Pull down moderately to
ensure connection has been made.
After connecting the hose, attach weights
(3) to hose at bottom of loop to prevent
hose from twisting and return hose to
proper position.
2
1
3
2
1
3
1
2
1
2
Brand Lavatory Faucets Tools:
Adjustable wrench
Groove joint pliers
Pipe wrench
Screwdriver
Thread sealant tape
Basin wrench
Plumber's putty
120076 & 120077
19
8
Ring 250 1
15
130 1
16 Weights
10
Sprayer
Inverter
Flange & Washer
12
14 Washer & Nut
13
11
Escutcheon&Base Plate
251
252
30
1
1
1
253
994573
129
1
1
1
321 1
PART DESCRIPTION
NO.QTY.PART NO.
O-ring
Cap
1
3
2 Handle
Set Screw
5
7
6 Bonnet
Cartridge
4
247
20
248 1
1
1
18
994658
249 1
1
1
16 1
MODEL NO.120076
1
2
3
5
6
8
9
10
9
11
12
13
14
15
16
17
18
Handle Seat
9
17
18 Dispenser Soap
O-ring
Block
1
254
1
250
8
Ring
1
253
13
Washer & Nut
16
O-ring
17
Dispenser Soap
14
Weights
15
Block 1
130 1
258
1
994573 1
129
Escutcheon&Base Plate
Flange & Washer
Inverter
9
10
Sprayer 1
31 1
320
1
251 1
257
1
256
3 Handle Seat
6
Cartridge
O-ring
7
Cap
4
5 Bonnet
1
994658 1
249
1
17 1
18
PART DESCRIPTION
MODEL NO.120077
NO.
1 Handle
2 Set Screw
PART NO. QTY.
1
255
1
20
11
12
18
O-ring 259 1 O-ring 259 1
4
7
Screw 307 1 Screw 307 1
19 19
www.premierfaucet.com, [email protected]
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Design House 522847 Installation guide
-
Glacier Bay 65710N-B8427H2 Installation guide
-
-
KRAUS KPF-1690-FF-100BG User manual
-
-
-
Cahaba CA6112SS User manual
-
Cahaba CASC0068 Operating instructions
-
-
