2. Shading Systems
  3. Side Channel/Sill Angle
Side Channel/Sill Angle

Shading Systems Side Channel/Sill Angle, 9900837, GEN3, Qadvanced, QBasic+, Qfree, QIS, QLINK Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Shading Systems Side Channel/Sill Angle Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Page 1 of 2 PN 9000140 Revision 5.31.14
Tools Required
Measuring Tape
Pencil with eraser
Level
Ladder
Flat Head Screw Driver
#2 Phillips Screw Driver
Power Drill with:
3/32” Drill Bit
#2 Phillips Drive Bit
IMPORTANT
Read and understand all instructions before installing.
Always wear personal protection equipment including
safety glasses and gloves. Use a ladder per its
manufacturer’s instructions. Work safely!
TILT OUT SIDE CHANNELS
INSTALLATION INSTRUCTIONS
PARTS
Ensure that all parts are present.
Tilt Out
Side Channel Assembly
Warning:
When subject to air pressure differentials shade vertical edges may
become disengaged from side channels resulting in a condition that will
damage the fabric if the shade is opened. Do not leave
windows open and shades closed especially when opening and closing
doors to the room the shade(s) are installed in. Do not subject shade to air
pressure differentials when installed in conjunction with side channels.
TYPICAL
Part Quantity
Side Channel Assembly 2
Sill Angle 1
Mounting Screws 1 per foot
SILL ANGLE (Optional)
The Sill Angle can be configured in two ways, with the vertical side behind the hembar. It should
always be installed such that it does not prevent the Side Channels from tilting open. Before
installing, cut a notch in the corner of the Sill Angle so it butts up to the Side Channel. It is not
recommended to slide the Sill Angle under the Side Channels. It restricts tilting open, during
battery change, and it moves the Side Channels up negating the 1/8” gap between the bracket
and top of the Side Channels.
.250
.375
.250
1.250
.250
.375
.250
1.250
.375
1.250
Page 2 of 2 PN tbd Revision 5.31.14
INSIDE MOUNT INSTALLATION
STEP 1
After installing the shade, but before programming it, move
the shade down at least 12” from the Open position by
pulling the hem bar. If the fascia is installed, remove it.
STEP 2
Tilt the fabric out of the window opening. Slide the Side
Channel assembly onto the fabric as shown. Make sure
thinner side or front part of side channel faces room.
IMPORTANT
Always install the Side Channels with the hinge at the top and closed.
Shade Fabric
Side Channel Hembar
STEP 3
Insert the assembly into the window opening.
Side Channel
STEP 4
Repeat for the other side.
STEP 5
Place the optional Sill Angle into window opening in the
desired orientation. You may need to move or hinge open
each Side Channel, depending on Sill Angle configuration.
STEP 6
Pull the shade down to the
50% position and adjust the Side
Channels so that the shade fabric Fabric
hangs straight down into them.
Side
Channel
STEP 7
Holding the Side Channel plumb, drive screws into the
pre-drilled holes.
Important: Only drive screws into pre-drilled holes so they do not
interfere with fabric or hem bar. Failure to do so could lead to damage
or malfunction.
OUTSIDE MOUNT INSTALLATION
IMPORTANT
Side Channels do not come with pre-drilled holes for outside mounts.
When drilling holes in back of Channel, start at least 12” from top to
ensure drill clearance.
STEP 1
Pre-drill holes in the back of each side channel every 12”
or as needed.
STEP 2
After installing the shade, but before programming it, move
the shade down at least 12” from the Open position by
pulling the hem bar. If the fascia is installed, remove it.
STEP 3
Slide the Side Channel assembly onto the fabric as
shown. Make sure thinner side or front part of side
channel faces room. Repeat for the other side.
IMPORTANT
Always install the Side Channels with the hinge at the top and closed.
Shade Fabric
Side Channel
STEP 3
Mount the assembly onto desired part of wall.
Side Channel
STEP 4
With the Side Channel up, drive screw in top hole. Line up
Side Channel straight and finish driving additional screws
in the pre-drilled holes.
QADVANCED WITH SIDE CHANNELS
INSTALLATION INSTRUCTIONS
Note: Leave 1/8”
space between
bottom of bracket and
top of side channels.
Note: Leave 1/8”
space between
bottom of bracket and
top of side channels.
/