Legrand Teleshade With QIS Drive Cassette System User guide

Brand: Legrand

Model: Teleshade With QIS Drive Cassette System

Type: User guide

Solarfective

QIS Hardwired Roller Shade

Installation Instructions

No: SF-QISInst – 08/18 rev. 1

Catalog Numbers • Les Numéros de Catalogue • Los Números de Catálogo: QIS

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

MOTOR SIDE

BRACKET

(Spindle Key-hole)

ROLLER SHADE

SPRING SIDE

BRACKET

(Spindle Clip)

END CAP

FASCIA

POWER & COMMUNICATION PANEL POWER BRICK & CORD

(FOR POWER & COMMUNICATION PANEL)

MOUNTING SCREWS

WALL SWITCH

SINGLE AND DUAL CHANNEL

(OPTIONAL)

Package Contents:

• Hardwired Roller Shade

• Motor Side Bracket

• Spring Side Bracket

• End Cap x 2

• Fascia (Optional)

• Mounting Screws

• Power & Communication Panel

• Power Brick & Cord

• Wall Switch (Optional)

Recommended Tools:

• Cable Management / Cable Tie Downs

• Measuring Tape

• Power Drill with 3/32” Bit & 1/4” Nut Driver

• Flat Head Screwdriver

• #2 Phillips Head Screwdriver

• Level

• Pencil

• Ladder

CONTENTS

Fascia Brackets ................................................................................................................................................................................... 3

Universal Brackets .............................................................................................................................................................................. 3

Outside Mount ..................................................................................................................................................................................... 3

Fascia Bracket Hardstop Removal ......................................................................................................................................................... 4

Fascia Bracket Installation ...................................................................................................................................................................... 4

Inside Mount – Standard Roll .............................................................................................................................................................. 4

Inside Mount – Reverse Roll ............................................................................................................................................................... 5

Outside Mount – Standard Roll ........................................................................................................................................................... 6

Outside Mount – Reverse Roll ............................................................................................................................................................ 7

QIS Cable Placement ............................................................................................................................................................................... 7

Shade Installation ..................................................................................................................................................................................... 8

Fascia Installation .................................................................................................................................................................................... 9

Standard Fascia .................................................................................................................................................................................. 9

Reverse Fascia ................................................................................................................................................................................... 9

Universal Bracket Installation ............................................................................................................................................................... 10

Inside Mount – Standard Roll ............................................................................................................................................................ 10

Inside Mount – Reverse Roll ............................................................................................................................................................. 11

Outside Mount - Standard Roll .......................................................................................................................................................... 12

Outside Mount - Reverse Roll ........................................................................................................................................................... 12

Fascia End Cap Installation ................................................................................................................................................................... 13

Universal End Cap Installation .............................................................................................................................................................. 13

QIS Power & Communication Panel Setup .......................................................................................................................................... 14

Wire Specification: ............................................................................................................................................................................ 14

Maximum length of wire from Power & Communication Panel to device:......................................................................................... 14

Maximum length or wire for Hardwired 4 and 8 Button Switches: .................................................................................................... 14

Maximum wire length for RS485 communication: ............................................................................................................................. 14

System Capacity: .............................................................................................................................................................................. 14

Power & Communication Panel: ....................................................................................................................................................... 14

Power & Communication Panels and Third Party Integration via RS485 ......................................................................................... 14

Wiring for Cat 5e/6 Cable .................................................................................................................................................................. 14

QIS Wall Switch Programming Instructions ........................................................................................................................................ 15

First Time Setup ................................................................................................................................................................................ 15

Pairing / Learning Wall Switch (or Channel) ..................................................................................................................................... 15

Unpairing / Unlearning Wall Switch (or Channel) .............................................................................................................................. 15

Setting Upper and Lower Limits / Learning a New Position .............................................................................................................. 15

Tug Command Mode ....................................................................................................................................................................... 15

Teleshade Installation Instructions ...................................................................................................................................................... 16

FCC ................................................................................................................................................................................................... 17

INDUSTRY CANADA ........................................................................................................................................................................ 17

Solarfective products are designed for use with Solarfective hardware and power supplies only. Install in compliance with all local and

national building and electrical codes. Always wear personal protection equipment including safety glasses and gloves. Use a ladder per

its manufacturer’s instructions.

Before installing the shade into the window, verify that window hardware (latches, locks, window cranks, etc.) does NOT obstruct the

travel path of the shade. Damage to the fabric or shade may result from repeated contact with windowhardware.

FALLING HAZARD: Shades must be installed to proper support structure.

Locate the shade’s mounting type on the order form (Inside Mount, Outside Mount).

Determine roll type (Standard Roll, Reverse Roll).

Fascia Brackets

For Standard Roll, the fabric rolls towards the window. The Motor Side Bracket is installed on the LEFT side of the window, and the

Spring Side Bracket is installed on the RIGHT side of the window. See Fascia Bracket Installation section for further detail.

For Reverse Roll, the fabric rolls toward the room. The Motor Side Bracket is installed on the RIGHT side of the window, and the

Spring Side Bracket is installed on the LEFT side of the window. See Fascia Bracket Installation section for further detail.

Universal Brackets

When installing Universal Brackets, the bracket mounting is the same for both Standard Roll and Reverse Roll. See Universal Bracket

Installation section for further detail.

Outside Mount

When installing the shade in an outside mount, use a measuring tape to measure and mark the Center Line of the window opening.

Divide the “Bracket to Bracket” width (found on order form) in half. Using the half width distance, measure and mark the distance on

each side of the center line. It is recommended to off-set the bottom of the brackets 1/2” above the window opening (see illustration

below).

CAUTION: READ AND UNDERSTAND EACH SECTION BEFORE PERFORMING

REQUIRED STEPS. FAILURE TO FOLLOW PROPER PROCEDURE

COULD RESULT IN DAMAGE TO THE SHADE OR PERSONAL INJURY.

Center Line

1/2”

Outside Mount

Inside Mount

FASCIA BRACKET HARDSTOP REMOVAL

When installing an outside mount, it is helpful to remove the hard

stop before screwing the bracket to the wall. Hard Stop MUST be

replaced for proper shade function.

The hard stop is easily removed by using a flat head screw driver.

Insert the flat head screw driver between the back of the hard stop

and the bracket (see illustration to right).

Apply a slight downward force to the top of the hard stop, while

using the flat head screwdriver to eject each of the three prongs

holding the hard stop in place.

The hard stop prong should slide down and out. After all three

prongs have been ejected, the hard stop can be tilted away from

the bracket for complete removal.

Replace the hard stop after mounting the bracket with the screws.

Make sure that both the top and bottom of the hard stop are

securely locked back in place. Failure to correctly replace the hard

stop will result in improper shade function or damage.

FASCIA BRACKET INSTALLATION

Position the bracket flush against the side and top of the window opening. Ensure brackets are level and square. Screw placement can

be through the side of the bracket, or through the top of the bracket (see illustrations). Fascia brackets should be recessed 1/8” (3mm)

into the window opening. This allows the fascia to be flush with the window opening when installed.

Use a pencil to mark the drill locations. With the brackets removed, use a 3/32” (2mm) drill bit to drill a pilot hole at each pencil mark.

Replace the brackets, and secure them to the wall using the pre-drilled pilot holes and provided screws. Use wall anchors if necessary

(not provided). Cable management shown (not provided).

Inside Mount – Standard Roll

Fascia Bracket Hardstop Removal

(Spring Side Bracket Shown)

1/8”

Inside mount - Standard Roll

Motor Side Bracket - Left Side

Side Screw Mount

Inside mount - Standard Roll

Spring Side Bracket -Right Side

Side Screw Mount

1/8”1/8”

Inside mount - Standard Roll

Motor Side Bracket - Left Side

Top Screw Mount

Inside mount - Standard Roll

Spring Side Bracket -Right Side

Top Screw Mount

Inside Mount – Reverse Roll

1/8” 1/8”

Inside mount - Reverse Roll

Spring Side Bracket - Left Side

Side Screw Mount

Inside mount - Reverse Roll

Motor Side Bracket -Right Side

Side Screw Mount

Outside Mount – Standard Roll

1/2” 1/2”

Outside mount - Standard Roll

Motor Side Bracket - Left Side

Hard Stop Removed

Outside mount - Standard Roll

Spring Side Bracket -Right Side

Hard Stop Removed

1/8”1/8”

Inside mount - Reverse Roll

Spring Side Bracket - Left Side

Top Screw Mount

Inside mount - Reverse Roll

Motor Side Bracket -Right Side

Top Screw Mount

Outside Mount – Reverse Roll

1/2” 1/2”

Outside mount - Reverse Roll

Spring Side Bracket - Left Side

Outside mount - Reverse Roll

Motor Side Bracket -Right Side

QIS CABLE PLACEMENT

Failure to properly orient and secure the QIS Cable may lead to damage of the shade or window enclosure. Cable

should be routed atop of the shade fabric tube (see illustration below). Make sure the bracket spacing provides enough room

to prevent pinching of the cable. Secure the cable using zip-ties or other cable management hardware so that the cable

does not interfere with shade operation.

CORRECT Cable Orientation INCORRECT Cable Orientation

SHADE INSTALLATION

Once the brackets are installed level and square, insert the shade into the bracket starting with the motor side. Make sure the spindle is

securely seated into the spindle key-hole (see illustration above). Improperly seated motors will cause issues with shade movement.

Once the motor side is in place, lift the spring side up into the bracket. The spindle should push against the bracket spring clip while

inserting the shade. When the spindle has cleared the spring clip, the spring clip will spring back locking the spindle into place. Rotate

the shade to ensure both spindles are fully seated into the slots.

1/2” 1/2”

1. Insert the Fascia at an angle, hook the Fascia onto the front edge of both top bracket arms.

2. Rotate the Fascia down, the Fascia should pivot on the front edge of the brackets in Step 1.

3. Firmly push the Fascia against the bracket, the Fascia will snap onto the bottom edge of the bracket.

Reverse Fascia

FASCIA INSTALLATION

Standard Fascia

1. Insert the Fascia at an angle, hook the Fascia onto the front edge of both top bracket arms.

2. Rotate the Fascia down, the Fascia should pivot on the front edge of the brackets in Step 1.

3. Firmly push the Fascia against the bracket, the Fascia will snap onto the bottom edge of the bracket.

NOTE: A single fascia center support is needed per 10 ft.(3m) of standard fascia, and two supports per 10 ft.(3m) of reverse fascia.

Install the fascia center support equally spaced between the brackets. Ensure that the fascia center support is level and square

to the top of the shade brackets.

UNIVERSAL BRACKET INSTALLATION

Inside Mount – Standard Roll

1/2”

Inside Mount - Standard Roll

Side Screw Mount - Left

Offset brackets 1/2 inch (13mm) from top of the window to

allow proper clearance for installing shade into bracket

Inside Mount - Standard Roll

Side Screw Mount - Right

Offset brackets 1/2 inch (13mm) from top of the window to

allow proper clearance for installing shade into bracket

1/8”1/8”

Inside Mount - Standard Roll

Top Screw Mount - Left

Inside Mount - Standard Roll

Top Screw Mount - Right

Illustrations above show mounting option for Universal Brackets using an inside mount. Universal Brackets can be mounted using

the side screw holes (see top illustrations). Universal Brackets can also be adjusted for mounting using the alternate screw holes by

removing the four screws and re-orienting the hard stop sub-bracket (see bottom illustrations).

Inside Mount – Reverse Roll

1/2” 1/2”

Inside Mount - Reverse Roll

Side Screw Mount - Left

Offset brackets 1/2 inch (13mm) from top of the window to

allow proper clearance for installing shade into bracket

Inside Mount - Reverse Roll

Side Screw Mount - Right

Offset brackets 1/2 inch (13mm) from top of the window to

allow proper clearance for installing shade into bracket

1/2” 1/2”

Inside Mount - Reverse Roll

Side Top Mount - Left

Offset brackets 1/2 inch (13mm) from back of the window to

allow proper clearance for installing shade into bracket

Inside Mount - Reverse Roll

Side Top Mount - Right

Offset brackets 1/2 inch (13mm) from back of the window to

allow proper clearance for installing shade into bracket

Illustrations above show mounting option for Universal Brackets using an inside mount. Universal Brackets can be mounted using

the side screw holes (see top illustrations). Universal Brackets can also be adjusted for mounting using the alternate screw holes by

removing the four screws and re-orienting the hard stop sub-bracket (see bottom illustrations).

Outside Mount - Standard Roll

1/2”1/2”

Outside Mount - Standard Roll

Left Side

Offset brackets 1/2 inch (13mm) from top of the window

Outside Mount - Standard Roll

Right Side

Offset brackets 1/2 inch (13mm) from top of the window

Outside Mount - Reverse Roll

1/2”

Outside Mount - Reverse Roll

Left Side

Offset brackets 1/2 inch (13mm) from top of the window

Outside Mount - Reverse Roll

Right Side

Offset brackets 1/2 inch (13mm) from top of the window

FASCIA END CAP INSTALLATION

To install Fascia End Caps, match the appropriate End Cap to the

correct bracket. End Caps are labeled Left or Right. Align the End

Cap posts (see illustration) with the side mount fastener locations

and snap the Fascia End Cap into the bracket.

For reverse fascia installations, the Fascia End Caps should be

reversed to fit the corresponding brackets.

NOTE: Note: If the brackets have been installed using the side

screw mount (flush against the window jamb) Fascia End

Caps will not be installed.

UNIVERSAL END CAP INSTALLATION

End caps are intended for use when the shade is OUTSIDE

mounted. Use in an INSIDE mounted shade will cause damage

to the shade by placing undue pressure on the shade from the

sides.

To install Universal End Caps, slide the End Cap onto the

Universal Bracket using the notched grooves for alignment (see

illustration). The Universal End Cap will fit onto either bracket.

NOTE: Note: If the brackets have been installed using the side

screw mount (flush against the window jamb) Universal

End Caps will not be installed.

QIS POWER & COMMUNICATION PANEL SETUP

CAUTION

The Qadvanced Intelligent System (QIS) does not operate on “standard” Power of Ethernet (PoE) schemes. Do not attempt to connect the

QIS to any PoE device or RJ-45 PoE port. Doing so will damage the system components and/or the external Ethernet or PoE device.

Power Port Communication Port

(RS485)

Device Port

(Shades and Switches)

Use CAT5e/CAT6 wire to connect QIS shades to the Power & Communication Panel. Terminate wires using RJ-45 connectors (T568B

Standard). QIS shades will Jog upon connecting power to the shade. The Amber LEDs on the Power & Communication Panel (RJ-45)

ports signify “power” is active. The Green LEDs signify communication activity.

To daisy chain additional QIS Power & Communication Panels, use either or the Communication Ports (RS485) to expand the system

capabilities up to 200 devices. ZigBee Ha1.2 capabilities allow up to 60 ZigBee devices on a ZigBee network.

Wire Specication:

• Category 5e/Category 6 for use with RJ-45 Connector

• 24 AWG

Maximum length of wire from Power & Communication Panel to device:

• Up to an 8’ X 8’ Shade with 40:1 motor - 1250’

• 8’ X 8’ to 12’ X 12’ Shade with 73:1 motor - 750’

Maximum length or wire for Hardwired 4 and 8 Button Switches:

• 1000’ feet from switch to farthest power panel

Maximum wire length for RS485 communication:

• 2000’ feet from source to shade

System Capacity:

• 200 Devices (Solarfective Shades, Solarfective Hardwired Switches)

Power & Communication Panel:

• 8 RJ-45 device ports for motorized shades and switches

• 2 additional RJ-45 communication ports dedicated to daisy chain with other

Power & Communication Panels and Third Party Integration via RS485

• Power Supply Port - AC Input: 100-240 VAC, 2.5A

• DC Output: 24 VDC, 7.5A

Wiring for Cat 5e/6 Cable

Pin Wire Color Signal 10/100BaseTx

1 White/Orange A+

2 Orange B-

3 White/Green +24 VDC

4 Blue +24 VDC

5 White/Blue +24 VDC

6 Green -24 VDC

7 White/Brown -24 VDC

8 Brown -24 VDC

QIS WALL SWITCH PROGRAMMING INSTRUCTIONS

First Time Setup

IMPORTANT – Read and understand each section before performing required steps. When using a Dual Channel Wall Switch, the left

button column corresponds to Channel 1. The right button column corresponds to Channel 2 as shown in the diagram below.

1. INSTALL SHADE following appropriate installation instructions

2. CONNECT POWER SUPPLY to Power Communication Panel

3. CONNECT SHADE to Power Communication Panel using network cable

(Shade will JOG on initial power-up)

4. CONNECT WALL SWITCH to Power Communication Panel using network cable

Pairing / Learning Wall Switch (or Channel)

1. PRESS both UP and PRESET 1 at the same time

(Shade will JOG in response)

2. TUG the HEMBAR 6-10 inches

(Shade will JOG in response and is now paired)

Unpairing / Unlearning Wall Switch (or Channel)

1. PRESS both DOWN and PRESET 2 at the same time

(Shade will JOG in response)

2. TUG the HEMBAR 6-10 inches

(Shade will JOG in response and is now unpaired)

IMPORTANT – When learning new positions, the button currently being programmed (after Step 3. TUG) will not send commands to the

shade.

Example 1: When learning a new PRESET 1 position, pressing PRESET 1 will do nothing (after Step 3. TUG). The shade can still be

adjusted using the UP and DOWN buttons.

Example 2: When learning a new upper limit position, the UP button is semi-disable. Only by pressing the UP button 3 times will the

shade move to the up position (or manually roll the shade up by hand). After Step 5 all buttons resume full functionality.

Setting Upper and Lower Limits / Learning a New Position

(You must use a paired wall switch to perform this task.)

1. PRESS the (UP or DOWN) button that will be programmed (Shade will move to selected position)

2. PRESS and HOLD the same (UP or DOWN) button UNTIL shade JOGS

3. TUG shade 6-10 inches (Shade will JOG in response)

4. ADJUST shade to desired position ( Use UP/DOWN buttons or manually adjust shade by hand)

5. PRESS and HOLD the same (UP or DOWN) button (Shade will JOG when learned)

Tug Command Mode

Tug Command Mode will allow certain features to be performed manually without a learned remote.

IMPORTANT – Read the following instructions completely before starting the procedure. Inputs from the user are time sensitive. If the

shade times out before entering a tug command, return the shade to the Upper Limit Position and begin the procedure over.

To Enter Tug Command Mode

1. Start with the shade at the Upper Limit Position.

2. Perform two consecutive 6 inch tugs, waiting 1 second between tugs.

(Shade will JOG, then travel up, settling a few inches below the Upper Limit Position)

The shade is now in Tug Command Mode There is a 10 second opportunity to enter a tug command before the shade will leave

Tug Command Mode and resume normal operation.

3. Once the shade is in Tug Command Mode, perform additional 6 inch tugs to select a command option. After each tug, the shade

will return to its starting position. Once the shade returns to its starting position, wait 1 second before performing the next tug (a

brake is engaged during this 1 second wait, making the shade difficult to tug). After the tug sequence is performed (1-4 Tugs), wait

5 seconds and the shade will accept the tug command.

• 2 Tugs - Set Lower Limit Position

• 4 Tugs - Factory Master Reset

CH 2CH 1

Dual Channel

Wall Switch

Single Channel

Wall Switch

TELESHADE INSTALLATION INSTRUCTIONS

CAUTION – Be sure to follow all

appropriate safety guidelines, including

the use of safety glasses and ensure

to keep the shade fabric clean by using

clean gloves whenever touching it.

Tools Required:

• Flathead Screwdriver

• Pliers

• Suitable #8 Pan Head Screws (4 per shade)

• Safety Glasses

• Gloves

Fig. 1

Snap-In Clip on Teleshade

Fig. 2

Mounting Angle for Face

or Ceiling Mount

Fig. 3

Align Snap-In Clip

to Mounting Angle

Fig. 4

Push Snap-In Clip Up

to Install Shade Using

Screwdriver, if Needed

CLICK

Fig. 5

To Remove Shade

Place a Screwdriver

Between Clips and Twist

1. If mounting into drywall, use a plastic anchor to securely fasten mounting angle to

mounting surface.

Note that mounting angles must be attached to at least 3/4” less than the full width of

the shade so not to interfere with the plastic housings at either end of the shade.

Attach the mounting angles as shown in Fig. 2.

2. Align the inside clip on the shade with the mounting angle, as shown in Fig. 3.

3. Tilt the shade back to level position, as shown in Fig. 4 to allow the tongue on the

inside clip to snap into the groove on the mounting angle.

If tongue and groove do not make an audible click to indicate connection, use a

screwdriver to push up behind fabric roll onto inside of clip on shade. This will push

the tongue into the groove and ensure a solid mount.

4. Once the shade is securely clipped into the mounting angles on each side, the stop

bead to set the lower limit of the shade can be attached to the bead chain with a pair

of pliers.

The stop bead should be set so that the bottom hembar is approximately 1/2” above

the sill.

5. The shade can be taken down by inserting a flat screwdriver into the gap between

the inside clip and the mounting angle and twisting, as shown in Fig 5.

FCC

Warning: Changes or modifications to this device not expressly approved by Solarfective® could void the user’s authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or

operating in conjunction with any other antenna or transmitter.

INDUSTRY CANADA

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain

approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be

so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et

d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage

radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope

rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter

tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

QdR REMOTE

Model: QZR-ZIG2400

FCC ID: 2ABLX-ZIG24DECO

IC: 8832A-ZIG24DECO

ROLLER SHADE

Model: QMRS-240Z

FCC ID: 2ABLX-240Z

IC: 8832A-240Z

European Representative

Doug Fiske

Contact for QMotion

Raritan Europe B.V.

Jan van Galenstraat 59

3115 JG Schiedam

The Netherlands

800.879.8585

www.legrand.us/solarfective

No. SF-QISInst – 08/18 rev. 1

LIMITED WARRANTY

Manufacturer warrants that this window shade product, and/or specific components of the window shade product, will be free from defects in materials

and workmanship for the period of time specified herein. Beginning from the date first sold to the commercial or residential consumer (either, the “Buyer”)

who has, or intends to, use the product, as evidenced by such Buyer’s proof of purchase, this Limited Warranty, as applicable to the specified product or

component, as such product or component is defined by Manufacturer, will be in effect for the time periods set forth below:

• For all motorized products, controls and electronic accessories: 5 (five) years

• For all manual products and controls: 5 (five) years

• For fabrics used in shades, if procured and supplied by Manufacturer as part of a roller shade: 5 (five) years

Exclusions From this Limited Warranty: This Limited Warranty shall be null and void and no part of it shall apply if any one of the followingoccur: 1) the

product has not been properly installed by a qualified installer in accordance with all Manufacturer specifications; 2) theproduct has been subject to

unauthorized service; 3) the product has been subject to mishandling, misuse, or abuse; 4) the product has been modified;5) the product has suffered

damage resulting from lightning, power surges, vandalism, fire, earthquake, acts of nature, or any other cause which the product was not designed to

withstand; 6) the product has been used, or attempted to be used, for other than the customary usage or for other than the product’s intended use; 7) the

product has not been maintained in accordance with Manufacturer’s instructions; 8) damage to the product caused by battery decay or corrosion.

This Limited Warranty extends only to the original owner and is only valid if the product or component is purchased either directly from Manufacturer or

an authorized reseller. This Limited Warranty is not transferable. This Limited Warranty does not cover normal wear or tear or deterioration which occurs

with the passage of time.

Batteries originally provided with a new product, if any, are produced by a third party and are not warranted by Manufacturer. No employee, distributor,

dealer, agent or representative is authorized to change the terms of this Limited Warranty in any way, to extend the warranty time periods, or to grant

additional warranties, and no attempt to do any of the foregoing will be binding upon Manufacturer.

IF THIS LIMITED WARRANTY COVERS A CONSUMER PRODUCT, AS DEFINED BY THE MAGNUSON-MOSS WARRANTY ACT AND APPLICABLE

CANADIAN CONSUMER PROTECTION LAWS, THEN NO WARRANTIES, EXPRESSED OR IMPLIED (INCLUDING, BUT NOT LIMITED TO, THE

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) SHALL EXTEND BEYOND THE APPLICABLE TIME PERIOD

STATED IN BOLD FACE TYPE ABOVE. IF THIS LIMITED WARRANTY COVERS A COMMERCIAL PRODUCT, THEN THIS LIMITED WARRANTY

IS IN LIEU OF ALL OTHER REPRESENTATIONS, GUARANTEES, OR OTHER EXPRESS OR IMPLIED WARRANTIES (INCLUDING, WITHOUT

LIMITATION, THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) AND ALL SUCH OTHER EXPRESSED OR

IMPLIED WARRANTIES ARE HEREBY SPECIFICALLY DISCLAIMED.

Claims for defects in material and workmanship covered by this Limited Warranty must be made in writing to the dealer from whom the product was

originally first purchased within the warranty period stated above. Manufacturer may either send a service representative or have the product returned

to Manufacturer’s facility, at Buyer’s expense, for inspection. If judged by Manufacturer to be defective in material or workmanship, and to otherwise be

covered by this Limited Warranty, the product will be replaced or repaired at the option of Manufacturer, in its sole and absolute discretion, free from

all charges except authorized transportation and replacement labor. Replacement labor, transportation costs, and any other costs or charges by the

dealer, wholesaler, distributor, contractor, or installer are not covered by this Limited Warranty. Any replacement unit may be a model determined by

Manufacturer to be equivalent to the defective model, or a product that has been factory refurbished. The remainder of original warranty period will apply

to any repair/replacement unit.

THE REMEDIES OF BUYER SET FORTH IN THIS LIMITED WARRANTY ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER REMEDIES. THE

LIABILITY OF MANUFACTURER WHETHER IN CONTRACT, TORT, UNDER ANY WARRANTY OR OTHERWISE, SHALL NOT EXTEND BEYOND

ITS OBLIGATION TO REPAIR OR REPLACE, AT ITS OPTION, ANY PRODUCT OR PART FOUND BY MANUFACTURER TO BE DEFECTIVE IN

MATERIAL OR WORKMANSHIP AND OTHERWISE SUBJECT TO THIS LIMITED WARRANTY. MANUFACTURER SHALL NOT BE RESPONSIBLE

FOR ANY DIRECT, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

This Limited Warranty gives specific legal rights and Buyer may have other rights, which may vary from jurisdiction to jurisdiction. However, some

jurisdictions do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the

above limitations or exclusions may not apply to specific Buyers.

For Warranty Service, contact us at:

Solarfective

55 Hymus Rd

Scarborough, ON M1L 2C6, Canada