Midmark Asepsis 21® Systems Installation guide

Asepsis 21® Systems
Midmark
Brand
Midmark
Model
Asepsis 21® Systems
Type
Installation guide

This manual is also suitable for

1 of 4
INSTALLATION INSTRUCTIONS
for the
Concept LR Cuspidor
Figure 1
VAC PACK
BUTTON HEAD SCREWS
AF1061
Figure 2
SECTION I - chair with
Vac Pack
Follow the steps in Section I and Section III if your
chair has the Vac Pack System already installed:
1. Remove the two button head screws from the
Vac Pack cover (See Figure 1).
2. Position the cuspidor assembly as shown and
Install it to the chair using the two socket head
screws provided (See Figure 2).
3. Run the umbilical from the cuspidor along the
side of the chair forward to the J box.
4. Go to Section III.
ARM ASSEMBLY
SOCKET HEAD SCREWS
AF1062
PLUGS
Print on plain white paper - Part # 122919 (FRONT & BACK & STAPLE)
Style A
2 of 4
SECTION II - chair
without
Vac Pack
Follow the steps in Section II and Section
III if your chair does not have the Vac
Pack System:
1. Remove the three Platform covers as
shown (See Figure 3). Discard the
center platform cover.
2. Insert the spacers provided in the
holes in the new platform cover and
position the cuspidor assembly as
shown. Install the assembly to the
chair platform using the two socket
head screws provided (See
Figure 4).
4. Replace the covers.
5. Run the umbilical from the cuspidor
along the side of the chair forward to
the J box.
6. Go to Section III.
Figure 3
Figure 4
PHILLIPS
HEAD
SCREWS
CENTER
PLATFORM
COVER
RIGHT
HAND
PLATFORM
COVER
LEFT
HAND
PLATFORM
COVER
AF1066
ARM ASSEMBLY
NEW PLATFORM COVER
SPACERS
SOCKET HEAD SCREWS
CHAIR PLATFORM
AF1068
PLUGS
3 of 4
Figure 5
Figure 6
UNIT
CUSPIDOR
CUSPIDOR
ASSISTANT'S
INSTRUMENTS
ASSISTANT'S
INSTRUMENTS
TYPE I
UMBILICAL
CLAMP
TYPE II
UMBILICAL
CLAMP
AF1064
SECTION III - J Box
Connections
1. Open the J box cover and remove the existing
umbilical clamp, screws and nuts. Discard
(See Figure 5).
NOTE: If your chair is internally
plumbed, use the Type I clamp to hold
the umbilicals to the J box.
If your chair is externally plumbed, use
the Type II clamp to hold the umblicals
to the J box.
2. Position the umbilicals in the approrate slots
in the new clamp as suggested
(See Figure 6).
3. Secure the umbilical clamp to the J box using
the wingnuts and washers provided
(See Figure 5).
4. Make the connections inside the J box as shown
(See Figure 7).
UMBILICAL
CLAMP
WASHER AND
WINGNUT
J BOX
EXISTING
UMBILICAL
CLAMP
EXISTING
SCREW AND
NUTS
WINGNUTS AND
WASHERS PROVIDED
TYPE I
UMBILICAL
CLAMP
TYPE II
UMBILICAL
CLAMP
AF1063
4 of 4
Figure 7
WATER
AIR
WASTE
ELECTRICAL
BOX
2" x 4"
BOX FOR
POWER
SUPPLY
(not supplied)
C
VACUUM
TO FOOT
CONTROL
1/4" CLEAR TUBE
DRIVE AIR OUT
1/8" ORANGE TUBE
COOLANT WATER
PILOT AIR
UMBILICALS
OPTIONAL
1/8" YELLOW TUBE
FOR CUSPIDOR
1/8" RED TUBE
PILOT AIR
MASTER VALVE
FOOT CONTROL
TUBING INLET AIR
(ribbed tube)
1/8" PURPLE TUBE
NON-CONTROLLED
AIR MASTER VALVE
1/8" BROWN TUBE
AIR TO DISTILLED
WATER BOTTLE
1/4" BLUE TUBE
CUSPIDOR
AIR
80 PSI
AIR AND WATER TUBING
CONNECT TO LABELED FITTINGS
ON THE UNDERSIDE OF THE
VALVE BLOCK
AIR REGULATOR
FOR DISTILLED
WATER BOTTLE
THESE
TUBES ARE
OPTIONAL
AND ARE
USED WITH
THE
CUSPIDOR
OR OTHER
OPTIONS
VALVE BLOCK
TUBING
FOR OPTIONS
WHITE
CLEAR
GREEN
BLUE
AF1065
TPW1718 Rev. B
Midmark Corporation P O Box 286 60 Vista Drive
Versailles Ohio 45380-0286 www.midmark.com
Phone: 937-526-3662 Fax: 937-526-5542
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Midmark Asepsis 21® Systems Installation guide

Asepsis 21® Systems
Midmark
Brand
Midmark
Model
Asepsis 21® Systems
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents