Eurotherm 808/847 & 809/849 Installation guide

MODEL

808/847

UNIVERSAL PID PROGRAMMER/CONTROLLER

MODEL

809/849

THREE-STATE VALVE POSITIONER

PROGRAMMER/CONTROLLER

Contents

Chapter 1

SAFETY,

EMC

AND GENERAL

INFORMATION

Safety..........................1-1

1

Electromagnetic compatibility.

............ 1-l

GENERAL

........................... l-l

Unpacking and storage

................. l-l

General description

....................

1

-

1

SERVICE AND REPAIR.

..................l-2

Cleaning.

........................... l-2

INSTALLATION SAFETY REQUIREMENTS.

....

l-3

Safety symbols.

.......................

1-3

Personnel

........................... l-3

Enclosure of live parts

.................. l-3

Wiring.

............................. l-3

Power isolation

....................... l-3

Earth leakage current.

.................. l-4

Overcurrent

protection.

................. l-4

Voltage rating

........................ l-4

Conductive pollution

................... l-4

Over-temperature protection

.............

l-4

Grounding of the temperature sensor shield . . l-5

INSTALLATION REQUIREMENTS FOR

EMC

... l-5

Routing of wires.

...................... l-5

Chapter 2

INSTALLATION

Dimensions and panel mounting

.......... 2-l

Electrical connections. .................. 2-2

Connecting terminals.

.................. 2-3

Mains supply and earth

................. 2-3

Output 1.

.......................... .2-4

Output 2.

........................... 2-4

Output 3, Alarm

...................... 2-7

Input. ..............................

2-7

Thermocouple input.

................... 2-7

808/847

&

809/849

Installation and Operating Instructions

HA021 428

Iss

8

Cont.i

Chapter 3

Chapter 4

Chapter 5

Chapter 6

Chapter 7

Chapter 8

Resistance thermometer (RTD)

Pt1

00,

three-wire device.

.....................

2-8

Linear input (Option QLS

.

...)

.............. 2-8

Digital communications (option) ........... 2-9

Programmer/controller (option QP...),

setpoint

programming option. ...........

2-1 1

TECHNICAL SPECIFICATION

PRODUCT CODE

OPERATION

Operating structure ....................

5-

1

Operating modes

....................

.5-2

Control algorithms.

....................

5-2

Front panel identification ................ 5-3

Operating procedures

..................

5-5

Alarms

............................

.5-7

Sensor break.

.......................

.5-8

Self-test.

............................

5-8

CONFIGURATION LEVEL, OPERATOR LEVEL

Configuration link/switch

...............

.6-1

Hardware configuration ................ .6-2

Parameter list .......................

.6-3

Pre-configuration, parameter setting ...... .6-10

Cutback

..........................

.6-10

PARAMETER ACCESS AND CALIBRATION

Parameter access protection.

.............

7-1

Calibration

..........................

7-2

PROGRAMMER/CONTROLLER

Programmer/controller

-

Function. .........

8-1

Programmer/controller

-

States............ 8-2

Programmer/controller

-

Holdback. ........ 8-3

Programmer/controller

-

-Setpoint

programming

..................................

8-4

Programmer/controller

-

Annunciators ......

8-5

Programmer/controller

-

Parameter

modification .........................

8-5

Ending a program. ....................

8-6

Program recovery following loss of power. . . . 8-7

Cont.ii

808/847

&

809/849 Installation and Operating Instructions

Chapter 9

SELF-TUNING

Self-tuning

-

General. .................. 9-l

Self-tuning

-

Activation. .................

9-2

Self-tuning

-

Operation ................. 9-2

Self-tuning

-

Abort conditions.

............ 9-7

Chapter 10

INSTRUMENT REGISTER

Chapter 11

SUPPLEMENTS- Relating to

808/809

valve

positioner controllers

Valve positioner controller (motor open/close) 1 1

-

1

Additional parameters for valve positioner

controller . . , . . . . . . . . . . . . . . . . . . . . . . . 11-2

Self-tuning for valve positioner controller . . . 11-2

808/847

&

809/849

installation and Operating Instructions

Cont. iii

General

SAFETY, EMC AND GENERAL INFORMATION

Please read this section carefully before installing the controller

This controller is intended for industrial temperature and process control applications when it

will meet the requirements of the European Directives on Safety and EMC. Use in other

applications, or failure to observe the installation instructions of this handbook may impair the

safety or EMC protection provided by the controller. It is the responsibility of the installer to

ensure the safety and EMC of any particular installation.

Safety

This controller complies with the European Low Voltage Directive 73/23/EEC, amended by

93/68/EEC, by the application of the safety standard EN 61010.

Electromagnetic compatibility

This controller conforms with the essential protection requirements of the EMC Directive

89/336/EEC, amended by 93/68/EEC, by the application of a Technical Construction File.

This instrument satisfies the general requirements of an industrial environment as described by

EN 50081-2 and EN 50082-2. For more information on product compliance refer to the

Technical Construction File.

GENERAL

The information contained in this manual is subject to change without notice. While every

effort has been made to ensure the accuracy of the information, Eurotherm Controls shall not

be held liable for errors contained herein.

Unpacking and storage

If on receipt, the packaging or the instrument are damaged in any way, do not install or

commission the product. Contact your nearest Eurotherm Controls agent as soon as possible.

If the instrument is to be stored before use, protect from humidity and dust in an ambient

temperature range of -30°C to +75 deg C.

The packaging should contain an instrument mounted in its sleeve, two mounting brackets for

panel installation and this operating book. Certain ranges are supplied with an input adapter.

General description

Models 808 and 847 are digital temperature controllers. The 809 and 849 are valve position-

ing controllers. The 808 and 809 are mounted upright, (vertical) and the 847 and 849 are

mounted

on

their side (horizontal).

Two LED displays indicate the operating parameters. The top display indicates the actual

value, (PV) and the lower display indicates the setpoint, (SP). Other LED beacons indicate

the mode of operation, (see Chapter 5, Operation).

Parameters and configuration values are set by use of the front panel keys. The PAR button

selects the parameter and the up and down arrows are used to alter their value. In configura-

tion mode each parameter can be defined as ‘read only ,

’

‘read

/

write’ or ‘hidden’. The

controller can be switched directly from automatic (closed loop) operation to manual by

means of the A/M button.

808/847

&

809/849

Installation and Operating Instructions

l - l

General

Without change of the hardware the main process variable input of the instrument can be

configured to suit various thermocouples and resistance thermometers, (PtlOO). Recalibration

is not necessary for this procedure. Signals up to 25V can be accommodated by using input

adapters in the linear input option. Linearisation is scaleable within the display range of -999

to 9999, with tenths display resolution.

The controller is also equipped with a ramp to setpoint function. This enables it to automati-

cally adjust the setpoint to give a defined rate of change of the process temperature. In the

programmer version, two ramps and two dwell periods may be set.

The modular construction of the instruments allows up to three output channels to perform

various functions. The instrument can be configured as a heat cool controller with one alarm,

or a heat only controller with two alarms. The heat output may be fitted with a dc output.

For communications with a host computer system the instrument can be fitted with either an

EIA 232 or EIA 422 digital interface. This enables the automatic recording of measured

values on a printer, or the use of a proprietary supervisory system such as Eurotherm Controls

ESP package.

SERVICE AND REPAIR

This controller has no user serviceable parts. Contact your nearest Eurotherm Controls agent

for repair.

Caution: Charged capacitors

Before removing an instrument from its sleeve, disconnect the supply and wait at least two

minutes to allow capacitors to discharge. Failure to observe this precaution will expose

capacitors that may be charged with hazardous voltages. In any case, avoid touching the

exposed electronics of an instrument when withdrawing it from the sleeve.

Electrostatic discharge precautions

When the controller is removed from its sleeve, some of the exposed electronic components

are vulnerable to damage by electrostatic discharge from someone handling the controller. To

avoid this, before handling the unplugged controller discharge yourself to ground.

Cleaning

Clean the instrument sleeve and the front facia with an anti-static cleaner and a soft cloth.

Do not use water or water based products to clean labels or they will become illegible.

Isopropyl alcohol may be used to clean labels.

1-2

808/847

&

809/849

Installation and Operating Instructions

General

lNSTALLATlON SAFETY REQUIREMENTS

Safety Symbols

Various symbols are used on the instrument, they have the following meaning:

Caution, (refer to the

I Functional earth

.

accompanying documents) (ground) terminal

The functional earth connection is not required for safety purposes but to ground RFI filters.

Personnel

Installation must only be carried out by qualified personnel,

Enclosure of live parts

To prevent hands or metal tools touching parts that may be electrically live, the controller

must be installed in an enclosure. It is recommended that you use the rear terminal cover pro-

vided.

Caution: Live sensors

The fixed digital input and the non-isolated dc and logic outputs, are all electrically connected

to the main process variable input. If the temperature sensor is connected directly to an elec-

trical heating element then these non-isolated inputs and outputs will also be live. The con-

troller is designed to operate under these conditions. However you must ensure that this will

not damage other equipment connected to these inputs and outputs and that service personnel

do not touch connections to these i/o while they are live. With a live sensor, all cables, con-

nectors and switches for connecting the sensor and non-isolated inputs and outputs must be

mains rated.

Wiring

It is important to connect the controller in accordance with the wiring data given in this hand-

book.

.

Take particular care not to connect AC supplies to the low voltage sensor input or other

low level inputs and outputs.

.

Only use copper conductors for wiring connections, (except for thermocouple inputs).

.

Ensure that the wiring of installations comply with all local wiring regulations. In the

UK use the latest version of the IEE wiring regulations, (BS 767 1). In the USA use

NEC Class 1 wiring methods.

Unused terminals should not be used as ‘tie points’.

.

Ensure the correct polarity of signal connections.

Power Isolation

The installation must include a power isolating switch or circuit breaker. This device should

be in close proximity to the controller, within easy reach of the operator and marked as the

disconnecting device for the instrument.

808/847

&

809/849

installation and Operating Instructions 1-3

General

Earth leakage current

Due to RFI Filtering there is an earth leakage current of less than 0.5mA This may affect the

design of an installation of multiple controllers protected by Residual Current Device, (RCD)

or Ground Fault Detector, (GFD) type circuit breakers.

Overcurrent protection

To protect wiring and the PCB tracking within the controller against excess currents, the AC

power supply to the controller and power outputs must be wired through the fuse or circuit

breaker specified in the technical specification.

Voltage rating

The maximum continuous voltage applied between any of the following terminals must not

exceed 264Vac:

.

line or neutral to any other connection;

.

relay or triac output to logic, dc or sensor connections;

.

any connection to ground.

The controller should not be wired to a three phase supply with an unearthed star connection.

Under fault conditions such a supply could rise above 264Vac with respect to ground and the

product would not be safe.

Voltage transients across the power supply connections, and between the power supply and

ground, must not exceed 2.5kV. Where occasional voltage transients over 2.5kV are expected

or measured, the power installation to both the instrument supply and load circuits should

include a transient limiting device.

These units will typically include gas discharge tubes and metal oxide varistors that limit and

control voltage transients on the supply line due to lightning strikes or inductive load switch-

ing. Devices are available in a range of energy ratings and should be selected to suit condi-

tions at the installation.

Conductive pollution

Electrically conductive pollution must be excluded from the cabinet in which the controller is

mounted. For example, carbon dust is a form of electrically conductive pollution. To secure a

suitable atmosphere in conditions of conductive pollution, fit an air filter to the air intake of

the cabinet. Where condensation is likely, for example at low temperatures, include a thermo-

statically controlled heater in the cabinet.

Over-temperature protection

When designing any control system it is essential to consider what will happen if any part of

the system should fail. In temperature control applications the primary danger is that the heat-

ing will remain constantly on. Apart from spoiling the product, this could damage any process

machinery being controlled, or even cause a fire.

Reasons why the heating might remain constantly on include:

.

the temperature sensor becoming detached from the process;

thermocouple wiring becoming short circuit;

.

the controller failing with its heating output constantly on;

l-4

808/847

&

809/849

Installation and Operating Instructions

General

.

an external valve or contactor sticking in the heating condition;

.

the controller setpoint set too high.

Where damage or injury is possible, we recommend fitting a separate over-temperature protec-

tion unit, with an independent temperature sensor, which will isolate the heating circuit.

Please note that the alarm relays within the controller will not give protection under all failure

conditions.

Grounding of the temperature sensor shield

In some installations it is common practice to replace the temperature sensor while the con-

troller is still powered up. Under these conditions, as additional protection against electric

shock, we recommend that the shield of the temperature sensor is grounded. Do not rely on

grounding through the framework of the machine.

INSTALLATION REQUIREMENTS FOR EMC

To ensure compliance with the European EMC directive certain installation precautions are

necessary as follows:

.

For general guidance refer to Eurotherm Controls EMC Installation Guide,

HA025464.

.

When using relay or triac outputs it may be necessary to fit a filter suitable for sup

pressing the emissions. The filter requirements will depend on the type of load. For

typical applications we recommend Schaffner FN321 or FN612.

s

If the unit is used in table top equipment that is plugged into a standard power socket,

then it is likely that compliance to the commercial and light industrial emissions

standard is required. In this case to meet the conducted emissions requirement, a

suitable mains filter should be installed. We recommend Schaffner types FN32

1

and

FN612.

Routing of wires

To minimise the pick-up of electrical noise, the wiring for low voltage dc and particularly the

sensor input should be routed away from high-current power cables. Where it is impractical to

do this, use shielded cables with the shield grounded at both ends. In general keep cable

lengths to a minimum.

808/847

&

809/849

Installation and Operating Instructions

l-5

installation

INSTALLATION

Before installing this product read the safety and EMC information

Dimensions and panel mounting

The instrument is intended to be mounted into a front panel cut-out. Figure 2.1.1 shows the

dimensions of the instrument and of the necessary front panel cut-out with tolerances. Behind

the instrument sufficient space should be provided for wiring.

+0.60

45mm

-o.oo

96mm

Front panel cut-out

Maximum thickness 6mm

Figure 2.1.1 Dimensions and panel cut-out

Ventilation:

The space behind the control panel must be sufficient to allow suitable ventila-

tion to keep the ambient temperature within the permitted range.

To assemble, turn the screw on the front fascia in an anti-clockwise direction and pull the

instrument out of the sleeve. Now slide the plug-in sleeve into the control panel cut-out from

the front. The two mounting brackets are fastened on the left and right hand side behind the

control panel and tightened with a screwdriver in a clockwise direction. A torque limiter pre-

vents over-tightening.

For multiple installation in a control panel, the minimum spacings specified in Figure 2.1.2

must be respected for adequate cooling.

In order to install the instrument to meet the NEMA3 rating (IEC IP54), an additional gasket

kit is necessary. The kit consists of two self-adhesive neoprene gasket rings, these seal the

instrument to the instrument sleeve, and the sleeve to the front panel. The order number for the

gasket kit is LA022339.

808/847

&

809/849

Installation and Operating Instructions 2-1

installation

at least

50mm

at least

50mm

Figure 2.1.2 Minimum spacings for multiple installation

Electrical connections

When wiring electrical equipment, please refer to the instructions in Chapter

1,

Safety, EMC

and General Information and Chapter 3 Technical Specification.

Before wiring, verify from the instrument label (on the side) which options have been built

into the instrument and how the instrument is configured.

The terminals at the rear of the instrument are numbered from 1 to 20. Terminal allocation is

shown in Figure 2.2.1.

WARNING

The instrument has no in-built mains switch and is therefore

powered when the supply voltage is applied.

Note: Each output fitted with a relay or triac is equipped with an RC suppressor (snubber).

Even when the output triac or relay is off, the snubber passes a current of 1mA when

connected in a 120V AC circuit and likewise 2mA in a 240V AC circuit. When testing one of

these outputs with a high input impedance voltmeter and the output is unloaded, the voltmeter

2-2

808/847

&

809/849

Installation and Operating Instructions

Installation

will read the line voltage even though the output is off. This does not indicate that the output

is faulty. Such a test should only be carried out when the output is loaded appropriately.

Logic o r D C

DC output 1 only)

OV(-)

Signal (+)

ov

(-)

Signal (+)

‘riac or Relay

RS-422-A

1

11

12

13

14

15

16

17

18

19

20

Common

I

4

5

6

7

Signal (+)

OV

(-)

RS-232-C

Common

TX

Override of communications

Front panel disable

initiated

Logic

Relay

I

Thermocouple/Linear

input (with input adapter)

Pt100

Figure 2.2.1 Terminal allocation

Connecting terminals

Mains supply and earth

The controller can be powered by a mains voltage between 85 and 264 V AC

/

50-60 Hz.

Connect the Neutral to terminal 6 and the Live to terminal 5. A minimum of 0.5mm2 or 16awg

wire is recommended. The earth ground of every single instrument should be directly connect-

ed to the equipment copper ground bar. Do not connect several earth grounds of an instrument

as a chain (“daisy-chain” connection).

Function External Connections

Terminals

Live

Neutral

Earth

2A

I

Switch mode

6

Power Supply

,

Figure 2.3.1 Mains supply, Terminals

5, 6

&7

808/847 &

809/849

Installation and Operating Instructions

2-3

Installation

output 1

Output 1 can be fitted with four output module types: triac

(Tl),

relay

(Rl),

logic

(Ll)

or DC

(Dl).

Check the relevant code on the instrument label. The external connections depend on the

type of output module installed. If output 1 is configured as time proportioned with power

feedback, the mains supply of the instrument must be connected to the same Live as the load

supply.

output 2

Output 2 can be fitted with four output module types: triac

(Tl),

relay (RI) or logic

(Ll)

or

DC(D1). Check the relevant code on the instrument label. The external connections depend on

the type of output module installed.

Output 2 is configurable as either the cool channel or an alarm channel. If it is configured as

an alarm channel, the output module cannot be a triac (Tl). In the alarm condition, the relay of

this alarm output is energised, i.e. in the event of power-down or mains failure etc., the alarm

relay does not operate. For this reason this alarm should not be used for critical alarm

applications (not failsafe).

The following diagrams show terminal allocation for outputs 1

&

2.

WARNING

The logic and dc outputs are not isolated from the

thermocouple input.

2-4

808/847

&

809/849

Installation and Operating Instructions

Installation

Function

Triac

(T1)

Triac conducts during

ON

Phase ( y e l l o w OP1 l a m p

ON)

Relay

(R1)

Relay c o n t a c t i s c l o s e d

luring ON phase (yellow

OP1

lamp ON)

Logic

(L1)

Logic output = +18V

Wing ON phase of

Output

cycle (yellow OP1

amp ON)

DC

(D1)

External Connections Terminals

Internal Device

To mains

80

-

264V AC

50/60Hz

ov

(-)

Logic signal (+)

+18V, m a x 1 10mA

DC signal (+)

4-20mA

/

0-20mA

Not

Isolated

from

thermo

Figure 2.3.2 Output 1, Terminals 1

&

2

808/847

&

809/849

Installation and Operating Instructions

2-5

Installation

Function

Trriac

(T1)

Cool

channel only

iac conducts during Oh

phase ( y e l l o w OP2 lamp

ON)

elay

channel

elay contact is closed

during ON phase (yellow

(OP2 lamp ON)

larm Output

Contacts energised

during alarm condition

(OP2 lamp ON)

Logic

Cool

channel

Logic output = +1

ON phase of

output cycle (yellow OP2

w

output

output =

alarm condition

OP2 lamp ON)

External Connections Terminals

To mains

,

ted

2A

To mains

I

80 264V

AC

I

Logic signal (+)

max.

Not

DC signal (+)

4-20mA O-20mA

Internal Device

Figure 2.3.3 Output 2, Terminals 3 4

Installation and Operating instructions

Installation

Output 3, Alarm

This alarm channel can be fitted with relay

(Rl)

or logic

(Ll)

output module types. Check the

relevant code on the instrument label. The external connections depend on the type of output

module installed.

When in the alarm condition, the alarm relay is de-energised. The alarm circuit connected

should be fused and designed to operate in a failsafe manner, even in the event of a blown

fuse.

In the alarm condition an appropriate annunciation appears on the LED display.

Function

External Connections

Terminals

Internal Device

Relay is de-energised

during alarm condition

Closed in alarm

condition

Open in alarm

. . . .

condition

9

I

I I

Common

10

Isolated from

thermocouple

input

I

Logic

(Ll)

Logic

(l1)

I

Logic output =

OV

Logic output =

OV

during alarm conditionduring alarm condition

Outputs = +I 8V (active,Outputs = +1 8V (active,

No connection

high) during non alarmhigh) during non alarm

conditioncondition

Logic signal (+)

.18V,

max.

10mA

Logic

Figure 2.3.4 Output 3, Alarm, Terminals 8, 9 10

Input

Thermocouple and RTD inputs can be connected to the measured value input of the instru-

ment, and linear input signals (millivolt and process signals with suitable input adapter) can

also be accommodated. For the possible types and ranges of input sensors, please refer to the

sections on Technical Data (Section 3) and Product Code (Section 4).

Thermocouple input

Connections between thermocouple and controller must be made with the appropriate

compensating cable. Sensor break detection and an internal CJC (cold junction compensation)

are built into the instrument. If the instrument is configured for external CJC, the connections

between the CJC and the controller must be made with copper wire. Verify that correct

polarity

is observed at the connection points.

808/847

&

809/849

Installation and Operating Instructions

2-7

installation

Resistance thermometer (RTD) Ptl 00, three-wire device

Connect the single wire of the sensor to terminal 19 and the double wire to terminals 18 20.

The length and gauge of all three wires must be equal. The cable resistance is compensated for

by the three-wire device. Sensor break display is shown only if two wires break

Sensor

External Connections

Terminals

no connection

Figure 2.3.5 Sensor input, Terminals 18, 19 20

Linear input (Option

For input signals in the range to connection is made directly to the instrument.

As a precaution against interference, a shielded, twisted pair should be used. The shield should

only be grounded at the sensor end.

For input signals greater than

and process signals (per unit signals), a suitable input

adapter is available. This adapter is delivered with the instrument if ordered. Make sure that it

is installed directly on to the instrument terminals. Again, use a shielded, twisted pair.

2-8

Installation and Operating Instructions

Installation

Process Signal

(Option

QLS

only

)

Voltage Adapter

-10 . . . +50mV NONE

-40

+200mV IAV2

-200

...

+1000mV

IA1V

-1 . . .

+5V

IA5V

-2

+10V

1A10V

-5 . . +25V

IA25V

Current

Adapter

-4

..

.+20mA IAA02

External

Connections

Input Adapter

Terminals

Adapter

TYP IA...

Controller

Terminals

Ground O

I

V.

in

t

Figure 2.3.6 Linear input, Terminals 18, 19

&

20

Digital communications (option)

Verify on the instrument label if an EIA232 or an EIA422 interface is installed.

EIA232:

Terminal 15 is for receiving (RX) and terminal 13 for transmitting (TX) on the

EIA232 communications board, terminal 11 is common, This communications board is

designed for point-to-point operation. Transmitting and receiving links are made between the

supervisory computer and the controller. The cable length should be limited to 15m.

EIA422:

Terminal 11 is common and should be connected via a ground conductor to the

supervisory computer chassis, as a precaution against interference. The EIA422 communica-

tions board uses terminals 14 (RX+) and 15 (RX-) for receiving and terminals 12 (TX+) and

13 (TX-) for transmitting. This communications board is designed for a maximum of 32

instruments. Cable lengths should be limited to a maximum of 1200m.

Front panel lock-out override:

If terminals 16

&

17 are connected together for a short

period, lockout induced by a supervisory computer may be overridden. This function is

necessary if an error has been made in communication with the supervisory computer, and

there is a need to operate the controller manually despite the front panel lock-out. Further

ways of overriding a lock-out are by switching the instrument off for a short period or by an

appropriate command from the supervisory computer.

808/847

&

809/849

Installation and Operating Instructions

2-9

Installation

If the instrument is configured as a programmer controller, terminals 16 17 no longer

serve as a lock-out override, but instead take on functions associated with the

programming option, see following sections.

The digital communications output is isolated from the thermocouple input.

Figure 2.3.7 shows terminal allocation for in-built digital communications.

Standard

Terminals

External Connections

for

‘rant-panel

Front pane/ enable

Supervisor

Keyswitch for

front-panel

lockout

override

Figure 2.3.7 Digital communications, Terminals 11 to 17

2-10

Installation and Operating Instructions

Installation

Programmer controller (Option QLPS), programming

option

If the instrument is configured as a programmer controller (see instrument label), the RUN

and HOLD states of a given program are controlled via terminals 16

17. Figure 2.3.8 shows

possible connections. The function of the programmer

controller is described in later sections

to start program (restart after HOLD/RESET)

HOLD/RESET

reset to beginning of program

and

hold

Model

Option

A.

Switch

6.

logic with opto-coupler

C. Self-latching relay circuit

Figure 2.3.8 programming option, Terminals 16 17

WARNING

The logic input are not isolated from the thermocouple

input.

Installation and Operating Instructions 2-11

Technical Specification

TECHNICAL SPECIFICATION

Environmental ratings

Panel sealing:

Operating temperature:

Relative humidity:

Atmosphere:

Equipment ratings

Supply voltage:

Supply frequency:

Power consumption:

Relay (isolated):

Triac outputs (isolated):

Leakage current:

Over current protection:

Low level i/o:

Logic output (Non-isolated):

DC output (Non-isolated):

Fixed digital input:

Digital Communications:

Address range:

Baud rate:

Character format:

General

Dimensions:

Weight:

Resolution:

Sample rate:

Common mode rejection:

Calibration accuracy:

Cold junction compensation:

Maximum lead resistance:

Thermocouples:

Thermocouple linearisation:

Instruments are intended to be panel mounted. The rating of panel

sealing is IP54, (EN 60529), or NEMA 3 when used with the optional

gasket kit, part number LA 022339.

0 to 50°C. Ensure the enclosure provides adequate ventilation.

5 to 95%, non condensing.

The instrument is not suitable for use above 2000m or in explosive or

corrosive atmospheres.

85

to 264Vac.

48

to 62Hz.

5 Watts maximum.

Maximum:

264Vac,

2A resistive. Minimum:

lOVdc,

100mA.

Channel 1 and 2 as form C, (closing contacts). Channel 3, (Alarm 1)

as form A, (change-over contact).

Maximum: 264Vac IA resistive. Minimum: 80Vac, 50mA.

The leakage current through triac and relay contact suppression

components is less than 2mA at 264Vac, 50Hz.

External over current protection devices are required that match the

wiring of the installation. A minimum of 0.5mm2 or 16awg wire is

recommended. Use independent fuses for the instrument supply and

each relay or triac output. Suitable fuses are 2A type T, (EN 60127

time-lag type).

All input and output connections other than triac and relay are

intended for low level signals less than 42V.

18V at 10mA (Max. current: 20mA).

0 to 20mA (600W max.), 0 to 10V (500W min.).

Contact closure, (non isolated).

EIA-232, or 4-wire EIA-485, (both isolated). ANSI X3.28, subject 2.5

and A4.

00 to 99.

Adjustable as: 300, 600, 1200,

2400,4800,

9600, 19200 Baud.

7 data bits, even parity bit, 1 stop bit.

See Chapter 2.

0.55Kg, (1.21bs) including sieeve and mounting clamps.

12 bit,

(0.7mV)

125ms, corresponds to 8 measurements per second.

>120dB

at

264Vac,

50

/

60Hz.

0.25% of reading,

+l

LSD or

+l

deg C

Internal, >20: 1 rejection of ambient temperature.

External configurable as

45°C or 50°C.

1 OOOR

J, B, E, N, K, L, R, S, PL2 and T.

DIN 43710; DIN IEC 584

l(84);

BS 4937 (73);

ASTM E 230(72)

808/847

&

809/849

installation and Operating Instructions

3-1

Page is loading ...

Eurotherm 808/847 & 809/849 Installation guide

This manual is also suitable for

Eurotherm 808/847 & 809/849 Installation guide

Related papers

Other documents