American Dynamics ADS32X Installation Instructions Manual

Brand: American Dynamics

Model: ADS32X

Category: Motorcycle Accessories

Type: Installation Instructions Manual

ADS32X Touch Tracker

with Video Matrix Switcher

Installation Instructions

8000-1691-02. Rev. A (7 pages)

AD32

Parts Required

Touch Tracker Installation Kit:

Part Number 0351-0474-07

INSTL KIT, TOUCH TRKR, W/RJ45 1

Description Qty Part No.

CABLE ASSY,MDLR,14FT,8 COND,CROSS-P 1 6003-0047-01

SCR,THD CUT,M2.9X9.5,PHP,ST,Z,T1 1 5899-0004-102

ANCHOR,PLASTIC,W/O SCREW,8-10 2 2880-0083-01

SCR,TYP AB,PHP,CAD,#8X1" 2 2816-7634-44

CONN,PLUG,TUBLR,.200CTR,26-12AWG,1X 1 2109-0254-04

LUG,SPADE,CRIMP,INSUL,22-16AWG 3 2141-0002

CABLE,3COND,18AWG,CM 16.5 6002-0024-01

INTERCONNECT BOX,TOUCHTRACKER 1 0300-1000-01

CABLE ASSY,TOUCH TRACKER,INTFC TO Q 1 0650-0932-01

HOOD,D-SUB,9POS,EMI/RFI,.25 DIA CAB 1 2125-0007-02

CONN,D-SUB,PLUG,HSG,9POS,SSI 1 2130-0021-01

FERRITE CORE 1 2700-0023-01

QUICK REFERENCE GUID 1 8000-1674-01

TOUCH TRACHER STRAIN RELIEF INSTR 1 8000-1370-01

Installation Procedures

W A R N I N G

RISK OF ELECTRIC SHOCK!

Disconnect AC Power.

CAUTION—ELECTROSTATIC

SENSITIVE DEVICES!

Follow proper handling procedures to

prevent component failure.

See

Remote Switcher Location

for procedures

when the Video Matrix Switcher will be more than 4m

(14 ft) from the EIMs.

1. Attach each EIM to a wall or other surface within

3m (10 ft) of its Touch Tracker controller.

2. Terminate the EIM that is at the end of the

SensorNet network.

See Figure 1 for the wiring diagram for a typical 2-

controller AD32 system installation. For more

information on the SensorNet network, see the

SensorNet Network Guide

(PN 8000-0970-01).

3. Attach the 3 spade lugs to one end of the 3-

conductor cable, then attach the lugs to the EIM

power transformer.

4. Connect the power transformer cable and the

SensorNet data cable, and if required, the data

cable to EIM #2, to the compression connector,

and connect it to J3 on each EIM.

5. Wire the DB9 connector to the data cable. See

the tables in Figure 1. Assemble the hood onto

the DB9 connector.

6. Install the ferrite core onto the cable assembly,

2.54-3.81cm (1 in.-1.5 in.) from the RJ45

connector (see Figure 2).

7. Connect the data cable to J1 on the EIM to the

RS232 port 1 (primary) or port 2 (secondary) on

the rear panel of the Video Matrix Switcher.

8. Connect a modular cable to J2 on EIM and to the

Touch Tracker controller.

9. Plug each power transformer into a grounded,

3-wire receptacle.

NOTE:

If the keypad and backlighting do not

illuminate when power is applied, unplug the

power transformers, check all wiring connections,

and repeat step 9.

10. Press

on the Touch Tracker keypad to

calibrate the controller.

11. Using the Tracker Ball, page down the screen to

the

Calibration

menu option.

12. Press the zoom button to select the

Calibrate

menu option if it is displayed on the top line of the

LCD window, or press the focus button if it is

displayed on the second line.

13. Perform the Tracker Ball operations displayed in

the LCD window until

Calibration Done

appears in the window.

14. Press

to save the configuration and return

to the Camera Control mode.

15. To configure the Touch Tracker controller as a

primary or secondary unit, page down the screen

to the

Tog Primary/2nd

menu option.

16. To select the

Tog Primary/2nd

menu option,

press the zoom (top line) or focus (bottom line)

button, as appropriate.

17. Press

to toggle between using the Touch

Tracker controller as the primary unit or as the

secondary unit.

18.

Press

to reset the Touch Tracker

controller

as a primary or secondary unit. The controller will

reboot to the Camera Control Mode.

2 INSTALLATION INSTRUCTIONS

ADS32X TOUCH TRACKER with VIDEO MATRIX SWITCHER

8000-1691-02, Rev. A

Figure 1. AD32 Wiring Diagram

21354

J-Box #1

EIM #1

DB9 (M)

RJ45

EIM #2

32 1

1-2 TERMINATED

2-3 UNTERMINATED

321

1-2 TERMINAT ED

2-3 UNTERMINA TE D

5 2 3

21354

J-Box #2

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31

2 4 6 8 10 12 14 16 18 20 22 24 26 28 31 32

1 2 3 4 5 6 7 8 SI NO NC C

1 2 3 4 5

1 2 3

RS232 PORTS

MONITORS

ALARMS

RELAY

120V

60Hz

CAMERAS

RJ45

5 4 2

ASSY

0301-0340-01 REV-

ASSY

0301-0340-01 REV-

UniCard

321

DB9 (M)

5 2 3

RJ45

5 4 2

321

Primary

OUCH

RACKER

Secondary

OUCH

RACKER

Video Matrix Switcher

EIM DB9 (M)

COLOR PIN FUNCTION

Green 3 Receive

Red 2 Transmit

Orange 5 Ground

NOTE:

The system supports up to 2

controllers. Terminate E1 on

the EIM that is on an end point

of the SensorNet network.

NOTE:

The maximum combined SensorNet

cable length is 1219m (4000').

24 Vac B

Ground

UNTERMINATED

EIM Transformers

24 Vac A

24 Vac B

Ground

24 Vac A

RJ45 Wiring

COLOR PIN

Green 5

Red 4

Orange 2

J-Box P8

COLOR PIN Function

Orange 1 Host A

Yellow 2 Host B

Orange 3 Auxiliary A

Yellow 4 Auxiliary B

J-Box P1-P6

COLOR PIN Function

Orange 1 SensorNet A

White 2 28Vac

Red 3 Ground

Black 4 28Vac

Yellow 5 SensorNet B

UniCard P3 Wiring

COLOR PIN FUNCTION

Orange 1 SensorNet A

Yellow 2 SensorNet B

Black 3 24Vac A

Red 4 Ground

White 5 24Vac B

TERMINATED

Ferrite Core

Modular

Cable

Data Cable

120Vac, 60Hz or

240Vac, 50Hz

ADS32X TOUCH TRACKER with VIDEO MATRIX SWITCHER

8000-1691-02, Rev. A

INSTALLATION INSTRUCTIONS 3

Calibrating the Tracker Ball

1. Press

. The

Calibration

menu option

will appear on the first line.

2. Press the zoom (line 1) or focus (line 2) button

to select the

Calibration

menu option.

3. Follow the instructions on the LCD screen.

4. Press

to exit.

If you do not follow each instruction on the screen, the

dome may not function properly. Re-calibrate the

Tracker Ball if the dome does not pan or tilt properly.

Calibration is only for the Touch Tracker controller.

Resetting a Dome

1. Use the number buttons to select the dome to

reset, then press Camera.

2. Press Menu.

3. Using the Tracker Ball, scroll down to

Reset Dome.

4. Press the zoom (line 1) or focus (line 2) button

to select the Reset Dome menu option.

The Touch Tracker will send a request to the selected

dome to reboot.

Switching Primary and

Secondary Functions between

Controller Units

1. Press Menu.

2. Using the Tracker Ball, scroll down to

Tog Primary/2nd.

3. Press the zoom (line 1) or focus (line 2) button

to select the Tog Primary/2nd menu option.

4. Press Next to toggle between using the primary

unit for SensorNet polling and alarm monitoring

or as the secondary unit with limited user

functionality.

5. Press Menu to reset the controller as a primary

or secondary unit.

The controller will reboot and return to the Camera

Control Mode.

Switching Zoom and Focus

Functions between Left and

Right Buttons

1. Press Menu.

2. Using the Tracker Ball, scroll down to

Tog Zoom/Focus.

3. Press the zoom (line 1) or focus (line 2) button

to select the Tog Zoom/Focus menu option.

4. Press Next to switch the Zoom and Focus

functions between the right and left buttons.

5. Press Menu to save the configuration and exit.

Adjusting V-Phase

1. Press Menu.

2. Using the Tracker Ball, scroll down to Adjust V-

Phase.

3. Press the zoom (line 1) or focus (line 2) button

to select the Adjust V-Phase menu option.

4. Press Next or Prev to observe V-Phase through

the oscilloscope or Fluke scope.

5. Press Menu to exit.

Off-line domes or fixed cameras will generate a warning

beep and disallow use of the V-Phase utility. For

additional information on adjusting V-Phase, see the

Service section of the AD32 Installation and Service

Manual.

Figure 2. Ferrite Core Attachment

0 in

2.54 - 3.81 cm

(1" - 1.5")

Ferrite Core

RJ45

DB9(M)

Place 1 loop into core

slot; close core halves;

gently pull cable to

tighten loop.

4 INSTALLATION INSTRUCTIONS

ADS32X TOUCH TRACKER with VIDEO MATRIX SWITCHER

8000-1691-02, Rev. A

Reviewing System Information

1. Press

2. Using the Tracker Ball, scroll down to

System Info

3. Press the zoom (line 1) or focus (line 2) button

to select the

System Info

menu option. The

LCD screen displays the following message:

Primary/Secondary Indicator:

Primary Unit

4. Press

to step through the following

messages:

Flash and EEPROM checksum values:

ROM Checksum

E=0A7B F=9C82

Flash

Checksum

EEPROM

Checksum

Tracker Ball calibration values:

Down

Min 63 60 61 60

Max D3 C3 C6 DE

UpLeft

Right

Flash and EEPROM part numbers (including

version):

Flash Part Number

and Version

Product Code

F 0701-0000-0000

Product Code

E 0701-0000-0000

EEPROM Part Number

and Version

5. Press

to exit.

Performing SensorNet Ping

Test

1. Use the number buttons to select a dome to

test, then press

Camera

2. Press

3. Using the Tracker Ball, scroll down to

Ping Dome/TTR

4. Press the zoom (line 1) or focus (line 2) button

to select the

Ping Dome/TTR

menu option

and to start the ping test on the selected

dome. The LCD screen displays the following

message:

=Device being

tested

No. of pings

transmitted

*Dome Tx=0006

TTR Bad=0002

No. of failed

responses

5. Press Next to perform the ping test on the

Secondary Touch Tracker controller unit.

6. Press

to exit.

Off-line domes or fixed cameras will generate a

warning beep and disallow use of the SensorNet

network test.

Changing the Port Setting

1. Press Menu.

2. Using the Tracker Ball, scroll down to

Port Settings.

3. Press the zoom (line 1) or focus (line 2) button

to select the Port Settings menu option. The

LCD screen displays the following message:

*Operating Mode

Download Mode

=Selected mode

4. Press Next to change the currently selected

mode.

5. Press

to save the change and exit.

ADS32X TOUCH TRACKER with VIDEO MATRIX SWITCHER

8000-1691-02, Rev. A

INSTALLATION INSTRUCTIONS 5

Remote Switcher Location

If the EIM and Touch Trackers will be located more

than 4m (14 ft) but less than 15m (50 ft) from the

Video Matrix Switcher, the following additional

equipment will be needed:

Description Qty Part No.

CABLE ASSY,MDLR,14FT,8 COND,CROSS-P 1 6003-0047-01

TERMINAL, RJ45 2 2113-0019-01

ANCHOR,PLASTIC,W/O SCREW,8-10 4 2880-0083-01

SCR,TYP AB,PHP,CAD,#8X1" 4 2816-7634-44

CABLE,3COND,18AWG,4M-15M (14’-50’) 1 6002-0024-01

WARNING: Shock Hazard!

Disconnect AC Power.

CAUTION: static sensitive

components!

Follow proper handling procedures to

prevent component failure.

Installation Procedures

1. Attach each EIM to a wall or other surface within

3m (10 ft) of its Touch Tracker controller.

2. Terminate the EIM at the end of the SensorNet

network.

See Figure 1 for the wiring diagram for a typical

2-controller AD32 system installation. See Figure

3 for the wiring diagram for remotely located

Video Matrix Switcher. For more information on

the SensorNet network, see the

SensorNet

Network Guide

(PN 8000-0970-01).

3. Attach the HP0047 terminal boxes to a wall. The

remote terminal box must be within 15m (50 ft) of

the EIM terminal box.

4. Connect the 3-wire, 18AWG shielded cable to

the terminal boxes (see Figure 3).

5. Attach the 3 spade lugs to one end of the 3-

conductor cable, then attach the lugs to the EIM

power transformer.

6. Connect the power transformer cable and the

SensorNet data cable, and if required, the data

cable to EIM #2, to the compression connector,

and connect it to J3 on each EIM.

7. Wire the DB9 connector to the data cable. See

the tables on page 2. Assemble the hood onto

the DB9 connector.

8. Connect the data cable to J1 on the EIM to the

HP0047 terminal box.

9. Install a ferrite core onto a modular cable

assembly, 2.54-3.81cm (1 in.-1.5 in.) from an

RJ45 connector (see Figure 2).

10. Connect the modular cable to the remote

HP0047 terminal box and to the RS232 port 1

(primary) or port 2 (secondary) on the rear panel

of the Video Matrix Switcher.

11. Connect a modular cable to J2 on EIM and to the

Touch Tracker controller.

12. Plug each power transformer into a grounded,

3-wire receptacle.

NOTE:

If the keypad and backlighting do not

illuminate when power is applied, unplug the

power transformers, check all wiring

connections, and repeat step 9.

13. Press

on the Touch Tracker keypad to

calibrate the controller.

14. Using the Tracker Ball, page down the screen to

the

Calibration

menu option.

15. Press the zoom button to select the

Calibrate

menu option if it is displayed on the top line of

the LCD window, or press the focus button if it is

displayed on the second line.

16. Perform the Tracker Ball operations displayed in

the LCD window until

Calibration Done

appears in the window.

17. Press

to save the configuration and return

to the Camera Control mode.

18. To configure the Touch Tracker controller as a

primary or secondary unit, page down the screen

to the

Tog Primary/2nd

menu option.

19. To select the

Tog Primary/2nd

menu option,

press the zoom (top line) or focus (bottom line)

button, as appropriate.

20. Press

to toggle between using the Touch

Tracker controller as the primary unit or as the

secondary unit.

21. Press

to reset the Touch Tracker

controller

as a primary or secondary unit. The controller

will reboot to the Camera Control Mode.

6 INSTALLATION INSTRUCTIONS

ADS32X TOUCH TRACKER with VIDEO MATRIX SWITCHER

8000-1691-02, Rev. A

Figure 3. VMS Wiring Diagram—Remote Switcher Location

5 2 3

RJ45

DB9 (M)

24 Vac A

Ground

24 Vac B

5 4 2

RJ45

EIM

5 4 3 2 1

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31

2 4 6 8 10 12 14 16 18 20 22 24 26 28 31 32

1 2 3 4 5 6 7 8 SI NO NC C

1 2 3 4 5

1 2 3

RS232 PORTS

MONITORS

ALARMS

RELAY

120V

60Hz

CAMERAS

Transformer

J3 Wiring

Pin Function

1N/A

2 24Vac A

3 Ground

4 24Vac B

5N/A

DB9 (M) Wiring

Color Pin Function

Green 3 Receive

Red 2 Transmit

Orange 5 Ground

Touch Tracker

RJ45 Wiring

Color Pin

Green 5

Red 4

Orange 2

Video Matrix Switcher

3-wire,

18AWG

Shield

EIM

Terminal

Box

Data

Cable

Modular

Cable

Modular

Cable

Ferrite

Core

Remote

Terminal

Box

120Vac, 60Hz or

240Vac, 50Hz

ADS32X TOUCH TRACKER with VIDEO MATRIX SWITCHER

8000-1691-02, Rev. A

INSTALLATION INSTRUCTIONS 7

Alarm and Relay

Connections

The back panel of the AD32 Video Matrix Switcher

provides eight alarm contact inputs, an external

frequency synchronization input, and contact

terminations for an internal alarm-activated relay.

You can program the Form-C internal relay to

activate during alarms for control of a VCR or other

alarm response device.

Figure 4. Alarm/Relay Connections

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31

2 4 6 8 10 12 14 16 18 20 22 24 26 28 31 32

1 2 3 4 5 6 7 8 SI N O N C C

1 2 3 4 5

1 2 3

RS232 PORTS

MONITORS

ALARMS

RELAY

120V

60Hz

CAMERAS

1 2 3 4 5 6 7 8 SI NO NC C

ALARMS

RELAY

The following is a description of the alarm and

relay connector pins.

Pin Description

1 Ground

2Alarm 1

3Alarm 2

4Alarm 3

5Alarm 4

6Alarm 5

7Alarm 6

8Alarm 7

9Alarm 8

10 Ground

11 External Sync Ground

12 External Sync Input

13 Ground

14 Relay–Normally Open

15 Relay–Normally Closed

16 Relay–Common

Connections

Alarms

•

Alarm contact closures must have a resistance

of 500 Ohms or less.

•

Connect alarm contacts to inputs 1 through 8

(pins 2 through 9).

•

Connect alarm contact returns to Ground (pin

1 or 10).

External Sync

•

External sync input signal must be 1-5Vrms,

50/60Hz.

•

Connect external sync input to

(pin 12).

•

Connect external sync ground to Ground (pin

11).

Relay

•

Connections for the internal relay are normally

open (NO), normally closed (NC), and

common (C). The relay contact ratings are

0.6A @ 120Vac / 0.3A @ 240Vac or 2.0A @

30Vdc.

•

Connect an alarm-response device requiring a

normally open circuit to

(pin 14) and

(pin

16).

•

Connect an alarm-response device requiring a

normally closed circuit to

(pin 15) and

(pin 16).

Pin 16

Video Matrix Switcher—Rear Panel

120Vac, 60Hz or

240Vac, 50Hz

American Dynamics ADS32X Installation Instructions Manual

Brand: American Dynamics

Model: ADS32X

Category: Motorcycle Accessories

Type: Installation Instructions Manual

Download PDF

report

American Dynamics ADS32X Installation Instructions Manual

American Dynamics ADS32X Installation Instructions Manual

Related papers

Other documents