2. Troy-Bilt
  3. 31BM63P3711
31BM63P3711

Troy-Bilt 31BM63P3711 Fast Start Guide

  • Hello! I am an AI chatbot trained to assist you with the Troy-Bilt 31BM63P3711 Fast Start Guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How do I switch the snow thrower into gear?
    How do I install the chute?
    How do I install the control head?
    How do I install the hex rod?
    How do I connect the power cord?
    How do I start the engine?
Hex Rod
Form No. 778-11821B© 2009 31BM63P3
Chute
Handle Knobs
Chute Base
Upper Handle
Chute Support
Bracket
Chute Control
Head
Place shift lever into F6 A.
position.
Pivot upper handle B.
into operating
position
Tighten handle knobs.C.
A
A
B
C
Remove cotter pin, wing nut and A.
hex screw from chute control head.
Remove clevis B.
pin and bow-
tie pin from
chute support
bracket.
B
Squeeze the trigger
on the joystick and rotate
the chute (by hand)
to face forward.
The holes in the rear
of the chute control head
will be facing up.
Shift Lever
Chute Control
Rotate the chute
control to 1 o’clock,
so the silver arrow
on the pinion gear faces
upward.
Insert the round end of the hex rod
(hole pointing upward) as far as
possible into the chute control head.
Secure the round end of the hex
rod to the chute control head with
the cotter pin removed in Step 2.
Secure the chute control head
to the support bracket with the
remaining hardware removed
in Step 2.
Insert the hex end of the rod
(hole pointing upward)
into the pinion gear.
Place chute onto chute
base with the hex rod
positioned beneath the
handle panel.
Reinstall the hex bolt
removed in Step 2 but
do not secure with wing
nut at this time.
1
4
2
5
3
6
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPAÑOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
Oil Fill /
Dipstick
Electric Starter
Button
Electric Starter
Outlet
Primer
Key
Throttle
Control
Choke
Control
Gas Fill
Form No. 778-11821B © 2009 31BM63P3
Move throttle control into
the Fast
position.
Move the choke control
into the Choke
position.
Connect power cord to A.
electric starter outlet.
Plug other end of power B.
cord into a three-prong
120-volt, grounded, AC
receptacle.
Push primer
three times.
Fill fuel tank with clean,
fresh gasoline. Do not fill
above the base of fuel
tank neck.
Check the oil level using
the dipstick. Add oil if
necessary. (Refer to the
Operator’s Manual)
Insert the key into the
key switch until the key
snaps into place.
Do
not turn the key!
To start engine, A.
push the starter
button.
When engine B.
starts, slowly move
choke knob into
the Run position.
Disconnect cord C.
from power
receptacle first and
then from snow
thrower’s outlet.
1
4
2
5
3
6
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPAÑOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
/