Hex Rod
778-11824B© 2010 31BM73Q3
Chute
Handle Knobs
Chute Base
Upper Handle
Chute Support
Bracket
Chute Control
Head
Place shift lever into A.
F6 position.
Pivot upper handle B.
into operating
position
Tighten knobs.C.
A
B
Shift Lever
Chute Control
A
B
C
Remove cotter pin, wing nut and A.
hex screw from chute control head.
Remove clevis B.
pin and bow-tie
pin from chute
support bracket.
Place chute onto chute
base with the hex rod
positioned beneath the
handle panel.
Reinstall the hex bolt
removed in Step 2 but
do not secure with wing
nut at this time.
Insert the round end of the hex rod
(hole pointing upward) as far as
possible into the chute control head.
Squeeze the trigger
on the joystick and rotate
the chute (by hand)
to face forward.
The holes in the rear
of the chute control head
will be facing up.
Rotate the chute
control to 1 o’clock,
so the silver arrow
on the pinion gear faces
upward.
Secure the round end of the hex
rod to the chute control head with
the cotter pin removed in Step 2.
Secure the chute control head
to the support bracket with the
remaining hardware removed
in Step 2.
Insert the hex end of the rod
(hole pointing upward)
into the pinion gear.
1
4
2
5
3
6
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPAÑOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
Oil Fill /
Dipstick
Electric Starter
Button
Electric Starter
Outlet
Primer
Key
Throttle
Control
Choke
Control
Gas Fill
778-11824B© 2010 31BM73Q3
Move throttle control into
the Fast
position.
Move the choke control
into the Choke
position.
Connect power cord to A.
electric starter outlet.
Plug other end of power B.
cord into a three-prong
120-volt, grounded, AC
receptacle.
Push primer
three times.
Fill fuel tank with clean,
fresh gasoline. Do not fill
above the base of fuel
tank neck.
Check the oil level using
the dipstick. Add oil if
necessary. (Refer to the
Operator’s Manual)
Insert the key into the
key switch until the key
snaps into place.
Do
not turn the key!
To start engine, push A.
the starter button.
When engine starts, B.
slowly move choke
knob into the Run
position.
Disconnect cord from C.
power receptacle
first and then from
snow thrower’s
outlet.
7
10
8
11
9
12
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPAÑOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Troy-Bilt 31BM63P3711 Fast Start Guide
-
Troy-Bilt 31AH55Q5711 Fast Start Guide
-
-
-
-
-
-
-
-
Troy-Bilt 31AH64Q4711 Fast Start Guide
Other documents
-
MTD 247883941 Owner's manual
-
Craftsman CMXGBAM1054546 User manual
-
-
MTD 600 SERIES Owner's manual
-
-
Craftsman 247889720 Owner's manual
-
-
-
-