Chute Support
Bracket
Chute Base
Upper Handle
Chute
Control Rod
778-13452B© 2016 31BM73R3
Chute
Chute Control
Head
A
B
Shift Lever
A. Remove cotter pin, wing nut and
hex screw from chute control head.
B. Remove clevis
pin and bow-tie
pin from chute
support bracket.
Insert the round end of the chute control
rod (hole pointing upward) as far
as possible into the chute control head.
Insert the opposite end of the chute
control rod into the coupler below the
handle panel.
Insert the cotter pin removed in Step 2
into the center hole to secure the round
end of the rod to the chute control head.
Secure the chute control head
to the support bracket with the
remaining hardware removed
in Step 2.
Place chute onto chute
base with the chute
control rod positioned
beneath the handle panel.
Reinstall the hex bolt
removed in Step 2 but
do not secure with wing
nut at this time.
B
C
A. Loosen the top two lock nuts securing the upper
and lower handle and remove the two carriage
screws from the lower handle and set aside.
B. Place shift lever into
F6 position.
C. Pivot upper handle
into operating
position.
D. Attach the two
carriage screws and
lock nuts removed
in Step 1. Finish
securing the handle
by tightening the
top two lock nuts loosened
in Step 1.
D
A
1
4
2
5
3
6
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPAÑOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
778-13452B© 2016 31BM73R3
Throttle
Control
Electric Starter
Outlet
Electric Starter
Button
Oil Fill /
Dipstick
Primer
Key
Choke
Control
Gas Fill
Move throttle control into
the Fast
position.
Move the choke control
into the Choke
position.
A. Connect an
extension cord
to the electric
starter outlet.
B. Plug the other
end of the cord
into a three-
prong 120-volt,
grounded, AC
receptacle.
Push primer
three times.
Insert the key
into the key
switch until
the key snaps
into place.
Do not turn
the key!
A. To start engine,
push the starter
button.
B. When engine
starts, slowly move
choke control
into the Run
position.
C. Disconnect cord
from power
receptacle first and
then from snow
thrower’s outlet.
Fill fuel tank with clean,
fresh gasoline. Do not fill
above the base of fuel
tank neck.
Check the oil level using
the dipstick. Add oil if
necessary. (Refer to the
Operator’s Manual)
7
10
8
11
9
12
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPAÑOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
-
1
-
2
Troy-Bilt Storm Tracker 2890 Operating instructions
- Type
- Operating instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Troy-Bilt 31AM56R3711 Fast Start Guide
-
Troy-Bilt 31AH64Q4711 Fast Start Guide
-
-
Troy-Bilt 31BM63P3711 Fast Start Guide
-
-
-
-
-
-
Other documents
-
MTD 247883941 Owner's manual
-
Craftsman CMXGBAM1054546 User manual
-
-
Craftsman 247889720 Owner's manual
-
-
-
-
-
-