Troy-Bilt 31BM63P3711 Fast Start Guide

31BM63P3711
Troy-Bilt
Brand
Troy-Bilt
Model
31BM63P3711
Type
Fast Start Guide

Troy-Bilt 31BM63P3711 is a powerful snow thrower designed to tackle heavy snowfalls with ease. It features a 31-inch clearing width and a 21-inch intake height, allowing you to clear large areas of snow quickly and efficiently. The 6-speed transmission provides optimal control for different snow conditions, while the electric start ensures effortless starting even in freezing temperatures. The chute control allows you to direct the snow up to 20 feet away, and the adjustable skid shoes help protect your surfaces from damage.

Troy-Bilt 31BM63P3711 is a powerful snow thrower designed to tackle heavy snowfalls with ease. It features a 31-inch clearing width and a 21-inch intake height, allowing you to clear large areas of snow quickly and efficiently. The 6-speed transmission provides optimal control for different snow conditions, while the electric start ensures effortless starting even in freezing temperatures. The chute control allows you to direct the snow up to 20 feet away, and the adjustable skid shoes help protect your surfaces from damage.

778-11821E© 2013 31BM63P3
Chute
Handle Knobs
Chute Base
Upper Handle
Chute Support
Bracket
Chute Control
Head
A. Place shift lever into F6
position.
B. Pivot upper handle
into operating
position
C. Tighten handle knobs.
A
A
B
C
A. Remove cotter pin, wing nut and hex
screw from chute control head.
B. Rem ove clev is p in
and bow-tie
pin from
chute support
bracket.
B
Squeeze the trigger
on the chute control
and rotate the chute
(by hand) to face forward.
The holes in the rear
of the chute control head
will be facing up.
Shift Lever
Chute Control
Rotate the chute
control to 1 o’clock,
so the silver arrow
on the pinion gear faces
upward.
Insert the round end of the chute control
rod (hole pointing upward) as far
as possible into the chute control head.
Secure the round end of the rod
to the chute control head with the
cotter pin removed in Step 2.
Secure the chute control head
to the support bracket with the
remaining hardware removed
in Step 2.
Insert the hex end of the rod
(hole pointing upward)
into the pinion gear.
Place chute onto chute
base with the chute
control rod positioned
beneath the handle panel.
Reinstall the hex bolt
removed in Step 2 but
do not secure with wing
nut at this time.
Chute
Control Rod
1
4
2
5
3
6
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPAÑOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
Oil Fill /
Dipstick
Electric Starter
Button
Electric Starter
Outlet
Primer
Key
Throttle
Control
Choke
Control
Gas Fill
778-11821E© 2013 31BM63P3
Move throttle control into
the Fast position.
Move the choke control
into the Choke
position.
A. Connect an extension cord
to the electric starter outlet.
B. Plug the other end of the
cord into a three-prong
120-volt, grounded, AC
receptacle.
Push primer
three times.
Fill fuel tank with clean,
fresh gasoline. Do not fill
above the base of fuel
tank neck.
Check the oil level using
the dipstick. Add oil if
necessary. (Refer to the
Operator’s Manual)
Insert the key into the
key switch until the key
snaps into place.
Do not turn the key!
A. To start engine,
push the starter
button.
B. When engine
starts, slowly move
choke knob into
the Run position.
C. Disconnect cord
from power
receptacle first and
then from snow
thrower’s outlet.
7
10
8
11
9
12
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPAÑOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
  • Page 1 1
  • Page 2 2

Troy-Bilt 31BM63P3711 Fast Start Guide

31BM63P3711
Troy-Bilt
Brand
Troy-Bilt
Model
31BM63P3711
Type
Fast Start Guide

Troy-Bilt 31BM63P3711 is a powerful snow thrower designed to tackle heavy snowfalls with ease. It features a 31-inch clearing width and a 21-inch intake height, allowing you to clear large areas of snow quickly and efficiently. The 6-speed transmission provides optimal control for different snow conditions, while the electric start ensures effortless starting even in freezing temperatures. The chute control allows you to direct the snow up to 20 feet away, and the adjustable skid shoes help protect your surfaces from damage.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents