Panasonic CZRD52CP Operating instructions
- Type
- Operating instructions
2
3 4
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
SETTING CURRENT DAY AND TIME
The current day and time need to be set when you turn on the power for the rst time or after a long time has
elapsed since the power was last turned on.
The current time becomes the standard time for all the Timer operations.
Set the current time and day accurately.
Example: Current Day is Wednesday and Current Time is 8:00
1 Turn on the power supply
OFF
/
ON
2 Press
CLOCK
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
MON
“MON” and “12:00” will be
blinking
3 Select Current Day
Press
UP
or
DOWN
to select current day. (Refer to the above example; select WED)
To con rm the selected day, press
SET
.
4 Select Current Time
Press
UP
or
DOWN
to select current time. (Refer to the above example; select 8:00)
To con rm the selected time, press
SET
.
Note:
- Press
UP
to increase or
DOWN
to decrease (1-minute step) or hold the button to change the time
faster.
- If
UP
or
DOWN
is not pressed for 30 seconds during the day or time setting or if
SET
is pressed, the
setting at that moment is con rmed and setting will end.
WED
Final CLOCK Display
“:” will be blinking
User Manual
Wired Remote Control
F566767
01/13
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
CZ - RD52CP
PRODUCT OVERVIEW PRODUCT OVERVIEW
7
11
14 15 17
19
18
20
2
4
5
3
109
6
8
1
12
13
1
Operation LED
11
Remote Control Reset Button
2
OFF/ON Button
12
OFF Indicator
3
Temperature Setting Button
13
Operation Mode Selection Indicators
4
Operation Mode Button
14
Timer/Clock Setting Display
5
Fan Speed Button
15
Fan Speed Display
6
Air ow Direction Selection Button
16
Air ow Direction Setting Display
7
Quiet/Powerful Operation Button
17
Temperature Setting Display
8
Timer Setting Button Group
18
Quiet Operation Indicator
9
Check Button
19
Powerful Operation Indicator
10
Air Conditioner Reset Button
20
System Error Display
16
OPERATIONS OPERATIONS REMOTE CONTROL PREPARATION REMOTE CONTROL PREPARATION
1 TO TURN ON OR OFF THE UNIT
OFF
/
ON
• Please be aware of the OFF indication on the remote control display to prevent the unit from
starting/stopping improperly.
• For normal operation, OFF indicator shown on remote control display when the unit is turn off.
2 TO SET TEMPERATURE
TEMP
• Selection range: 16°C ~ 30°C.
3 TO SELECT OPERATION MODE
MODE
AUTO mode - For your convenience
• Unit selects operation mode according to temperature setting, outdoor and room temperature.
HEAT mode - To enjoy warm air
• Unit takes a while to warm up.
COOL mode - To enjoy cool air
DRY mode - To dehumidify the environment
• Unit operates at low fan speed to give a gentle cooling operation.
• During soft dry operation, the indoor fan operates at a low fan speed.
• The louvers movement might not align with the remote control display.
4 TO SELECT FAN SPEED (5 options)
FAN SPEED
• For AUTO, the indoor fan speed is automatically adjusted according to the operation mode.
5 TO ADJUST VERTICAL AIRFLOW DIRECTION (5 options)
AIR SWING
• Keeps the room ventilated.
• If AUTO is set, the louvers swing up/down automatically.
• In heat mode, the air blows horizontally for a while, then starts to blow downwards.
6
POWERFUL NORMALQUIET
QUIET/
POWERFUL
QUIET - TO ENJOY QUIET ENVIRONMENT
• This operation reduces air ow noise.
POWERFUL - TO ACHIEVE TEMPERATURE QUICKLY
Panasonic Corporation
Website: http://panasonic.net/
ENGLISH
TABLE OF CONTENTS
Product Overview
Remote Control Preparation
Operations
How to Select the Timer
Daily Timer Setting
Weekly Timer Setting
Troubleshooting
2
3
4
5
6
7~8
8
© Panasonic HA Air-Conditioning (M) Sdn. Bhd. 2008.
Unauthorized copying and distribution is a violation
of law.
F566767-OSTH0901-01_1EN.indd 1 1/13/2009 11:06:31 AM
2
3 4
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
SETTING CURRENT DAY AND TIME
The current day and time need to be set when you turn on the power for the rst time or after a long time has
elapsed since the power was last turned on.
The current time becomes the standard time for all the Timer operations.
Set the current time and day accurately.
Example: Current Day is Wednesday and Current Time is 8:00
1 Turn on the power supply
OFF
/
ON
2 Press
CLOCK
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
MON
“MON” and “12:00” will be
blinking
3 Select Current Day
Press
UP
or
DOWN
to select current day. (Refer to the above example; select WED)
To con rm the selected day, press
SET
.
4 Select Current Time
Press
UP
or
DOWN
to select current time. (Refer to the above example; select 8:00)
To con rm the selected time, press
SET
.
Note:
- Press
UP
to increase or
DOWN
to decrease (1-minute step) or hold the button to change the time
faster.
- If
UP
or
DOWN
is not pressed for 30 seconds during the day or time setting or if
SET
is pressed, the
setting at that moment is con rmed and setting will end.
WED
Final CLOCK Display
“:” will be blinking
User Manual
Wired Remote Control
F566767
01/13
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
CZ - RD52CP
PRODUCT OVERVIEW PRODUCT OVERVIEW
7
11
14 15 17
19
18
20
2
4
5
3
109
6
8
1
12
13
1
Operation LED
11
Remote Control Reset Button
2
OFF/ON Button
12
OFF Indicator
3
Temperature Setting Button
13
Operation Mode Selection Indicators
4
Operation Mode Button
14
Timer/Clock Setting Display
5
Fan Speed Button
15
Fan Speed Display
6
Air ow Direction Selection Button
16
Air ow Direction Setting Display
7
Quiet/Powerful Operation Button
17
Temperature Setting Display
8
Timer Setting Button Group
18
Quiet Operation Indicator
9
Check Button
19
Powerful Operation Indicator
10
Air Conditioner Reset Button
20
System Error Display
16
OPERATIONS OPERATIONS REMOTE CONTROL PREPARATION REMOTE CONTROL PREPARATION
1 TO TURN ON OR OFF THE UNIT
OFF
/
ON
• Please be aware of the OFF indication on the remote control display to prevent the unit from
starting/stopping improperly.
• For normal operation, OFF indicator shown on remote control display when the unit is turn off.
2 TO SET TEMPERATURE
TEMP
• Selection range: 16°C ~ 30°C.
3 TO SELECT OPERATION MODE
MODE
AUTO mode - For your convenience
• Unit selects operation mode according to temperature setting, outdoor and room temperature.
HEAT mode - To enjoy warm air
• Unit takes a while to warm up.
COOL mode - To enjoy cool air
DRY mode - To dehumidify the environment
• Unit operates at low fan speed to give a gentle cooling operation.
• During soft dry operation, the indoor fan operates at a low fan speed.
• The louvers movement might not align with the remote control display.
4 TO SELECT FAN SPEED (5 options)
FAN SPEED
• For AUTO, the indoor fan speed is automatically adjusted according to the operation mode.
5 TO ADJUST VERTICAL AIRFLOW DIRECTION (5 options)
AIR SWING
• Keeps the room ventilated.
• If AUTO is set, the louvers swing up/down automatically.
• In heat mode, the air blows horizontally for a while, then starts to blow downwards.
6
POWERFUL NORMALQUIET
QUIET/
POWERFUL
QUIET - TO ENJOY QUIET ENVIRONMENT
• This operation reduces air ow noise.
POWERFUL - TO ACHIEVE TEMPERATURE QUICKLY
Panasonic Corporation
Website: http://panasonic.net/
ENGLISH
TABLE OF CONTENTS
Product Overview
Remote Control Preparation
Operations
How to Select the Timer
Daily Timer Setting
Weekly Timer Setting
Troubleshooting
2
3
4
5
6
7~8
8
© Panasonic HA Air-Conditioning (M) Sdn. Bhd. 2008.
Unauthorized copying and distribution is a violation
of law.
F566767-OSTH0901-01_1EN.indd 1 1/13/2009 11:06:31 AM
2
3 4
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
SETTING CURRENT DAY AND TIME
The current day and time need to be set when you turn on the power for the rst time or after a long time has
elapsed since the power was last turned on.
The current time becomes the standard time for all the Timer operations.
Set the current time and day accurately.
Example: Current Day is Wednesday and Current Time is 8:00
1 Turn on the power supply
OFF
/
ON
2 Press
CLOCK
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
MON
“MON” and “12:00” will be
blinking
3 Select Current Day
Press
UP
or
DOWN
to select current day. (Refer to the above example; select WED)
To con rm the selected day, press
SET
.
4 Select Current Time
Press
UP
or
DOWN
to select current time. (Refer to the above example; select 8:00)
To con rm the selected time, press
SET
.
Note:
- Press
UP
to increase or
DOWN
to decrease (1-minute step) or hold the button to change the time
faster.
- If
UP
or
DOWN
is not pressed for 30 seconds during the day or time setting or if
SET
is pressed, the
setting at that moment is con rmed and setting will end.
WED
Final CLOCK Display
“:” will be blinking
User Manual
Wired Remote Control
F566767
01/13
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
CZ - RD52CP
PRODUCT OVERVIEW PRODUCT OVERVIEW
7
11
14 15 17
19
18
20
2
4
5
3
109
6
8
1
12
13
1
Operation LED
11
Remote Control Reset Button
2
OFF/ON Button
12
OFF Indicator
3
Temperature Setting Button
13
Operation Mode Selection Indicators
4
Operation Mode Button
14
Timer/Clock Setting Display
5
Fan Speed Button
15
Fan Speed Display
6
Air ow Direction Selection Button
16
Air ow Direction Setting Display
7
Quiet/Powerful Operation Button
17
Temperature Setting Display
8
Timer Setting Button Group
18
Quiet Operation Indicator
9
Check Button
19
Powerful Operation Indicator
10
Air Conditioner Reset Button
20
System Error Display
16
OPERATIONS OPERATIONS REMOTE CONTROL PREPARATION REMOTE CONTROL PREPARATION
1 TO TURN ON OR OFF THE UNIT
OFF
/
ON
• Please be aware of the OFF indication on the remote control display to prevent the unit from
starting/stopping improperly.
• For normal operation, OFF indicator shown on remote control display when the unit is turn off.
2 TO SET TEMPERATURE
TEMP
• Selection range: 16°C ~ 30°C.
3 TO SELECT OPERATION MODE
MODE
AUTO mode - For your convenience
• Unit selects operation mode according to temperature setting, outdoor and room temperature.
HEAT mode - To enjoy warm air
• Unit takes a while to warm up.
COOL mode - To enjoy cool air
DRY mode - To dehumidify the environment
• Unit operates at low fan speed to give a gentle cooling operation.
• During soft dry operation, the indoor fan operates at a low fan speed.
• The louvers movement might not align with the remote control display.
4 TO SELECT FAN SPEED (5 options)
FAN SPEED
• For AUTO, the indoor fan speed is automatically adjusted according to the operation mode.
5 TO ADJUST VERTICAL AIRFLOW DIRECTION (5 options)
AIR SWING
• Keeps the room ventilated.
• If AUTO is set, the louvers swing up/down automatically.
• In heat mode, the air blows horizontally for a while, then starts to blow downwards.
6
POWERFUL NORMALQUIET
QUIET/
POWERFUL
QUIET - TO ENJOY QUIET ENVIRONMENT
• This operation reduces air ow noise.
POWERFUL - TO ACHIEVE TEMPERATURE QUICKLY
Panasonic Corporation
Website: http://panasonic.net/
ENGLISH
TABLE OF CONTENTS
Product Overview
Remote Control Preparation
Operations
How to Select the Timer
Daily Timer Setting
Weekly Timer Setting
Troubleshooting
2
3
4
5
6
7~8
8
© Panasonic HA Air-Conditioning (M) Sdn. Bhd. 2008.
Unauthorized copying and distribution is a violation
of law.
F566767-OSTH0901-01_1EN.indd 1 1/13/2009 11:06:31 AM
2
3 4
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
SETTING CURRENT DAY AND TIME
The current day and time need to be set when you turn on the power for the rst time or after a long time has
elapsed since the power was last turned on.
The current time becomes the standard time for all the Timer operations.
Set the current time and day accurately.
Example: Current Day is Wednesday and Current Time is 8:00
1 Turn on the power supply
OFF
/
ON
2 Press
CLOCK
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
MON
“MON” and “12:00” will be
blinking
3 Select Current Day
Press
UP
or
DOWN
to select current day. (Refer to the above example; select WED)
To con rm the selected day, press
SET
.
4 Select Current Time
Press
UP
or
DOWN
to select current time. (Refer to the above example; select 8:00)
To con rm the selected time, press
SET
.
Note:
- Press
UP
to increase or
DOWN
to decrease (1-minute step) or hold the button to change the time
faster.
- If
UP
or
DOWN
is not pressed for 30 seconds during the day or time setting or if
SET
is pressed, the
setting at that moment is con rmed and setting will end.
WED
Final CLOCK Display
“:” will be blinking
User Manual
Wired Remote Control
F566767
01/13
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
CZ - RD52CP
PRODUCT OVERVIEW PRODUCT OVERVIEW
7
11
14 15 17
19
18
20
2
4
5
3
109
6
8
1
12
13
1
Operation LED
11
Remote Control Reset Button
2
OFF/ON Button
12
OFF Indicator
3
Temperature Setting Button
13
Operation Mode Selection Indicators
4
Operation Mode Button
14
Timer/Clock Setting Display
5
Fan Speed Button
15
Fan Speed Display
6
Air ow Direction Selection Button
16
Air ow Direction Setting Display
7
Quiet/Powerful Operation Button
17
Temperature Setting Display
8
Timer Setting Button Group
18
Quiet Operation Indicator
9
Check Button
19
Powerful Operation Indicator
10
Air Conditioner Reset Button
20
System Error Display
16
OPERATIONS OPERATIONS REMOTE CONTROL PREPARATION REMOTE CONTROL PREPARATION
1 TO TURN ON OR OFF THE UNIT
OFF
/
ON
• Please be aware of the OFF indication on the remote control display to prevent the unit from
starting/stopping improperly.
• For normal operation, OFF indicator shown on remote control display when the unit is turn off.
2 TO SET TEMPERATURE
TEMP
• Selection range: 16°C ~ 30°C.
3 TO SELECT OPERATION MODE
MODE
AUTO mode - For your convenience
• Unit selects operation mode according to temperature setting, outdoor and room temperature.
HEAT mode - To enjoy warm air
• Unit takes a while to warm up.
COOL mode - To enjoy cool air
DRY mode - To dehumidify the environment
• Unit operates at low fan speed to give a gentle cooling operation.
• During soft dry operation, the indoor fan operates at a low fan speed.
• The louvers movement might not align with the remote control display.
4 TO SELECT FAN SPEED (5 options)
FAN SPEED
• For AUTO, the indoor fan speed is automatically adjusted according to the operation mode.
5 TO ADJUST VERTICAL AIRFLOW DIRECTION (5 options)
AIR SWING
• Keeps the room ventilated.
• If AUTO is set, the louvers swing up/down automatically.
• In heat mode, the air blows horizontally for a while, then starts to blow downwards.
6
POWERFUL NORMALQUIET
QUIET/
POWERFUL
QUIET - TO ENJOY QUIET ENVIRONMENT
• This operation reduces air ow noise.
POWERFUL - TO ACHIEVE TEMPERATURE QUICKLY
Panasonic Corporation
Website: http://panasonic.net/
ENGLISH
TABLE OF CONTENTS
Product Overview
Remote Control Preparation
Operations
How to Select the Timer
Daily Timer Setting
Weekly Timer Setting
Troubleshooting
2
3
4
5
6
7~8
8
© Panasonic HA Air-Conditioning (M) Sdn. Bhd. 2008.
Unauthorized copying and distribution is a violation
of law.
F566767-OSTH0901-01_1EN.indd 1 1/13/2009 11:06:31 AM
2
3 4
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
SETTING CURRENT DAY AND TIME
The current day and time need to be set when you turn on the power for the rst time or after a long time has
elapsed since the power was last turned on.
The current time becomes the standard time for all the Timer operations.
Set the current time and day accurately.
Example: Current Day is Wednesday and Current Time is 8:00
1 Turn on the power supply
OFF
/
ON
2 Press
CLOCK
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
MON
“MON” and “12:00” will be
blinking
3 Select Current Day
Press
UP
or
DOWN
to select current day. (Refer to the above example; select WED)
To con rm the selected day, press
SET
.
4 Select Current Time
Press
UP
or
DOWN
to select current time. (Refer to the above example; select 8:00)
To con rm the selected time, press
SET
.
Note:
- Press
UP
to increase or
DOWN
to decrease (1-minute step) or hold the button to change the time
faster.
- If
UP
or
DOWN
is not pressed for 30 seconds during the day or time setting or if
SET
is pressed, the
setting at that moment is con rmed and setting will end.
WED
Final CLOCK Display
“:” will be blinking
User Manual
Wired Remote Control
F566767
01/13
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
CZ - RD52CP
PRODUCT OVERVIEW PRODUCT OVERVIEW
7
11
14 15 17
19
18
20
2
4
5
3
109
6
8
1
12
13
1
Operation LED
11
Remote Control Reset Button
2
OFF/ON Button
12
OFF Indicator
3
Temperature Setting Button
13
Operation Mode Selection Indicators
4
Operation Mode Button
14
Timer/Clock Setting Display
5
Fan Speed Button
15
Fan Speed Display
6
Air ow Direction Selection Button
16
Air ow Direction Setting Display
7
Quiet/Powerful Operation Button
17
Temperature Setting Display
8
Timer Setting Button Group
18
Quiet Operation Indicator
9
Check Button
19
Powerful Operation Indicator
10
Air Conditioner Reset Button
20
System Error Display
16
OPERATIONS OPERATIONS REMOTE CONTROL PREPARATION REMOTE CONTROL PREPARATION
1 TO TURN ON OR OFF THE UNIT
OFF
/
ON
• Please be aware of the OFF indication on the remote control display to prevent the unit from
starting/stopping improperly.
• For normal operation, OFF indicator shown on remote control display when the unit is turn off.
2 TO SET TEMPERATURE
TEMP
• Selection range: 16°C ~ 30°C.
3 TO SELECT OPERATION MODE
MODE
AUTO mode - For your convenience
• Unit selects operation mode according to temperature setting, outdoor and room temperature.
HEAT mode - To enjoy warm air
• Unit takes a while to warm up.
COOL mode - To enjoy cool air
DRY mode - To dehumidify the environment
• Unit operates at low fan speed to give a gentle cooling operation.
• During soft dry operation, the indoor fan operates at a low fan speed.
• The louvers movement might not align with the remote control display.
4 TO SELECT FAN SPEED (5 options)
FAN SPEED
• For AUTO, the indoor fan speed is automatically adjusted according to the operation mode.
5 TO ADJUST VERTICAL AIRFLOW DIRECTION (5 options)
AIR SWING
• Keeps the room ventilated.
• If AUTO is set, the louvers swing up/down automatically.
• In heat mode, the air blows horizontally for a while, then starts to blow downwards.
6
POWERFUL NORMALQUIET
QUIET/
POWERFUL
QUIET - TO ENJOY QUIET ENVIRONMENT
• This operation reduces air ow noise.
POWERFUL - TO ACHIEVE TEMPERATURE QUICKLY
Panasonic Corporation
Website: http://panasonic.net/
ENGLISH
TABLE OF CONTENTS
Product Overview
Remote Control Preparation
Operations
How to Select the Timer
Daily Timer Setting
Weekly Timer Setting
Troubleshooting
2
3
4
5
6
7~8
8
© Panasonic HA Air-Conditioning (M) Sdn. Bhd. 2008.
Unauthorized copying and distribution is a violation
of law.
F566767-OSTH0901-01_1EN.indd 1 1/13/2009 11:06:31 AM
2
3 4
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
SETTING CURRENT DAY AND TIME
The current day and time need to be set when you turn on the power for the rst time or after a long time has
elapsed since the power was last turned on.
The current time becomes the standard time for all the Timer operations.
Set the current time and day accurately.
Example: Current Day is Wednesday and Current Time is 8:00
1 Turn on the power supply
OFF
/
ON
2 Press
CLOCK
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
MON
“MON” and “12:00” will be
blinking
3 Select Current Day
Press
UP
or
DOWN
to select current day. (Refer to the above example; select WED)
To con rm the selected day, press
SET
.
4 Select Current Time
Press
UP
or
DOWN
to select current time. (Refer to the above example; select 8:00)
To con rm the selected time, press
SET
.
Note:
- Press
UP
to increase or
DOWN
to decrease (1-minute step) or hold the button to change the time
faster.
- If
UP
or
DOWN
is not pressed for 30 seconds during the day or time setting or if
SET
is pressed, the
setting at that moment is con rmed and setting will end.
WED
Final CLOCK Display
“:” will be blinking
User Manual
Wired Remote Control
F566767
01/13
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
CZ - RD52CP
PRODUCT OVERVIEW PRODUCT OVERVIEW
7
11
14 15 17
19
18
20
2
4
5
3
109
6
8
1
12
13
1
Operation LED
11
Remote Control Reset Button
2
OFF/ON Button
12
OFF Indicator
3
Temperature Setting Button
13
Operation Mode Selection Indicators
4
Operation Mode Button
14
Timer/Clock Setting Display
5
Fan Speed Button
15
Fan Speed Display
6
Air ow Direction Selection Button
16
Air ow Direction Setting Display
7
Quiet/Powerful Operation Button
17
Temperature Setting Display
8
Timer Setting Button Group
18
Quiet Operation Indicator
9
Check Button
19
Powerful Operation Indicator
10
Air Conditioner Reset Button
20
System Error Display
16
OPERATIONS OPERATIONS REMOTE CONTROL PREPARATION REMOTE CONTROL PREPARATION
1 TO TURN ON OR OFF THE UNIT
OFF
/
ON
• Please be aware of the OFF indication on the remote control display to prevent the unit from
starting/stopping improperly.
• For normal operation, OFF indicator shown on remote control display when the unit is turn off.
2 TO SET TEMPERATURE
TEMP
• Selection range: 16°C ~ 30°C.
3 TO SELECT OPERATION MODE
MODE
AUTO mode - For your convenience
• Unit selects operation mode according to temperature setting, outdoor and room temperature.
HEAT mode - To enjoy warm air
• Unit takes a while to warm up.
COOL mode - To enjoy cool air
DRY mode - To dehumidify the environment
• Unit operates at low fan speed to give a gentle cooling operation.
• During soft dry operation, the indoor fan operates at a low fan speed.
• The louvers movement might not align with the remote control display.
4 TO SELECT FAN SPEED (5 options)
FAN SPEED
• For AUTO, the indoor fan speed is automatically adjusted according to the operation mode.
5 TO ADJUST VERTICAL AIRFLOW DIRECTION (5 options)
AIR SWING
• Keeps the room ventilated.
• If AUTO is set, the louvers swing up/down automatically.
• In heat mode, the air blows horizontally for a while, then starts to blow downwards.
6
POWERFUL NORMALQUIET
QUIET/
POWERFUL
QUIET - TO ENJOY QUIET ENVIRONMENT
• This operation reduces air ow noise.
POWERFUL - TO ACHIEVE TEMPERATURE QUICKLY
Panasonic Corporation
Website: http://panasonic.net/
ENGLISH
TABLE OF CONTENTS
Product Overview
Remote Control Preparation
Operations
How to Select the Timer
Daily Timer Setting
Weekly Timer Setting
Troubleshooting
2
3
4
5
6
7~8
8
© Panasonic HA Air-Conditioning (M) Sdn. Bhd. 2008.
Unauthorized copying and distribution is a violation
of law.
F566767-OSTH0901-01_1EN.indd 1 1/13/2009 11:06:31 AM
2
3 4
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
SETTING CURRENT DAY AND TIME
The current day and time need to be set when you turn on the power for the rst time or after a long time has
elapsed since the power was last turned on.
The current time becomes the standard time for all the Timer operations.
Set the current time and day accurately.
Example: Current Day is Wednesday and Current Time is 8:00
1 Turn on the power supply
OFF
/
ON
2 Press
CLOCK
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
MON
“MON” and “12:00” will be
blinking
3 Select Current Day
Press
UP
or
DOWN
to select current day. (Refer to the above example; select WED)
To con rm the selected day, press
SET
.
4 Select Current Time
Press
UP
or
DOWN
to select current time. (Refer to the above example; select 8:00)
To con rm the selected time, press
SET
.
Note:
- Press
UP
to increase or
DOWN
to decrease (1-minute step) or hold the button to change the time
faster.
- If
UP
or
DOWN
is not pressed for 30 seconds during the day or time setting or if
SET
is pressed, the
setting at that moment is con rmed and setting will end.
WED
Final CLOCK Display
“:” will be blinking
User Manual
Wired Remote Control
F566767
01/13
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
CZ - RD52CP
PRODUCT OVERVIEW PRODUCT OVERVIEW
7
11
14 15 17
19
18
20
2
4
5
3
109
6
8
1
12
13
1
Operation LED
11
Remote Control Reset Button
2
OFF/ON Button
12
OFF Indicator
3
Temperature Setting Button
13
Operation Mode Selection Indicators
4
Operation Mode Button
14
Timer/Clock Setting Display
5
Fan Speed Button
15
Fan Speed Display
6
Air ow Direction Selection Button
16
Air ow Direction Setting Display
7
Quiet/Powerful Operation Button
17
Temperature Setting Display
8
Timer Setting Button Group
18
Quiet Operation Indicator
9
Check Button
19
Powerful Operation Indicator
10
Air Conditioner Reset Button
20
System Error Display
16
OPERATIONS OPERATIONS REMOTE CONTROL PREPARATION REMOTE CONTROL PREPARATION
1 TO TURN ON OR OFF THE UNIT
OFF
/
ON
• Please be aware of the OFF indication on the remote control display to prevent the unit from
starting/stopping improperly.
• For normal operation, OFF indicator shown on remote control display when the unit is turn off.
2 TO SET TEMPERATURE
TEMP
• Selection range: 16°C ~ 30°C.
3 TO SELECT OPERATION MODE
MODE
AUTO mode - For your convenience
• Unit selects operation mode according to temperature setting, outdoor and room temperature.
HEAT mode - To enjoy warm air
• Unit takes a while to warm up.
COOL mode - To enjoy cool air
DRY mode - To dehumidify the environment
• Unit operates at low fan speed to give a gentle cooling operation.
• During soft dry operation, the indoor fan operates at a low fan speed.
• The louvers movement might not align with the remote control display.
4 TO SELECT FAN SPEED (5 options)
FAN SPEED
• For AUTO, the indoor fan speed is automatically adjusted according to the operation mode.
5 TO ADJUST VERTICAL AIRFLOW DIRECTION (5 options)
AIR SWING
• Keeps the room ventilated.
• If AUTO is set, the louvers swing up/down automatically.
• In heat mode, the air blows horizontally for a while, then starts to blow downwards.
6
POWERFUL NORMALQUIET
QUIET/
POWERFUL
QUIET - TO ENJOY QUIET ENVIRONMENT
• This operation reduces air ow noise.
POWERFUL - TO ACHIEVE TEMPERATURE QUICKLY
Panasonic Corporation
Website: http://panasonic.net/
ENGLISH
TABLE OF CONTENTS
Product Overview
Remote Control Preparation
Operations
How to Select the Timer
Daily Timer Setting
Weekly Timer Setting
Troubleshooting
2
3
4
5
6
7~8
8
© Panasonic HA Air-Conditioning (M) Sdn. Bhd. 2008.
Unauthorized copying and distribution is a violation
of law.
F566767-OSTH0901-01_1EN.indd 1 1/13/2009 11:06:31 AM
2
3 4
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
SETTING CURRENT DAY AND TIME
The current day and time need to be set when you turn on the power for the rst time or after a long time has
elapsed since the power was last turned on.
The current time becomes the standard time for all the Timer operations.
Set the current time and day accurately.
Example: Current Day is Wednesday and Current Time is 8:00
1 Turn on the power supply
OFF
/
ON
2 Press
CLOCK
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
MON
“MON” and “12:00” will be
blinking
3 Select Current Day
Press
UP
or
DOWN
to select current day. (Refer to the above example; select WED)
To con rm the selected day, press
SET
.
4 Select Current Time
Press
UP
or
DOWN
to select current time. (Refer to the above example; select 8:00)
To con rm the selected time, press
SET
.
Note:
- Press
UP
to increase or
DOWN
to decrease (1-minute step) or hold the button to change the time
faster.
- If
UP
or
DOWN
is not pressed for 30 seconds during the day or time setting or if
SET
is pressed, the
setting at that moment is con rmed and setting will end.
WED
Final CLOCK Display
“:” will be blinking
User Manual
Wired Remote Control
F566767
01/13
OFF
/
ON
TEMP
TIMER/CLOCK
MODE
QUIET/
POWERFUL
FAN SPEED
MODE
CHECK RESET
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
AC RC
CZ - RD52CP
PRODUCT OVERVIEW PRODUCT OVERVIEW
7
11
14 15 17
19
18
20
2
4
5
3
109
6
8
1
12
13
1
Operation LED
11
Remote Control Reset Button
2
OFF/ON Button
12
OFF Indicator
3
Temperature Setting Button
13
Operation Mode Selection Indicators
4
Operation Mode Button
14
Timer/Clock Setting Display
5
Fan Speed Button
15
Fan Speed Display
6
Air ow Direction Selection Button
16
Air ow Direction Setting Display
7
Quiet/Powerful Operation Button
17
Temperature Setting Display
8
Timer Setting Button Group
18
Quiet Operation Indicator
9
Check Button
19
Powerful Operation Indicator
10
Air Conditioner Reset Button
20
System Error Display
16
OPERATIONS OPERATIONS REMOTE CONTROL PREPARATION REMOTE CONTROL PREPARATION
1 TO TURN ON OR OFF THE UNIT
OFF
/
ON
• Please be aware of the OFF indication on the remote control display to prevent the unit from
starting/stopping improperly.
• For normal operation, OFF indicator shown on remote control display when the unit is turn off.
2 TO SET TEMPERATURE
TEMP
• Selection range: 16°C ~ 30°C.
3 TO SELECT OPERATION MODE
MODE
AUTO mode - For your convenience
• Unit selects operation mode according to temperature setting, outdoor and room temperature.
HEAT mode - To enjoy warm air
• Unit takes a while to warm up.
COOL mode - To enjoy cool air
DRY mode - To dehumidify the environment
• Unit operates at low fan speed to give a gentle cooling operation.
• During soft dry operation, the indoor fan operates at a low fan speed.
• The louvers movement might not align with the remote control display.
4 TO SELECT FAN SPEED (5 options)
FAN SPEED
• For AUTO, the indoor fan speed is automatically adjusted according to the operation mode.
5 TO ADJUST VERTICAL AIRFLOW DIRECTION (5 options)
AIR SWING
• Keeps the room ventilated.
• If AUTO is set, the louvers swing up/down automatically.
• In heat mode, the air blows horizontally for a while, then starts to blow downwards.
6
POWERFUL NORMALQUIET
QUIET/
POWERFUL
QUIET - TO ENJOY QUIET ENVIRONMENT
• This operation reduces air ow noise.
POWERFUL - TO ACHIEVE TEMPERATURE QUICKLY
Panasonic Corporation
Website: http://panasonic.net/
ENGLISH
TABLE OF CONTENTS
Product Overview
Remote Control Preparation
Operations
How to Select the Timer
Daily Timer Setting
Weekly Timer Setting
Troubleshooting
2
3
4
5
6
7~8
8
© Panasonic HA Air-Conditioning (M) Sdn. Bhd. 2008.
Unauthorized copying and distribution is a violation
of law.
F566767-OSTH0901-01_1EN.indd 1 1/13/2009 11:06:31 AM
POSTAVLJANJE TRENUTAČNOG DANA I VREMENA
Kada prvi put uključite uređaj ili kada od zadnjeg uključivanja prođe više vremena, potrebno je postaviti
trenutačni dan i vrijeme.
Trenutačno vrijeme bit će standardno vrijeme za sve radnje mjerača vremena.
Točno postavite trenutačno vrijeme i dan.
Primjer: Trenutačni je dan srijeda, a trenutačno vrijeme 8:00 sati
1 Uključite napajanje
2 Pritisnite
1 UKLJUČIVANJE ILI ISKLJUČIVANJE UREĐAJA
• Pazite na pokazatelj OFF (Isklj.) na zaslonu daljinskog upravljača da biste spriječili nepravilno
pokretanje/zaustavljanje uređaja.
• Tijekom uobičajenog rada, pokazatelj OFF (Isklj.) prikazuje se na zaslonu daljinskog upravljača kada
je uređaj isključen.
2 POSTAVLJANJE TEMPERATURE
• Raspon za odabir: 16 °C ~ 30 °C.
3 ODABIR NAČINA RADA
Način rada AUTO (Automatski) - za jednostavnu uporabu
• Uređaj bira način rada prema postavkama temperature, vanjskoj i sobnoj temperaturi.
Način rada HEAT (Grijanje) - uživanje u toplom zraku
• Uređaju je potrebno određeno vrijeme da se zagrije.
Način rada COOL (Hlađenje) - uživanje u hladnom zraku
Način rada DRY (Sušenje) - odvlaživanje prostorije
• Uređaj radi pri niskoj brzini ventilatora za lagano hlađenje.
• Tijekom radnje blagog sušenja unutarnji ventilator radi pri niskoj brzini.
• Kretnje žaluzine možda neće biti usklađene sa zaslonom daljinskog upravljača.
4 ODABIR BRZINE VENTILATORA (5 opcija)
• U načinu AUTO (Automatski) brzina unutarnjeg ventilatora automatski se podešava prema načinu rada.
5 PODEŠAVANJE OKOMITOG PROTOKA ZRAKA (5 opcija)
• Održava prostoriju prozračenom.
• Ako je postavljen način rada AUTO (Automatski), žaluzine se automatski pomiču gore/dolje.
• U načinu grijanja zrak neko vrijeme puše vodoravno, a zatim počinje puhati prema dolje.
6
TIHI NAČIN RADA - UŽIVANJE U TIHOM OKRUŽENJU
• Ovaj način rada smanjuje buku koju stvara protok zraka.
SNAŽNI NAČIN RADA - BRZO POSTIZANJE TEMPERATURE
3 Odaberite trenutačni dan
Pritisnite ili da biste odabrali trenutačni dan. (Pogledajte prethodni primjer; odaberite WED (Sri))
Da biste potvrdili odabrani dan, pritisnite .
4 Odaberite trenutačno vrijeme
Pritisnite ili da biste odabrali trenutačno vrijeme. (Pogledajte prethodni primjer; odaberite 8:00)
Da biste potvrdili odabrano vrijeme, pritisnite .
Napomena:
- Pritisnite da biste povećali ili smanjili (pomak od 1 min) ili držite gumb da biste brže promijenili
vrijeme.
- Ako 30 sekundi ne pritisnete ili tijekom dana ili kada postavljate vrijeme ili ako pritisnete ,
potvrđuje se postavka odabrana u tom trenutku i postavljanje završava.
Prikaz konačnog SATA
Korisnički priručnik
Žičani daljinski upravljač
HRVATSKI
LED-svjetlo koje označava rad uređaja
Gumb OFF/ON (Isklj./Uklj.)
Gumb za postavljanje temperature
Gumb za odabir načina rada
Gumb brzine ventilatora
Gumb za odabir smjera protoka zraka
Gumb tihog/snažnog načina rada
Skupina gumba za postavljanje mjerača vremena
Gumb provjere
Gumb za vraćanje klimatizacijskog uređaja
na izvorne postavke
Gumb za vraćanje daljinskog upravljača na
izvorne postavke
Pokazatelj OFF (Isključeno)
Pokazatelji odabira načina rada
Prikaz postavki mjerača vremena / sata
Prikaz brzine ventilatora
Prikaz postavke smjera strujanja zraka
Prikaz postavke temperature
Pokazatelj tihog načina rada
Pokazatelj snažnog načina rada
Prikaz pogreške sustava
© Panasonic HA Air-Conditioning (M) Sdn. Bhd.
2008. Neovlaštenim kopiranjem i distribucijom kršite
zakon.
Panasonic Corporation
Web-mjesto: http://panasonic.net/
SADRŽAJ
Pregled proizvoda 2
Priprema daljinskog upravljača 3
Funkcije 4
Odabir mjerača vremena 5
Postavke dnevnog mjerača vremena 6
Postavke tjednog mjerača vremena 7~8
Rješavanje problema 8
PRIPREMA DALJINSKOG UPRAVLJAČA FUNKCIJE
PREGLED PROIZVODA
2
":" će treperiti
Treperit će "MON" (Pon) i
"12:00"
3 4
5 6
7 8
HOW TO SELECT THE TIMER HOW TO SELECT THE TIMER
WEEKLY TIMER SETTING WEEKLY TIMER SETTING
Cancel Current Timer Program
Perform the steps below to cancel the timer program for a particular day.
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
4
2
1
,
3
1. Press
SELECT
to enter day.
2. Press Timer
UP
or
DOWN
until your desired day is shown.
3. Press
SELECT
to enter program setting.
4. Press Timer
UP
or
DOWN
until your desired day is shown.
Press
CANCEL
to cancel the program, will disappear.
For example, if you want to set:
A - Monday to Friday: Unit ON at 09:00 with 20°C (program 1) & unit OFF at 18:30 (program 2).
B - Only Wednesday: Add timer to turn OFF the unit at 12:30 (program 3) and turn ON the unit at 13:30
(program 4).
■
To set A (Monday to Friday – Collective day setting)
To set the time, please refer to steps 1 to 7 of “Day and Timer Set Up Method” on page 7.
Program 1 – select ON, set desired time to 9:00 and desired temperature to 20°C.
Program 2 – select OFF and set desired time to 18:30.
Program 3 ~ 6 – no timer program set, press
MODE
or wait 30 seconds to exit weekly timer.
■
To set B (Wednesday – add new timer program)
1. Press Timer
MODE
to enter timer mode.
2. Press Timer
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until “WED” is selected, press
SELECT
to con rm your selection.
4. Perform steps 4 to 7 of “Day and Timer Set Up Method” to add program 3 and program 4.
Note: Timer that has setting nearest to the current time and day will be activated first.
Disable & Enable Weekly Timer
• To disable weekly timer setting, press
MODE
, then press
CANCEL
.
• To enable previous weekly timer setting, press
MODE
, then press
SET
.
TROUBLESHOOTING TROUBLESHOOTING
The following symptoms occur when abnormality occurs during operation.
• The unit stops and operation LED OFF.
• OFF indicator does not shown on remote control display.
When abnormality occurs, use remote control to retrieve error code.
OFF
/
ON
TIMER/CLOCK
FAN SPEED
MODE
CHECK
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
OFF
Indicator
1
,
3
2
Operation
LED
Ensure the operation LED is in OFF condition.
1. Press for 5 seconds.
2. Press
UP
or
DOWN
. If error code and abnormality can be
identi ed, the operation LED will be ON continuously, then jot
down the error code.
3. Press for 5 seconds to quit checking.
4. Reveal the error code to authorized dealer.
Printed in China
OSTH0901-01
DAILY TIMER SETTING DAILY TIMER SETTING
►How to Set Weekly Timer
- You can set the Timer for each day of the week (Monday to Sunday) with 6 programs per day.
- ON Timer can be set together with your desired temperature and this temperature will be used
continuously.
- Same timer program cannot be set in the same day.
- You may also select collective days with same timer setting.
- Promotes energy saving by allowing you to set up to 6 programs in any given day.
Day and Timer Set Up Method
1. Press Timer
MODE
for 4 seconds to change display to weekly timer.
2. Press Timer
UP
or
DOWN
to select your desired day.
3. Press
SELECT
to con rm your selection.
4. “1” will be blinking, press
SELECT
to set program 1.
5. Press Timer
OFF/ON
to select ON or OFF timer.
6. Press Timer
UP
or
DOWN
to select your desired time.
If you want to set the timer together with your desired temperature, press
TEMP
to select the temperature.
7. Press
SET
to con rm program 1. The selected day will be highlighted with .
• After 2 seconds, the display will move to the next program. Repeat steps 4 to 7 to set programs 2 to 6.
• During timer setup, if no button is pressed within 30 seconds, or if the
SET
button is pressed, the setting at
that moment is con rmed and timer setup is ended.
Check Current Timer Program
Perform the steps below to check the timer program for a particular day.
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is shown, press
SELECT
to con rm your selection.
4. Press Timer
UP
or
DOWN
to check the set programs.
Modify Current Timer Program or Add New Timer Program
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is shown.
4. Perform steps 4 to 7 of “Day and Timer Set Up Method” to modify existing timer program, or add any timer
program.
►How to Set Daily Timer
- You can set ON timer only or OFF timer only or both ON and OFF timer in a day.
1 Change Display
Press Timer
MODE
to change the display to daily timer.
2 Press Timer
OFF/ON
to select ON or OFF timer.
Example: To turn ON the unit at 09:00
Press Timer
OFF/ON
to select ON timer.
Press
UP
or
DOWN
to select the desired time, then press
SET
to con rm the selected time.
Or press
CANCEL
if you do not want any setting for ON Timer.
Example: To turn OFF the unit at 18:30
Press Timer
OFF/ON
to select OFF timer.
Press
UP
or
DOWN
to select the desired time, then press
SET
to con rm the selected time.
Or press
CANCEL
if you do not want any setting for OFF Timer.
Note:
• When ON timer is set, the unit may start early before the actual set time in order to achieve the
desired temperature on time.
• Timer operation is based on the clock set in the remote control and repeats daily once set.
For clock setting, please refer to Remote Control preparation.
• The timer closest to the current time will be activated rst.
• If timer is cancelled manually or due to power failure, you can restore the previous setting by
pressing
SET
.
Final Display of Daily Timer:
TIMER
ON
OFF
TIMER
ON
TIMER
OFF
Only ON Timer is selected.
The unit will automatically
switch ON at 9:00.
Only OFF Timer is selected.
The unit will automatically
switch OFF at 18:30.
Both ON and OFF Timer are
selected.
2 types of Timer mode can be selected on the remote control.
- Daily Timer
- Weekly Timer
- Daily timer and weekly timer could not be set at the same time.
- Select one of these Timers for your convenience.
How to Change the Display
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
Press
- Press once to change the display from CLOCK to Timer or vice-versa.
- Press for more than 4 seconds to change the display from Daily Timer to Weekly Timer or vice-versa.
Daily Timer Display
Lights up if Timer operation is selected
Time to be selected
(10 minutes step)
OFF Timer
To automatically switch “OFF” the unit
ON Timer
To automatically
switch “ON”
the unit
Weekly Timer Display
ON Timer
To automatically switch “ON” the unit
OFF Timer
To automatically switch “OFF” the unit
Time to be selected
(10 minutes step)
Indicates the selected day
6 different programs can be set
in a day (1 ~ 6)
Lights up if Timer operation is selected
Day to be selected
Indicates the next timer operation day
F566767-OSTH0901-01_1EN.indd 2 1/13/2009 11:06:43 AM
5 6
7 8
HOW TO SELECT THE TIMER HOW TO SELECT THE TIMER
WEEKLY TIMER SETTING WEEKLY TIMER SETTING
Cancel Current Timer Program
Perform the steps below to cancel the timer program for a particular day.
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
4
2
1
,
3
1. Press
SELECT
to enter day.
2. Press Timer
UP
or
DOWN
until your desired day is shown.
3. Press
SELECT
to enter program setting.
4. Press Timer
UP
or
DOWN
until your desired day is shown.
Press
CANCEL
to cancel the program, will disappear.
For example, if you want to set:
A - Monday to Friday: Unit ON at 09:00 with 20°C (program 1) & unit OFF at 18:30 (program 2).
B - Only Wednesday: Add timer to turn OFF the unit at 12:30 (program 3) and turn ON the unit at 13:30
(program 4).
■
To set A (Monday to Friday – Collective day setting)
To set the time, please refer to steps 1 to 7 of “Day and Timer Set Up Method” on page 7.
Program 1 – select ON, set desired time to 9:00 and desired temperature to 20°C.
Program 2 – select OFF and set desired time to 18:30.
Program 3 ~ 6 – no timer program set, press
MODE
or wait 30 seconds to exit weekly timer.
■
To set B (Wednesday – add new timer program)
1. Press Timer
MODE
to enter timer mode.
2. Press Timer
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until “WED” is selected, press
SELECT
to con rm your selection.
4. Perform steps 4 to 7 of “Day and Timer Set Up Method” to add program 3 and program 4.
Note: Timer that has setting nearest to the current time and day will be activated first.
Disable & Enable Weekly Timer
• To disable weekly timer setting, press
MODE
, then press
CANCEL
.
• To enable previous weekly timer setting, press
MODE
, then press
SET
.
TROUBLESHOOTING TROUBLESHOOTING
The following symptoms occur when abnormality occurs during operation.
• The unit stops and operation LED OFF.
• OFF indicator does not shown on remote control display.
When abnormality occurs, use remote control to retrieve error code.
OFF
/
ON
TIMER/CLOCK
FAN SPEED
MODE
CHECK
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
OFF
Indicator
1
,
3
2
Operation
LED
Ensure the operation LED is in OFF condition.
1. Press for 5 seconds.
2. Press
UP
or
DOWN
. If error code and abnormality can be
identi ed, the operation LED will be ON continuously, then jot
down the error code.
3. Press for 5 seconds to quit checking.
4. Reveal the error code to authorized dealer.
Printed in China
OSTH0901-01
DAILY TIMER SETTING DAILY TIMER SETTING
►How to Set Weekly Timer
- You can set the Timer for each day of the week (Monday to Sunday) with 6 programs per day.
- ON Timer can be set together with your desired temperature and this temperature will be used
continuously.
- Same timer program cannot be set in the same day.
- You may also select collective days with same timer setting.
- Promotes energy saving by allowing you to set up to 6 programs in any given day.
Day and Timer Set Up Method
1. Press Timer
MODE
for 4 seconds to change display to weekly timer.
2. Press Timer
UP
or
DOWN
to select your desired day.
3. Press
SELECT
to con rm your selection.
4. “1” will be blinking, press
SELECT
to set program 1.
5. Press Timer
OFF/ON
to select ON or OFF timer.
6. Press Timer
UP
or
DOWN
to select your desired time.
If you want to set the timer together with your desired temperature, press
TEMP
to select the temperature.
7. Press
SET
to con rm program 1. The selected day will be highlighted with .
• After 2 seconds, the display will move to the next program. Repeat steps 4 to 7 to set programs 2 to 6.
• During timer setup, if no button is pressed within 30 seconds, or if the
SET
button is pressed, the setting at
that moment is con rmed and timer setup is ended.
Check Current Timer Program
Perform the steps below to check the timer program for a particular day.
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is shown, press
SELECT
to con rm your selection.
4. Press Timer
UP
or
DOWN
to check the set programs.
Modify Current Timer Program or Add New Timer Program
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is shown.
4. Perform steps 4 to 7 of “Day and Timer Set Up Method” to modify existing timer program, or add any timer
program.
►How to Set Daily Timer
- You can set ON timer only or OFF timer only or both ON and OFF timer in a day.
1 Change Display
Press Timer
MODE
to change the display to daily timer.
2 Press Timer
OFF/ON
to select ON or OFF timer.
Example: To turn ON the unit at 09:00
Press Timer
OFF/ON
to select ON timer.
Press
UP
or
DOWN
to select the desired time, then press
SET
to con rm the selected time.
Or press
CANCEL
if you do not want any setting for ON Timer.
Example: To turn OFF the unit at 18:30
Press Timer
OFF/ON
to select OFF timer.
Press
UP
or
DOWN
to select the desired time, then press
SET
to con rm the selected time.
Or press
CANCEL
if you do not want any setting for OFF Timer.
Note:
• When ON timer is set, the unit may start early before the actual set time in order to achieve the
desired temperature on time.
• Timer operation is based on the clock set in the remote control and repeats daily once set.
For clock setting, please refer to Remote Control preparation.
• The timer closest to the current time will be activated rst.
• If timer is cancelled manually or due to power failure, you can restore the previous setting by
pressing
SET
.
Final Display of Daily Timer:
TIMER
ON
OFF
TIMER
ON
TIMER
OFF
Only ON Timer is selected.
The unit will automatically
switch ON at 9:00.
Only OFF Timer is selected.
The unit will automatically
switch OFF at 18:30.
Both ON and OFF Timer are
selected.
2 types of Timer mode can be selected on the remote control.
- Daily Timer
- Weekly Timer
- Daily timer and weekly timer could not be set at the same time.
- Select one of these Timers for your convenience.
How to Change the Display
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
Press
- Press once to change the display from CLOCK to Timer or vice-versa.
- Press for more than 4 seconds to change the display from Daily Timer to Weekly Timer or vice-versa.
Daily Timer Display
Lights up if Timer operation is selected
Time to be selected
(10 minutes step)
OFF Timer
To automatically switch “OFF” the unit
ON Timer
To automatically
switch “ON”
the unit
Weekly Timer Display
ON Timer
To automatically switch “ON” the unit
OFF Timer
To automatically switch “OFF” the unit
Time to be selected
(10 minutes step)
Indicates the selected day
6 different programs can be set
in a day (1 ~ 6)
Lights up if Timer operation is selected
Day to be selected
Indicates the next timer operation day
F566767-OSTH0901-01_1EN.indd 2 1/13/2009 11:06:43 AM
5 6
7 8
HOW TO SELECT THE TIMER HOW TO SELECT THE TIMER
WEEKLY TIMER SETTING WEEKLY TIMER SETTING
Cancel Current Timer Program
Perform the steps below to cancel the timer program for a particular day.
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
4
2
1
,
3
1. Press
SELECT
to enter day.
2. Press Timer
UP
or
DOWN
until your desired day is shown.
3. Press
SELECT
to enter program setting.
4. Press Timer
UP
or
DOWN
until your desired day is shown.
Press
CANCEL
to cancel the program, will disappear.
For example, if you want to set:
A - Monday to Friday: Unit ON at 09:00 with 20°C (program 1) & unit OFF at 18:30 (program 2).
B - Only Wednesday: Add timer to turn OFF the unit at 12:30 (program 3) and turn ON the unit at 13:30
(program 4).
■
To set A (Monday to Friday – Collective day setting)
To set the time, please refer to steps 1 to 7 of “Day and Timer Set Up Method” on page 7.
Program 1 – select ON, set desired time to 9:00 and desired temperature to 20°C.
Program 2 – select OFF and set desired time to 18:30.
Program 3 ~ 6 – no timer program set, press
MODE
or wait 30 seconds to exit weekly timer.
■
To set B (Wednesday – add new timer program)
1. Press Timer
MODE
to enter timer mode.
2. Press Timer
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until “WED” is selected, press
SELECT
to con rm your selection.
4. Perform steps 4 to 7 of “Day and Timer Set Up Method” to add program 3 and program 4.
Note: Timer that has setting nearest to the current time and day will be activated first.
Disable & Enable Weekly Timer
• To disable weekly timer setting, press
MODE
, then press
CANCEL
.
• To enable previous weekly timer setting, press
MODE
, then press
SET
.
TROUBLESHOOTING TROUBLESHOOTING
The following symptoms occur when abnormality occurs during operation.
• The unit stops and operation LED OFF.
• OFF indicator does not shown on remote control display.
When abnormality occurs, use remote control to retrieve error code.
OFF
/
ON
TIMER/CLOCK
FAN SPEED
MODE
CHECK
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
OFF
Indicator
1
,
3
2
Operation
LED
Ensure the operation LED is in OFF condition.
1. Press for 5 seconds.
2. Press
UP
or
DOWN
. If error code and abnormality can be
identi ed, the operation LED will be ON continuously, then jot
down the error code.
3. Press for 5 seconds to quit checking.
4. Reveal the error code to authorized dealer.
Printed in China
OSTH0901-01
DAILY TIMER SETTING DAILY TIMER SETTING
►How to Set Weekly Timer
- You can set the Timer for each day of the week (Monday to Sunday) with 6 programs per day.
- ON Timer can be set together with your desired temperature and this temperature will be used
continuously.
- Same timer program cannot be set in the same day.
- You may also select collective days with same timer setting.
- Promotes energy saving by allowing you to set up to 6 programs in any given day.
Day and Timer Set Up Method
1. Press Timer
MODE
for 4 seconds to change display to weekly timer.
2. Press Timer
UP
or
DOWN
to select your desired day.
3. Press
SELECT
to con rm your selection.
4. “1” will be blinking, press
SELECT
to set program 1.
5. Press Timer
OFF/ON
to select ON or OFF timer.
6. Press Timer
UP
or
DOWN
to select your desired time.
If you want to set the timer together with your desired temperature, press
TEMP
to select the temperature.
7. Press
SET
to con rm program 1. The selected day will be highlighted with .
• After 2 seconds, the display will move to the next program. Repeat steps 4 to 7 to set programs 2 to 6.
• During timer setup, if no button is pressed within 30 seconds, or if the
SET
button is pressed, the setting at
that moment is con rmed and timer setup is ended.
Check Current Timer Program
Perform the steps below to check the timer program for a particular day.
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is shown, press
SELECT
to con rm your selection.
4. Press Timer
UP
or
DOWN
to check the set programs.
Modify Current Timer Program or Add New Timer Program
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is shown.
4. Perform steps 4 to 7 of “Day and Timer Set Up Method” to modify existing timer program, or add any timer
program.
►How to Set Daily Timer
- You can set ON timer only or OFF timer only or both ON and OFF timer in a day.
1 Change Display
Press Timer
MODE
to change the display to daily timer.
2 Press Timer
OFF/ON
to select ON or OFF timer.
Example: To turn ON the unit at 09:00
Press Timer
OFF/ON
to select ON timer.
Press
UP
or
DOWN
to select the desired time, then press
SET
to con rm the selected time.
Or press
CANCEL
if you do not want any setting for ON Timer.
Example: To turn OFF the unit at 18:30
Press Timer
OFF/ON
to select OFF timer.
Press
UP
or
DOWN
to select the desired time, then press
SET
to con rm the selected time.
Or press
CANCEL
if you do not want any setting for OFF Timer.
Note:
• When ON timer is set, the unit may start early before the actual set time in order to achieve the
desired temperature on time.
• Timer operation is based on the clock set in the remote control and repeats daily once set.
For clock setting, please refer to Remote Control preparation.
• The timer closest to the current time will be activated rst.
• If timer is cancelled manually or due to power failure, you can restore the previous setting by
pressing
SET
.
Final Display of Daily Timer:
TIMER
ON
OFF
TIMER
ON
TIMER
OFF
Only ON Timer is selected.
The unit will automatically
switch ON at 9:00.
Only OFF Timer is selected.
The unit will automatically
switch OFF at 18:30.
Both ON and OFF Timer are
selected.
2 types of Timer mode can be selected on the remote control.
- Daily Timer
- Weekly Timer
- Daily timer and weekly timer could not be set at the same time.
- Select one of these Timers for your convenience.
How to Change the Display
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
Press
- Press once to change the display from CLOCK to Timer or vice-versa.
- Press for more than 4 seconds to change the display from Daily Timer to Weekly Timer or vice-versa.
Daily Timer Display
Lights up if Timer operation is selected
Time to be selected
(10 minutes step)
OFF Timer
To automatically switch “OFF” the unit
ON Timer
To automatically
switch “ON”
the unit
Weekly Timer Display
ON Timer
To automatically switch “ON” the unit
OFF Timer
To automatically switch “OFF” the unit
Time to be selected
(10 minutes step)
Indicates the selected day
6 different programs can be set
in a day (1 ~ 6)
Lights up if Timer operation is selected
Day to be selected
Indicates the next timer operation day
F566767-OSTH0901-01_1EN.indd 2 1/13/2009 11:06:43 AM
5 6
7 8
HOW TO SELECT THE TIMER HOW TO SELECT THE TIMER
WEEKLY TIMER SETTING WEEKLY TIMER SETTING
Cancel Current Timer Program
Perform the steps below to cancel the timer program for a particular day.
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
4
2
1
,
3
1. Press
SELECT
to enter day.
2. Press Timer
UP
or
DOWN
until your desired day is shown.
3. Press
SELECT
to enter program setting.
4. Press Timer
UP
or
DOWN
until your desired day is shown.
Press
CANCEL
to cancel the program, will disappear.
For example, if you want to set:
A - Monday to Friday: Unit ON at 09:00 with 20°C (program 1) & unit OFF at 18:30 (program 2).
B - Only Wednesday: Add timer to turn OFF the unit at 12:30 (program 3) and turn ON the unit at 13:30
(program 4).
■
To set A (Monday to Friday – Collective day setting)
To set the time, please refer to steps 1 to 7 of “Day and Timer Set Up Method” on page 7.
Program 1 – select ON, set desired time to 9:00 and desired temperature to 20°C.
Program 2 – select OFF and set desired time to 18:30.
Program 3 ~ 6 – no timer program set, press
MODE
or wait 30 seconds to exit weekly timer.
■
To set B (Wednesday – add new timer program)
1. Press Timer
MODE
to enter timer mode.
2. Press Timer
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until “WED” is selected, press
SELECT
to con rm your selection.
4. Perform steps 4 to 7 of “Day and Timer Set Up Method” to add program 3 and program 4.
Note: Timer that has setting nearest to the current time and day will be activated first.
Disable & Enable Weekly Timer
• To disable weekly timer setting, press
MODE
, then press
CANCEL
.
• To enable previous weekly timer setting, press
MODE
, then press
SET
.
TROUBLESHOOTING TROUBLESHOOTING
The following symptoms occur when abnormality occurs during operation.
• The unit stops and operation LED OFF.
• OFF indicator does not shown on remote control display.
When abnormality occurs, use remote control to retrieve error code.
OFF
/
ON
TIMER/CLOCK
FAN SPEED
MODE
CHECK
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
OFF
Indicator
1
,
3
2
Operation
LED
Ensure the operation LED is in OFF condition.
1. Press for 5 seconds.
2. Press
UP
or
DOWN
. If error code and abnormality can be
identi ed, the operation LED will be ON continuously, then jot
down the error code.
3. Press for 5 seconds to quit checking.
4. Reveal the error code to authorized dealer.
Printed in China
OSTH0901-01
DAILY TIMER SETTING DAILY TIMER SETTING
►How to Set Weekly Timer
- You can set the Timer for each day of the week (Monday to Sunday) with 6 programs per day.
- ON Timer can be set together with your desired temperature and this temperature will be used
continuously.
- Same timer program cannot be set in the same day.
- You may also select collective days with same timer setting.
- Promotes energy saving by allowing you to set up to 6 programs in any given day.
Day and Timer Set Up Method
1. Press Timer
MODE
for 4 seconds to change display to weekly timer.
2. Press Timer
UP
or
DOWN
to select your desired day.
3. Press
SELECT
to con rm your selection.
4. “1” will be blinking, press
SELECT
to set program 1.
5. Press Timer
OFF/ON
to select ON or OFF timer.
6. Press Timer
UP
or
DOWN
to select your desired time.
If you want to set the timer together with your desired temperature, press
TEMP
to select the temperature.
7. Press
SET
to con rm program 1. The selected day will be highlighted with .
• After 2 seconds, the display will move to the next program. Repeat steps 4 to 7 to set programs 2 to 6.
• During timer setup, if no button is pressed within 30 seconds, or if the
SET
button is pressed, the setting at
that moment is con rmed and timer setup is ended.
Check Current Timer Program
Perform the steps below to check the timer program for a particular day.
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is shown, press
SELECT
to con rm your selection.
4. Press Timer
UP
or
DOWN
to check the set programs.
Modify Current Timer Program or Add New Timer Program
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is shown.
4. Perform steps 4 to 7 of “Day and Timer Set Up Method” to modify existing timer program, or add any timer
program.
►How to Set Daily Timer
- You can set ON timer only or OFF timer only or both ON and OFF timer in a day.
1 Change Display
Press Timer
MODE
to change the display to daily timer.
2 Press Timer
OFF/ON
to select ON or OFF timer.
Example: To turn ON the unit at 09:00
Press Timer
OFF/ON
to select ON timer.
Press
UP
or
DOWN
to select the desired time, then press
SET
to con rm the selected time.
Or press
CANCEL
if you do not want any setting for ON Timer.
Example: To turn OFF the unit at 18:30
Press Timer
OFF/ON
to select OFF timer.
Press
UP
or
DOWN
to select the desired time, then press
SET
to con rm the selected time.
Or press
CANCEL
if you do not want any setting for OFF Timer.
Note:
• When ON timer is set, the unit may start early before the actual set time in order to achieve the
desired temperature on time.
• Timer operation is based on the clock set in the remote control and repeats daily once set.
For clock setting, please refer to Remote Control preparation.
• The timer closest to the current time will be activated rst.
• If timer is cancelled manually or due to power failure, you can restore the previous setting by
pressing
SET
.
Final Display of Daily Timer:
TIMER
ON
OFF
TIMER
ON
TIMER
OFF
Only ON Timer is selected.
The unit will automatically
switch ON at 9:00.
Only OFF Timer is selected.
The unit will automatically
switch OFF at 18:30.
Both ON and OFF Timer are
selected.
2 types of Timer mode can be selected on the remote control.
- Daily Timer
- Weekly Timer
- Daily timer and weekly timer could not be set at the same time.
- Select one of these Timers for your convenience.
How to Change the Display
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
Press
- Press once to change the display from CLOCK to Timer or vice-versa.
- Press for more than 4 seconds to change the display from Daily Timer to Weekly Timer or vice-versa.
Daily Timer Display
Lights up if Timer operation is selected
Time to be selected
(10 minutes step)
OFF Timer
To automatically switch “OFF” the unit
ON Timer
To automatically
switch “ON”
the unit
Weekly Timer Display
ON Timer
To automatically switch “ON” the unit
OFF Timer
To automatically switch “OFF” the unit
Time to be selected
(10 minutes step)
Indicates the selected day
6 different programs can be set
in a day (1 ~ 6)
Lights up if Timer operation is selected
Day to be selected
Indicates the next timer operation day
F566767-OSTH0901-01_1EN.indd 2 1/13/2009 11:06:43 AM
Vrijeme uključivanja mjerača (ON)
Automatsko uključivanje uređaja
Odabir dana
►Postavljanje tjednog mjerača vremena
- Moguće je postaviti mjerač vremena za svaki dan u tjednu (od ponedjeljka do nedjelje) sa 6 programa po danu.
- Vrijeme uključivanja mjerača (ON) može se postaviti zajedno sa željenom temperaturom i ta će se
temperatura neprestano upotrebljavati.
- Isti program mjerača vremena nije moguće postaviti za isti dan.
- Možete i odabrati veći broj dana s istom postavkom mjerača vremena.
- Omogućuje uštedu energije tako što omogućuje postavljanje do 6 programa u svakom danu.
Metoda postavljanja dana i mjerača vremena
1. Pritisnite i držite mjerač vremena 4 sekunde da biste promijenili prikaz na tjedni mjerač vremena.
2. Pritisnite mjerač vremena ili da biste odabrali željeni dan.
3. Pritisnite da biste potvrdili svoj odabir.
4. Treperi "1", pritisnite da biste postavili program 1.
5. Pritisnite mjerač vremena da biste odabrali vrijeme uključivanja mjerača (ON) ili vrijeme
isključivanja mjerača (OFF).
6. Pritisnite mjerač vremena ili da biste odabrali željeno vrijeme.
Želite li postaviti mjerač vremena zajedno sa željenom temperaturom, pritisnite da biste odabrali
temperaturu.
7. Pritisnite da biste potvrdili program 1. Odabrani dan bit će označen s
▼
.
• Nakon što prođu dvije sekunde, prikaz će prijeći na sljedeći program. Ponovite korake 4. do 7. da biste
postavili programe 2 do 6.
• Ako ne pritisnete niti jedan gumb 30 sekundi ili ako pritisnete gumb tijekom postavljanja mjerača
vremena, potvrđuje se postavka odabrana u tom trenutku i završava se postavljanje mjerača vremena.
Provjera trenutačnog programa mjerača vremena
Izvršite sljedeće korake da biste provjerili program mjerača vremena za određeni dan.
1. Pritisnite mjerač vremena da biste unijeli način rada mjerača vremena.
2. Pritisnite da biste unijeli postavku dana.
3. Pritišćite mjerač vremena ili dok se ne prikaže željeni dan, a zatim pritisnite da biste potvrdili odabir.
4. Pritisnite mjerač vremena ili da biste provjerili postavljene programe.
Promjena trenutačnog programa mjerača vremena ili dodavanje novog programa mjerača vremena
1. Pritisnite mjerač vremena da biste unijeli način rada mjerača vremena.
2. Pritisnite da biste unijeli postavku dana.
3. Pritišćite mjerač vremena ili dok se ne prikaže željeni dan.
4. Izvršite korake 4. do 7. iz dijela "Metoda postavljanja dana i mjerača vremena" da biste promijenili postojeći
program mjerača vremena ili dodali program mjerača vremena.
Poništavanje trenutačnog programa mjerača vremena
Izvršite sljedeće korake da biste poništili program mjerača za određeni dan.
1. Pritisnite da biste unijeli dan.
2. Pritišćite mjerač vremena ili dok se ne prikaže željeni dan.
3. Pritisnite da biste unijeli programsku postavku.
4. Pritišćite mjerač vremena ili dok se ne prikaže željeni dan.
Pritisnite da biste poništili program,
▼
će nestati.
Na primjer, želite li postaviti:
A - od ponedjeljka do petka: Uključivanje uređaja u 9:00 sati na 20 °C (program 1) i isključivanje uređaja u
18:30 sati (program 2).
B - samo srijeda: Dodajte mjerač vremena za isključivanje uređaja u 12:30 (program 3) i za uključivanje uređaja
u 13:30 (program 4).
■
Da biste postavili A (od ponedjeljka do petka – kolektivna postavka dana)
Da biste postavili vrijeme, proučite korake od 1. do 7. iz dijela "Metoda postavljanja dana i mjerača vremena" na 7. stranici.
Program 1 – odaberite ON (Uklj.), postavite željeno vrijeme na 9:00 i željenu temperaturu na 20 °C.
Program 2 – odaberite OFF (Isklj.) i postavite željeno vrijeme na 18:30.
Program 3 ~ 6 – nije postavljen program mjerača vremena, pritisnite ili pričekajte 30 sekundi za
izlazak iz tjednog mjerača vremena.
■
Da biste postavili B (srijeda – dodajte novi program mjerača)
1. Pritisnite mjerač vremena da biste unijeli način rada mjerača vremena.
2. Pritisnite mjerač vremena da biste unijeli postavku dana.
3. Pritišćite mjerač vremena ili dok ne odaberete "WED" (Sri), pritisnite da biste potvrdili svoj odabir.
4. Izvedite korake od 4. do 7. iz dijela "Metoda postavljanja dana i mjerača vremena" da biste dodali programe 3 i 4.
Napomena: Prvi će se aktivirati mjerač vremena čije su postavke najbliže trenutačnom vremenu i danu.
Isključivanje i uključivanje tjednog mjerača vremena
• Da biste isključili postavku tjednog mjerača vremena, pritisnite , zatim pritisnite .
• Da biste uključili prethodnu postavku tjednog mjerača vremena, pritisnite , zatim pritisnite .
Sljedeće se situacije događaju kada dođe do nepravilnosti tijekom rada.
• Uređaj se zaustavlja i LED-svjetlo koje označava rad uređaja isključeno je.
• Pokazatelj OFF (Isklj.) ne prikazuje se na zaslonu daljinskog upravljača.
Kada dođe do nepravilnosti, preuzmite kod pogreške s pomoću daljinskog upravljača.
Provjerite je li LED-svjetlo koje označava rad uređaja isključeno.
1. Pritisnite i držite 5 sekundi.
2. Pritisnite ili . Ako se kod pogreške i nepravilnost mogu
utvrditi, LED-svjetlo koje označava rad uređaja neprestano će
svijetliti te tada zapišite kod pogreške.
3. Pritisnite i držite 5 sekundi da biste prekinuli provjeru.
4. Pokažite kod pogreške ovlaštenom dobavljaču.
OSTH0901-01
Na daljinskom se upravljaču mogu odabrati 2 načina rada mjerača vremena.
- Dnevni mjerač vremena
- Tjedni mjerač vremena
- Dnevni mjerač vremena i tjedni mjerač vremena ne mogu se postaviti istovremeno.
- Odaberite jedan od tih mjerača, ovisno o vašim potrebama.
Promjena prikaza
Pritisnite
- Pritisnite jednom da biste promijenili prikaz iz CLOCK (Sat) u mjerač vremena i obrnuto.
- Držite pritisnutim duže od 4 sekunde da biste promijenili prikaz iz dnevnog mjerača vremena u tjedni i obrnuto.
Prikaz dnevnog mjerača vremena
Zasvijetli kada odaberete funkciju Timer (Mjerač vremena)
Vrijeme koje je
potrebno odabrati
(pomak od 10 minuta)
Vrijeme isključivanja mjerača (OFF)
Automatsko isključivanje uređaja
►Postavljanje dnevnog mjerača vremena
- Tijekom jednog dana možete postaviti samo vrijeme uključivanja mjerača (ON), samo vrijeme
isključivanja mjerača (OFF) ili oboje.
1 Promijenite prikaz
Da biste prikaz promijenili na dnevni mjerač vremena, pritisnite mjerač vremena .
2 Pritisnite mjerač vremena da biste odabrali vrijeme uključivanja
mjerača (ON) ili vrijeme isključivanja mjerača (OFF).
Primjer: Za uključivanje uređaja (ON) u 9:00 sati
Pritisnite mjerač vremena da biste odabrali vrijeme uključivanja mjerača (ON).
Pritisnite ili da biste odabrali željeno vrijeme, a zatim pritisnite da biste potvrdili odabrano
vrijeme.
Ili pritisnite ako ne želite izvršiti nikakva postavljanja za vrijeme uključivanja mjerača (ON).
Primjer: Za isključivanje uređaja (OFF) u 18:30 sati
Pritisnite mjerač vremena da biste odabrali vrijeme isključivanja mjerača (OFF).
Pritisnite ili da biste odabrali željeno vrijeme, a zatim pritisnite da biste potvrdili odabrano
vrijeme.
Ili pritisnite ako ne želite izvršiti nikakva postavljanja za vrijeme isključivanja mjerača (OFF).
Napomena:
• Kada je postavljeno vrijeme uključivanja mjerača (ON), uređaj bi se mogao uključiti prije stvarno
postavljenog vremena kako bi postigao željenu temperaturu na vrijeme.
• Rad mjerača vremena temelji se na postavkama sata u daljinskom upravljaču i nakon što je postavljen
svakodnevno se ponavlja. Detalje o postavljanju sata potražite u dijelu Priprema daljinskog upravljača.
• Najprije će se aktivirati mjerač vremena najbliži trenutačnom vremenu.
• Ako ručno poništite mjerač vremena ili se to dogodi zbog nestanka struje, možete vratiti prethodne
postavke pritiskom na .
Konačni prikaz dnevnog mjerača vremena:
Odabrano je samo vrijeme
uključivanja mjerača (ON).
Uređaj se automatski
uključuje u 9:00 sati.
Odabrano je samo vrijeme
isključivanja mjerača (OFF).
Uređaj se automatski
isključuje u 18:30.
Odabrano je i vrijeme
uključivanja (ON) i vrijeme
isključivanja mjerača (OFF).
Vrijeme uključivanja
mjerača (ON)
Automatsko
uključivanje uređaja
Prikaz tjednog mjerača vremena
Zasvijetli kada odaberete funkciju Timer (Mjerač vremena)
POSTAVKE TJEDNOG MJERAČA VREMENA
RJEŠAVANJE PROBLEMA
POSTAVKE DNEVNOG MJERAČA VREMENA
ODABIR MJERAČA VREMENA
65
7 8
5 6
7 8
HOW TO SELECT THE TIMER HOW TO SELECT THE TIMER
WEEKLY TIMER SETTING WEEKLY TIMER SETTING
Cancel Current Timer Program
Perform the steps below to cancel the timer program for a particular day.
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
4
2
1
,
3
1. Press
SELECT
to enter day.
2. Press Timer
UP
or
DOWN
until your desired day is shown.
3. Press
SELECT
to enter program setting.
4. Press Timer
UP
or
DOWN
until your desired day is shown.
Press
CANCEL
to cancel the program, will disappear.
For example, if you want to set:
A - Monday to Friday: Unit ON at 09:00 with 20°C (program 1) & unit OFF at 18:30 (program 2).
B - Only Wednesday: Add timer to turn OFF the unit at 12:30 (program 3) and turn ON the unit at 13:30
(program 4).
■
To set A (Monday to Friday – Collective day setting)
To set the time, please refer to steps 1 to 7 of “Day and Timer Set Up Method” on page 7.
Program 1 – select ON, set desired time to 9:00 and desired temperature to 20°C.
Program 2 – select OFF and set desired time to 18:30.
Program 3 ~ 6 – no timer program set, press
MODE
or wait 30 seconds to exit weekly timer.
■
To set B (Wednesday – add new timer program)
1. Press Timer
MODE
to enter timer mode.
2. Press Timer
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until “WED” is selected, press
SELECT
to con rm your selection.
4. Perform steps 4 to 7 of “Day and Timer Set Up Method” to add program 3 and program 4.
Note: Timer that has setting nearest to the current time and day will be activated first.
Disable & Enable Weekly Timer
• To disable weekly timer setting, press
MODE
, then press
CANCEL
.
• To enable previous weekly timer setting, press
MODE
, then press
SET
.
TROUBLESHOOTING TROUBLESHOOTING
The following symptoms occur when abnormality occurs during operation.
• The unit stops and operation LED OFF.
• OFF indicator does not shown on remote control display.
When abnormality occurs, use remote control to retrieve error code.
OFF
/
ON
TIMER/CLOCK
FAN SPEED
MODE
CHECK
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
OFF
Indicator
1
,
3
2
Operation
LED
Ensure the operation LED is in OFF condition.
1. Press for 5 seconds.
2. Press
UP
or
DOWN
. If error code and abnormality can be
identi ed, the operation LED will be ON continuously, then jot
down the error code.
3. Press for 5 seconds to quit checking.
4. Reveal the error code to authorized dealer.
Printed in China
OSTH0901-01
DAILY TIMER SETTING DAILY TIMER SETTING
►How to Set Weekly Timer
- You can set the Timer for each day of the week (Monday to Sunday) with 6 programs per day.
- ON Timer can be set together with your desired temperature and this temperature will be used
continuously.
- Same timer program cannot be set in the same day.
- You may also select collective days with same timer setting.
- Promotes energy saving by allowing you to set up to 6 programs in any given day.
Day and Timer Set Up Method
1. Press Timer
MODE
for 4 seconds to change display to weekly timer.
2. Press Timer
UP
or
DOWN
to select your desired day.
3. Press
SELECT
to con rm your selection.
4. “1” will be blinking, press
SELECT
to set program 1.
5. Press Timer
OFF/ON
to select ON or OFF timer.
6. Press Timer
UP
or
DOWN
to select your desired time.
If you want to set the timer together with your desired temperature, press
TEMP
to select the temperature.
7. Press
SET
to con rm program 1. The selected day will be highlighted with .
• After 2 seconds, the display will move to the next program. Repeat steps 4 to 7 to set programs 2 to 6.
• During timer setup, if no button is pressed within 30 seconds, or if the
SET
button is pressed, the setting at
that moment is con rmed and timer setup is ended.
Check Current Timer Program
Perform the steps below to check the timer program for a particular day.
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is shown, press
SELECT
to con rm your selection.
4. Press Timer
UP
or
DOWN
to check the set programs.
Modify Current Timer Program or Add New Timer Program
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is shown.
4. Perform steps 4 to 7 of “Day and Timer Set Up Method” to modify existing timer program, or add any timer
program.
►How to Set Daily Timer
- You can set ON timer only or OFF timer only or both ON and OFF timer in a day.
1 Change Display
Press Timer
MODE
to change the display to daily timer.
2 Press Timer
OFF/ON
to select ON or OFF timer.
Example: To turn ON the unit at 09:00
Press Timer
OFF/ON
to select ON timer.
Press
UP
or
DOWN
to select the desired time, then press
SET
to con rm the selected time.
Or press
CANCEL
if you do not want any setting for ON Timer.
Example: To turn OFF the unit at 18:30
Press Timer
OFF/ON
to select OFF timer.
Press
UP
or
DOWN
to select the desired time, then press
SET
to con rm the selected time.
Or press
CANCEL
if you do not want any setting for OFF Timer.
Note:
• When ON timer is set, the unit may start early before the actual set time in order to achieve the
desired temperature on time.
• Timer operation is based on the clock set in the remote control and repeats daily once set.
For clock setting, please refer to Remote Control preparation.
• The timer closest to the current time will be activated rst.
• If timer is cancelled manually or due to power failure, you can restore the previous setting by
pressing
SET
.
Final Display of Daily Timer:
TIMER
ON
OFF
TIMER
ON
TIMER
OFF
Only ON Timer is selected.
The unit will automatically
switch ON at 9:00.
Only OFF Timer is selected.
The unit will automatically
switch OFF at 18:30.
Both ON and OFF Timer are
selected.
2 types of Timer mode can be selected on the remote control.
- Daily Timer
- Weekly Timer
- Daily timer and weekly timer could not be set at the same time.
- Select one of these Timers for your convenience.
How to Change the Display
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
Press
- Press once to change the display from CLOCK to Timer or vice-versa.
- Press for more than 4 seconds to change the display from Daily Timer to Weekly Timer or vice-versa.
Daily Timer Display
Lights up if Timer operation is selected
Time to be selected
(10 minutes step)
OFF Timer
To automatically switch “OFF” the unit
ON Timer
To automatically
switch “ON”
the unit
Weekly Timer Display
ON Timer
To automatically switch “ON” the unit
OFF Timer
To automatically switch “OFF” the unit
Time to be selected
(10 minutes step)
Indicates the selected day
6 different programs can be set
in a day (1 ~ 6)
Lights up if Timer operation is selected
Day to be selected
Indicates the next timer operation day
F566767-OSTH0901-01_1EN.indd 2 1/13/2009 11:06:43 AM
5 6
7 8
HOW TO SELECT THE TIMER HOW TO SELECT THE TIMER
WEEKLY TIMER SETTING WEEKLY TIMER SETTING
Cancel Current Timer Program
Perform the steps below to cancel the timer program for a particular day.
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
4
2
1
,
3
1. Press
SELECT
to enter day.
2. Press Timer
UP
or
DOWN
until your desired day is shown.
3. Press
SELECT
to enter program setting.
4. Press Timer
UP
or
DOWN
until your desired day is shown.
Press
CANCEL
to cancel the program, will disappear.
For example, if you want to set:
A - Monday to Friday: Unit ON at 09:00 with 20°C (program 1) & unit OFF at 18:30 (program 2).
B - Only Wednesday: Add timer to turn OFF the unit at 12:30 (program 3) and turn ON the unit at 13:30
(program 4).
■
To set A (Monday to Friday – Collective day setting)
To set the time, please refer to steps 1 to 7 of “Day and Timer Set Up Method” on page 7.
Program 1 – select ON, set desired time to 9:00 and desired temperature to 20°C.
Program 2 – select OFF and set desired time to 18:30.
Program 3 ~ 6 – no timer program set, press
MODE
or wait 30 seconds to exit weekly timer.
■
To set B (Wednesday – add new timer program)
1. Press Timer
MODE
to enter timer mode.
2. Press Timer
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until “WED” is selected, press
SELECT
to con rm your selection.
4. Perform steps 4 to 7 of “Day and Timer Set Up Method” to add program 3 and program 4.
Note: Timer that has setting nearest to the current time and day will be activated first.
Disable & Enable Weekly Timer
• To disable weekly timer setting, press
MODE
, then press
CANCEL
.
• To enable previous weekly timer setting, press
MODE
, then press
SET
.
TROUBLESHOOTING TROUBLESHOOTING
The following symptoms occur when abnormality occurs during operation.
• The unit stops and operation LED OFF.
• OFF indicator does not shown on remote control display.
When abnormality occurs, use remote control to retrieve error code.
OFF
/
ON
TIMER/CLOCK
FAN SPEED
MODE
CHECK
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
OFF
Indicator
1
,
3
2
Operation
LED
Ensure the operation LED is in OFF condition.
1. Press for 5 seconds.
2. Press
UP
or
DOWN
. If error code and abnormality can be
identi ed, the operation LED will be ON continuously, then jot
down the error code.
3. Press for 5 seconds to quit checking.
4. Reveal the error code to authorized dealer.
Printed in China
OSTH0901-01
DAILY TIMER SETTING DAILY TIMER SETTING
►How to Set Weekly Timer
- You can set the Timer for each day of the week (Monday to Sunday) with 6 programs per day.
- ON Timer can be set together with your desired temperature and this temperature will be used
continuously.
- Same timer program cannot be set in the same day.
- You may also select collective days with same timer setting.
- Promotes energy saving by allowing you to set up to 6 programs in any given day.
Day and Timer Set Up Method
1. Press Timer
MODE
for 4 seconds to change display to weekly timer.
2. Press Timer
UP
or
DOWN
to select your desired day.
3. Press
SELECT
to con rm your selection.
4. “1” will be blinking, press
SELECT
to set program 1.
5. Press Timer
OFF/ON
to select ON or OFF timer.
6. Press Timer
UP
or
DOWN
to select your desired time.
If you want to set the timer together with your desired temperature, press
TEMP
to select the temperature.
7. Press
SET
to con rm program 1. The selected day will be highlighted with .
• After 2 seconds, the display will move to the next program. Repeat steps 4 to 7 to set programs 2 to 6.
• During timer setup, if no button is pressed within 30 seconds, or if the
SET
button is pressed, the setting at
that moment is con rmed and timer setup is ended.
Check Current Timer Program
Perform the steps below to check the timer program for a particular day.
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is shown, press
SELECT
to con rm your selection.
4. Press Timer
UP
or
DOWN
to check the set programs.
Modify Current Timer Program or Add New Timer Program
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is shown.
4. Perform steps 4 to 7 of “Day and Timer Set Up Method” to modify existing timer program, or add any timer
program.
►How to Set Daily Timer
- You can set ON timer only or OFF timer only or both ON and OFF timer in a day.
1 Change Display
Press Timer
MODE
to change the display to daily timer.
2 Press Timer
OFF/ON
to select ON or OFF timer.
Example: To turn ON the unit at 09:00
Press Timer
OFF/ON
to select ON timer.
Press
UP
or
DOWN
to select the desired time, then press
SET
to con rm the selected time.
Or press
CANCEL
if you do not want any setting for ON Timer.
Example: To turn OFF the unit at 18:30
Press Timer
OFF/ON
to select OFF timer.
Press
UP
or
DOWN
to select the desired time, then press
SET
to con rm the selected time.
Or press
CANCEL
if you do not want any setting for OFF Timer.
Note:
• When ON timer is set, the unit may start early before the actual set time in order to achieve the
desired temperature on time.
• Timer operation is based on the clock set in the remote control and repeats daily once set.
For clock setting, please refer to Remote Control preparation.
• The timer closest to the current time will be activated rst.
• If timer is cancelled manually or due to power failure, you can restore the previous setting by
pressing
SET
.
Final Display of Daily Timer:
TIMER
ON
OFF
TIMER
ON
TIMER
OFF
Only ON Timer is selected.
The unit will automatically
switch ON at 9:00.
Only OFF Timer is selected.
The unit will automatically
switch OFF at 18:30.
Both ON and OFF Timer are
selected.
2 types of Timer mode can be selected on the remote control.
- Daily Timer
- Weekly Timer
- Daily timer and weekly timer could not be set at the same time.
- Select one of these Timers for your convenience.
How to Change the Display
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
Press
- Press once to change the display from CLOCK to Timer or vice-versa.
- Press for more than 4 seconds to change the display from Daily Timer to Weekly Timer or vice-versa.
Daily Timer Display
Lights up if Timer operation is selected
Time to be selected
(10 minutes step)
OFF Timer
To automatically switch “OFF” the unit
ON Timer
To automatically
switch “ON”
the unit
Weekly Timer Display
ON Timer
To automatically switch “ON” the unit
OFF Timer
To automatically switch “OFF” the unit
Time to be selected
(10 minutes step)
Indicates the selected day
6 different programs can be set
in a day (1 ~ 6)
Lights up if Timer operation is selected
Day to be selected
Indicates the next timer operation day
F566767-OSTH0901-01_1EN.indd 2 1/13/2009 11:06:43 AM
5 6
7 8
HOW TO SELECT THE TIMER HOW TO SELECT THE TIMER
WEEKLY TIMER SETTING WEEKLY TIMER SETTING
Cancel Current Timer Program
Perform the steps below to cancel the timer program for a particular day.
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
4
2
1
,
3
1. Press
SELECT
to enter day.
2. Press Timer
UP
or
DOWN
until your desired day is shown.
3. Press
SELECT
to enter program setting.
4. Press Timer
UP
or
DOWN
until your desired day is shown.
Press
CANCEL
to cancel the program, will disappear.
For example, if you want to set:
A - Monday to Friday: Unit ON at 09:00 with 20°C (program 1) & unit OFF at 18:30 (program 2).
B - Only Wednesday: Add timer to turn OFF the unit at 12:30 (program 3) and turn ON the unit at 13:30
(program 4).
■
To set A (Monday to Friday – Collective day setting)
To set the time, please refer to steps 1 to 7 of “Day and Timer Set Up Method” on page 7.
Program 1 – select ON, set desired time to 9:00 and desired temperature to 20°C.
Program 2 – select OFF and set desired time to 18:30.
Program 3 ~ 6 – no timer program set, press
MODE
or wait 30 seconds to exit weekly timer.
■
To set B (Wednesday – add new timer program)
1. Press Timer
MODE
to enter timer mode.
2. Press Timer
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until “WED” is selected, press
SELECT
to con rm your selection.
4. Perform steps 4 to 7 of “Day and Timer Set Up Method” to add program 3 and program 4.
Note: Timer that has setting nearest to the current time and day will be activated first.
Disable & Enable Weekly Timer
• To disable weekly timer setting, press
MODE
, then press
CANCEL
.
• To enable previous weekly timer setting, press
MODE
, then press
SET
.
TROUBLESHOOTING TROUBLESHOOTING
The following symptoms occur when abnormality occurs during operation.
• The unit stops and operation LED OFF.
• OFF indicator does not shown on remote control display.
When abnormality occurs, use remote control to retrieve error code.
OFF
/
ON
TIMER/CLOCK
FAN SPEED
MODE
CHECK
AIR SWING
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
OFF
Indicator
1
,
3
2
Operation
LED
Ensure the operation LED is in OFF condition.
1. Press for 5 seconds.
2. Press
UP
or
DOWN
. If error code and abnormality can be
identi ed, the operation LED will be ON continuously, then jot
down the error code.
3. Press for 5 seconds to quit checking.
4. Reveal the error code to authorized dealer.
Printed in China
OSTH0901-01
DAILY TIMER SETTING DAILY TIMER SETTING
►How to Set Weekly Timer
- You can set the Timer for each day of the week (Monday to Sunday) with 6 programs per day.
- ON Timer can be set together with your desired temperature and this temperature will be used
continuously.
- Same timer program cannot be set in the same day.
- You may also select collective days with same timer setting.
- Promotes energy saving by allowing you to set up to 6 programs in any given day.
Day and Timer Set Up Method
1. Press Timer
MODE
for 4 seconds to change display to weekly timer.
2. Press Timer
UP
or
DOWN
to select your desired day.
3. Press
SELECT
to con rm your selection.
4. “1” will be blinking, press
SELECT
to set program 1.
5. Press Timer
OFF/ON
to select ON or OFF timer.
6. Press Timer
UP
or
DOWN
to select your desired time.
If you want to set the timer together with your desired temperature, press
TEMP
to select the temperature.
7. Press
SET
to con rm program 1. The selected day will be highlighted with .
• After 2 seconds, the display will move to the next program. Repeat steps 4 to 7 to set programs 2 to 6.
• During timer setup, if no button is pressed within 30 seconds, or if the
SET
button is pressed, the setting at
that moment is con rmed and timer setup is ended.
Check Current Timer Program
Perform the steps below to check the timer program for a particular day.
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is shown, press
SELECT
to con rm your selection.
4. Press Timer
UP
or
DOWN
to check the set programs.
Modify Current Timer Program or Add New Timer Program
1. Press Timer
MODE
to enter timer mode.
2. Press
SELECT
to enter day setting.
3. Press Timer
UP
or
DOWN
until your desired day is shown.
4. Perform steps 4 to 7 of “Day and Timer Set Up Method” to modify existing timer program, or add any timer
program.
►How to Set Daily Timer
- You can set ON timer only or OFF timer only or both ON and OFF timer in a day.
1 Change Display
Press Timer
MODE
to change the display to daily timer.
2 Press Timer
OFF/ON
to select ON or OFF timer.
Example: To turn ON the unit at 09:00
Press Timer
OFF/ON
to select ON timer.
Press
UP
or
DOWN
to select the desired time, then press
SET
to con rm the selected time.
Or press
CANCEL
if you do not want any setting for ON Timer.
Example: To turn OFF the unit at 18:30
Press Timer
OFF/ON
to select OFF timer.
Press
UP
or
DOWN
to select the desired time, then press
SET
to con rm the selected time.
Or press
CANCEL
if you do not want any setting for OFF Timer.
Note:
• When ON timer is set, the unit may start early before the actual set time in order to achieve the
desired temperature on time.
• Timer operation is based on the clock set in the remote control and repeats daily once set.
For clock setting, please refer to Remote Control preparation.
• The timer closest to the current time will be activated rst.
• If timer is cancelled manually or due to power failure, you can restore the previous setting by
pressing
SET
.
Final Display of Daily Timer:
TIMER
ON
OFF
TIMER
ON
TIMER
OFF
Only ON Timer is selected.
The unit will automatically
switch ON at 9:00.
Only OFF Timer is selected.
The unit will automatically
switch OFF at 18:30.
Both ON and OFF Timer are
selected.
2 types of Timer mode can be selected on the remote control.
- Daily Timer
- Weekly Timer
- Daily timer and weekly timer could not be set at the same time.
- Select one of these Timers for your convenience.
How to Change the Display
TIMER/CLOCK
MODE
OFF/ON
CANCELCLOCK
SET
SELECTUP
DOWN
Press
- Press once to change the display from CLOCK to Timer or vice-versa.
- Press for more than 4 seconds to change the display from Daily Timer to Weekly Timer or vice-versa.
Daily Timer Display
Lights up if Timer operation is selected
Time to be selected
(10 minutes step)
OFF Timer
To automatically switch “OFF” the unit
ON Timer
To automatically
switch “ON”
the unit
Weekly Timer Display
ON Timer
To automatically switch “ON” the unit
OFF Timer
To automatically switch “OFF” the unit
Time to be selected
(10 minutes step)
Indicates the selected day
6 different programs can be set
in a day (1 ~ 6)
Lights up if Timer operation is selected
Day to be selected
Indicates the next timer operation day
F566767-OSTH0901-01_1EN.indd 2 1/13/2009 11:06:43 AM
Za jedan je dan moguće postaviti
6 različitih programa (1 ~ 6)
Pokazuje odabrani dan
Pokazuje sljedeći dan rada mjerača vremena
Vrijeme koje je potrebno odabrati
(pomak od 10 minuta)
Vrijeme isključivanja mjerača (OFF)
Automatsko isključivanje uređaja
Pokazatelj OFF
(Isključeno)
LED-svjetlo
koje označava
rad uređaja
-
1
-
2
Panasonic CZRD52CP Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Panasonic CZRD52CP Owner's manual
-
Panasonic CZRD514C Operating instructions
-
Panasonic WHMDC14C9E81 Operating instructions
-
Panasonic WHMXF12D9E8 Operating instructions
-
Panasonic WHMDF12C9E8 Operating instructions
-
Panasonic WHMDC05F3E5 Operating instructions
-
Panasonic CSE15NKEW Operating instructions
-
-
Panasonic SCPMX70BEG Operating instructions
-
Other documents
-
Sharp GX-M10HOR User manual
-
Vivax ACP-18COFM50AEEI User manual
-
Samsung NQ50J5530BS/EO User manual
-
Vaillant climaVAIR VAM 2-060 W2 User manual
-
Samsung NZ84J9770EK/EO User manual
-
-
Samsung NQ50H5537KB/EO User manual
-
Samsung HMX-W200RP User manual
-
Candy GC4 1072D3/2-S User manual
-