IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications bef
ore connecting the
product to the power source.
MTP U T A D • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate an Extron MTP U T A D universal transmitter.
Preparing the Mounting Surface
NOTE: Use a wall box with a depth of at least 2.5 inches (6.4 cm).
1. Place the wall box against the installation surface and mark the opening guidelines.
TIP: Use a level to properly orient the opening.
2. Cut out the material from the marked area.
3. Secure the wall box with 10-penny nails or #8 or #10 screws, leaving the front edge ush with the outer wall or furniture surface.
4. Run all required cables (see Rear Panel Connections) and secure them with cable clamps.
Front Panel Inputs
4
5
1
2
0
E
8
7
6
3
9
A
D
B
C
F
INPUTS
VIDEO
AUDIO INPUT
COMPUTER INPUT
MONITOR OUT
S-VIDEO
PWRVID S-VIDYUV PC
AUDIO
L
EDID SELECT
CONTACT
PRE-PEAK
50Hz REFRESH
RPr
Pb
Y
YUV
ON
12
3
1234
12V
.5A MAX
OUTPUT
Side
11
2
2
3
3
4
4
5
5
66
77
88
9
9
¢
¢
1
Plug a computer (VGA) video source into the Computer Input 15-pin HD connector.
2
Plug a VGA monitor into the Monitor Out 15-pin HD connector.
3
Plug a high definition or standard definition component video source into the YUV RCA
connectors.
4
Plug a composite video source into the Video RCA connector.
5
Plug an S-video source into the S-video 4-pin mini-DIN connector.
6
Plug a stereo audio source into the audio RCA connectors.
7
Plug a stereo audio source into the 3.5 mm mini jack connector.
Rear Panel Connections
4
5
1
2
0
E
8
7
6
3
9
A
D
B
C
F
INPUTS
VIDEO
AUDIO INPUT
COMPUTER INPUT
MONITOR OUT
S-VIDEO
PWRVID S-VIDYUV PC
AUDIO
L
EDID SELECT
CONTACT
PRE-PEAK
50Hz REFRESH
RPr
Pb
Y
YUV
ON
12
3
1234
12V
.5A MAX
OUTPUT
Side
11
2
2
3
3
4
4
5
5
6
6
7
7
88
9
9
¢
¢
8
Terminate a TP cable as shown below at right. Connect it between the transmitter Output port
and the receiver Input port (both ends need to match).
9
Wire the 5-pole captive screw connector for the contact closure control of input selections
as shown below. To select a video input as the transmitter output, momentarily tie the
Pin
1
2
3
4
5
6
7
8
Wire color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
12345678
Inse
rt Twisted
Pair Wires
Pins:
assigned pin for that format to ground.
¢
Wire the 2-pole captive screw connector for the included external 12 VDC, 1 A power
supply (see image and grounding instructions on the next page).
ATTENTION: Do not connect these devices to a computer or telecommunications
network.
Contact closure input selection connector wiring:
Pin Format Pin Format Pin Ground
1 Composite 3 YUV 5 Ground
2 S-video 4 PC
NOTE: If you are using an
Enhanced Skew-Free™ A/V
cable, use the TIA/EIA T568A
standard only.
68-1674-50 Rev. E
04 17
MTP U T A D • Setup Guide
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Australia
+61.8.8113.6800
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2017 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Grounding the Power Input Port
Power Supply
Output Cord
SECTION A–A
Ridge
s
Smooth
AA
POWER
12V
xA MAX
Tie
Wrap
Rear
Panel
Ridges
Earth
Ground
3/16
"
(5 mm
)
Max.
Extron MTP U T A D transmitters can be adversely affected by electrostatic discharge (ESD)
if they are not grounded correctly.
To prevent malfunctions or product damage, an experienced installer can correctly ground
an Extron MTP U T A D transmitter product by inserting one end of the grounding wire to the
negative or ground pin on the power input connector (see the image on the right). Tie the
other end of the wire to an earth ground.
Plug the connector into the MTP U T A D transmitter.
If you have any questions about how to ground a product in a specic application, contact an
Extron technical support specialist.
Front Panel Switch Settings and LEDs
• DIP Switches
• Contact — Set this switch on (up) for contact closure control of the input selection. Set the switch off (down) for auto switch mode (the
transmitter automatically selects the highest format video input with a sync signal present).
• Pre-Peak — View the image and set the Pre-Peaking switch for the best image quality to correct for long cable runs of the entire sytem
• 50 Hz Refresh — Set this switch on (up) for a 50 Hz refresh rate for the resolution selected by the EDID Select switch. Set this switch
off (down) for 60 Hz.
• EDID Select rotary switch — Set this switch to one of the positions below to select either the local monitor as the source of the EDID data
or a specic resolution.
• Position 0 — The loop-through monitor (2, on the other side of this guide) is the source of the EDID data.
• Position 1 - F — Specify a resolution. The table below identies the switch positions and the associated resolutions. By default, the
vertical refresh rate for all resolutions is 60 Hz. The resolution can be set to 50 Hz using the Refresh DIP switch.
Position
Source or
Resolution
Position Resolution Position Resolution Position Resolution
0 Local monitor 4 1280 x 768 8 1366 x 768 C 1680 x 1050
1 800 x 600 5 1280 x 800 9 1400 x 1050 D 1920 x 1080
2 1024 x 768 6 1280 x 1024 A 1440 x 900 E 1920 x 1200
3 1280 x 720 7 1360 x 768 B 1600 x 1200 F Not used
• LEDs —
• Power — This LED indicates power is applied to the MTP.
Decorator
-Style
Faceplate
W
all opening
is ush with
edge of box.
Installation
Cable
Cable Clamp
Wall Stud
4
5
1
2
0
E
8
7
6
3
9
A
D
B
C
F
DDC
RESOL
.
SWITCH MODE
PRE-PEAK
REFRESH 50/60Hz
ON
1 2
3
AUDIO INPUT
COMPUTER INPUT
MONITOR OUT
P
WR VID
Y/C YUV RGB
INPUTS
VIDEO S-VIDEO
AUDIO
L
RPr
Pb
Y
YUV
MTP U T A D
Transmitter
• Active input — The lit LED: PC, YUV, S-VID, or Vid; indicates the video input connector
that is selected for transmission.
Final Installation
1. Make all connections, test the system, and install the device when operation is satisfactory.
2. At the power outlet, unplug the power supply.
3. Mount the transmitter into the wall box, and attach the supplied Decorator-Style faceplate to
the unit.
4. At the power outlet, reconnect the power supply.
4
5
1
2
0
E
8
7
6
3
9
A
D
B
C
F
EDID
SELECT
CONTACT
PRE-PEAK
50 Hz REFRES
H
ON
123
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Extron WPD 100 Audio Series Owner's manual
-
-
-
-
-
-
Extron MTP 1500RL 15HD A SEQ User manual
-
Extron MTP T 15HD A D User manual
-
-
Other documents
-
Extron electronics VersaTools MTP 15HD A Series User manual
-
Extron electronics MTP U Series User manual
-
Extron electronics Multi-Graphic Processor MGP 464 User manual
-
Extron electronics 305SA User manual
-
Extron electronics 3G-HD User manual
-
Extron electronic DVS 304 AD User manual
-
Extron electronics DSC HD-HD User manual
-
Extron electronics XTP SR HDMI User manual
-
Extron electronics DTP T SW4 HD 4K User manual
-
