BrandMotion FLTW-7627 Installation guide

BrandMotion
Brand
BrandMotion
Model
FLTW-7627
Type
Installation guide

BrandMotion FLTW-7627 is a plug-and-play harness that allows you to add a cargo camera to your vehicle. It is compatible with vehicles that have an existing backup camera. The harness includes a toggle switch that allows you to switch between the OEM backup camera and the cargo camera.

Here are some of the features and possible use cases of the BrandMotion FLTW-7627:

  • Easy to install, no cutting or splicing of wires required.
  • Works with most aftermarket cargo cameras.
  • Allows you to view the cargo camera on your vehicle's display.
  • Can be used to monitor cargo or trailers while driving.

BrandMotion FLTW-7627 is a plug-and-play harness that allows you to add a cargo camera to your vehicle. It is compatible with vehicles that have an existing backup camera. The harness includes a toggle switch that allows you to switch between the OEM backup camera and the cargo camera.

Here are some of the features and possible use cases of the BrandMotion FLTW-7627:

  • Easy to install, no cutting or splicing of wires required.
  • Works with most aftermarket cargo cameras.
  • Allows you to view the cargo camera on your vehicle's display.
  • Can be used to monitor cargo or trailers while driving.
INSTALLATION INSTRUCTIONS
RAM Cargo Camera Plug and Play Harness
(Kit # FLTW-7627)
Please read thoroughly before starting installation and check that kit contents are complete.
Items Included in the Kit:
Tools & Supplies Needed:
Factory T-harness
These instructions
Wire cutters
Wire strippers
Zip ties
Electrical tape
Heat shrink
Torx t20
7mm socket
Plastic panel removal tools
Safety Precautions:
● Work in well ventilated area that is clear of obstructions.
● Secure vehicle with tire chucks in both front and rear of tires.
● Turn vehicle accessories OFF and ensure ignition key is in OFF position.
● Wear safety goggles and snug fitting clothes.
● Use tools only for their intended purpose and which are in good repair.
● Only perform this task if confidence, skill, and physical ability permit.
NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color
instructions, as well as an installation video, please visit www.brandmotion.com
FLTW-7627 instructions 10-20-2020 Page 1 of 2 KB
INSTALLATION INSTRUCTIONS
INSTALLING:
1. Remove trim around screen/display.
2. Remove screws that hold screen to dash.
3. Disconnect main 52-pin harness from the back of the screen by lifting up on the “handle” to release the
plug.
4. Plug in the main 52-pin factory harness that was just unplugged, into the female end of the T-harness.
5. Plug in the male 52-pin plug from the T-harness into the factory screen/display. Lock the plug in by
pushing down on the “handle”.
6. Connect the RED wire from the T-harness labeled “ACC” to a 12V accessory source.
7. Connect the RED wire from the T-harness labeled “CAMERA POWER” to the power input wire for your
camera. The toggle switch on this wire will control the power to the camera to switch between OEM
backup and Cargo camera views.
8. Connect your cargo camera (not supplied) RCA to the “CAMERA IN” RCA.
9. If you have an existing OEM backup camera, leave the VIDEO 1 RCA taped to the OEM CAMERA RCA.
If you are adding an aftermarket camera, untape and connect the aftermarket camera to the VIDEO 1
RCA.
10. Mount the toggle switch in an accessible position. Position 1 enables VIDEO 1 display when in reverse;
position 2 enables VIDEO 2 display in reverse.
***NOTE: FOR THIS HARNESS TO WORK CORRECTLY, THE VEHICLE MUST HAVE AN
EXISTING BACKUP CAMERA. OTHERWISE, IT WILL HAVE TO BE TAKEN TO A DEALER AND
UPDATED.***
FLTW-7627 instructions 10-20-2020 Page 2 of 2 KB
  • Page 1 1
  • Page 2 2

BrandMotion FLTW-7627 Installation guide

BrandMotion
Brand
BrandMotion
Model
FLTW-7627
Type
Installation guide

BrandMotion FLTW-7627 is a plug-and-play harness that allows you to add a cargo camera to your vehicle. It is compatible with vehicles that have an existing backup camera. The harness includes a toggle switch that allows you to switch between the OEM backup camera and the cargo camera.

Here are some of the features and possible use cases of the BrandMotion FLTW-7627:

  • Easy to install, no cutting or splicing of wires required.
  • Works with most aftermarket cargo cameras.
  • Allows you to view the cargo camera on your vehicle's display.
  • Can be used to monitor cargo or trailers while driving.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents