2. Neutrik
  3. NL2FRX
NL2FRX

Neutrik NL2FRX User manual

  • I am a chat assistant and I have reviewed the assembly instructions for the NEUTRIK SPX Series NL2FX and NL2FRX loudspeaker connectors. The document provides detailed steps for assembling these lockable connectors, including cable preparation, terminal securing, and the use of a conversion kit LRX. I'm ready to answer your questions about the device's assembly process, specifications, and usage, as described in this document.
  • What is the maximum torque for securing the terminals?
    What screwdriver should be used for assembling the terminals?
    What is the recommended stripping length for the cable wires?
    Can speakON connectors be used as a mains power supply connector?
Assembly of the Connector:
Place bushing and chuck over cable.
Prepare cable as shown.
Important is the stripping length of 25 mm and
12 mm.
Insert wires into terminals and secure clamp
terminals with screw driver (POZIDRIV # 1)
®
at max. torque 0.8 Nm.
For 6 mm (AWG 10) remove screws, clamping
2
sheet and solder.
Push chuck up to housing .
Important: Align the chuck by positioning
the nose into the recess.
Finish installation by turning the bushing
onto the connector.
INFO to the screw driver:
DO NOT USE!
POZIDRIV # 1 Philips
®
A
B
C
D
E
A
B
C
NL2FX / NL2FRX
®
speakON SPX Series Lockable Loudspeaker Connector
R
BDA 348
IMPORTANT SAFETY INSTRUCTION
“CAUTION: NOT FOR INTERRUPTING CURRENT”
“ ATTENTION: NE PAS UTILISER POUR COUPER LE COURANT”
E
Page 1
Attention: speakON is not to be used as an AC mains or power supply connector!
1.
2.
12 mm [0.5"]
25 mm [1.0"]
1+
1-
1-
1+
D
E
X
Cable O.D. 6.0 - 10.0 mm
[0.24 - 0.39”]
2
Wire size 1.5 - 4 mm
(AWG 12)
ð
Electrical Rating acc. UL & CSA:
USR: 40A/250V, CNR: 25A/250V
ASSEMBLY INSTRUCTION
ASSEMBLY INSTRUCTION speakON NL2FX / NL2FRX
I
Assembly of the Conversion Kit LRX:
www.neutrik.com
NEUTRIK AG LI T: +423 / 237 24 24 F: +423 / 232 53 93
NEUTRIK USA Inc. USA T: +1 704 / 972 3050 F: +1 704 / 438 9202
( )
NEUTRIK UK Ltd. UK T: +44 1983 / 811 441 F: +44 1983 / 811 439
NEUTRIK Vertriebs GmbH DE / NL / AT/DK T: +49 8131 / 280 890 F: +49 8131 / 280 830
NEUTRIK France FR T: +33 1 / 4131 6750 F: +33 1 / 4131 0511
NEUTRIK Tokyo Ltd. JP T: +81 3 / 3663 4733 F: +81 3 / 3663 4796
NEUTRIK Hong Kong Ltd. HK T: +852 / 2687 6055 F: +852 / 2687 6052
NEUTRIK India Pvt. Ltd. IND T: +91 / 982 05 43 424 F: +91 / 22 26163 540
R
Draft. Nr.: BDA 348 Update: 22.11.2016 Data subject to change without prior notice. 2016 NEUTRIK . ALL RIGHTS RESERVED. NEUTRIK is a registered trademark.
I I ® ®
©
Open the bushing.
Slide the bushing and the chuck back.
Bend the cable as shown.
Position the two conversion shells to fit on
the connector thread.
Press together and fix by screw.
Slide the chuck onto the housing and fasten
the bushing.
Important: Align the chuck by positioning
the nose into the recess.
A
B
C
D
E
A
B
C
D
E
F
F
1.
2.
F
Find more details of speakCON on www.neutrik.com.
/