PROEL WAVE12P User manual
- Category
- Audio amplifiers
- Type
- User manual
This manual is also suitable for
WAVE series
WAVE10P - WAVE12P - WAVE15P
passive loudspeakers
USER MANUAL
MANUALE D'USO
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of
its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this
from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should
contact either the retailer where they purchased this product, or their local government offi ce, for details of where and how they can
take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and condi ons of the
purchase contract. This product should not be mixed with other commercial wastes for disposal.
The lightning fl ash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure, that may be of suffi cient magnitude to cons tute a risk of electric shock to persons.
The exclama on point within an equilateral triangle is intended to alert the user to the presence of important opera ng and maintenance
(servicing) instruc ons in the literature accompanying the appliance.
The informa on contained in this publica on has been carefully prepared and checked. However no responsibility will be taken for any errors. All
rights are reserved and this document cannot be copied, photocopied or reproduced in part or completely without wri en consent being obtained
in advance from PROEL. PROEL reserves the right to make any aesthe c, func onal or design modifi ca on to any of its products without any prior
no ce. PROEL assumes no responsibility for the use or applica on of the products or circuits described herein.
Il marchio riportato sul prodo o o sulla documentazione indica che il prodo o non deve essere smal to con altri rifi u domes ci al
termine del ciclo di vita. Per evitare eventuali danni all’ambiente si invita l’utente a separare questo prodo o da altri pi di rifi u e di
riciclarlo in maniera responsabile per favorire il riu lizzo sostenibile delle risorse materiali. Gli uten domes ci sono invita a conta are
il rivenditore presso il quale è stato acquistato il prodo o o l’uffi cio locale preposto per tu e le informazioni rela ve alla raccolta
diff erenziata e al riciclaggio per questo po di prodo o. Gli uten
aziendali sono invita a conta are il proprio fornitore e verifi care i
termini e le condizioni del contra o di acquisto. Questo prodo o non deve essere smal to unitamente ad altri rifi u commerciali.
Il simbolo del lampo con freccia in un triangolo equilatero intende avver re l'u lizzatore per la presenza di "tensioni pericolose" non isolate
all'interno dell'involucro del prodo o, che possono avere una intensità suffi ciente a cos tuire rischio di scossa ele rica alle persone.
Il punto esclama vo in un triangolo equilatero intende avver re l'u lizzatore per la presenza di importan istruzioni per l'u lizzo e la
manutenzione nella documentazione che accompagna il prodo o.
Le informazioni contenute in questo documento sono state a entamente reda e e controllate. Tu avia non è assunta alcuna responsabilità per
eventuali inesa ezze. Tu i diri sono riserva e questo documento non può essere copiato, fotocopiato, riprodo o per intero o in parte senza
previo consenso scri o della PROEL. PROEL si riserva il diri o di apportare senza preavviso cambiamen e modifi che este che, funzionali o di
design a ciascun proprio prodo o. PROEL non assume alcuna responsabilità sull’uso o sull’applicazione dei prodo o dei circui qui descri .
INDEX
TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . 3
FREQUENCY RESPONSE . . . . . . . . . . . . . . . . . . . . . 3
DIMENSIONS AND FLYING POINTS . . . . . . . . . . . . . 4
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SPARE PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
INPUT PANEL (FIG.1) . . . . . . . . . . . . . . . . . . . . . . . . 6
CONNECTIONS (FIG.2) . . . . . . . . . . . . . . . . . . . . . . 6
CONFIGURATIONS (FIG.3) . . . . . . . . . . . . . . . . . . . 7
SAFETY AND PRECAUTIONS . . . . . . . . . . . . . . . . . . 8
IN CASE OF FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . 8
CE CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PACKAGING, SHIPPING AND COMPLAINT . . . . . . . 8
WARRANTY AND PRODUCTS RETURN . . . . . . . . . . 9
INSTALLATION AND DISCLAIMER . . . . . . . . . . . . . . 9
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . 10
INSTRUCTIONS (FIG. 1 / 2 / 3) . . . . . . . . . . . . . . . 10
INDICE
SPECIFICHE TECNICHE . . . . . . . . . . . . . . . . . . . . . . 3
RISPOSTA IN FREQUENZA . . . . . . . . . . . . . . . . . . . . 3
DIMENSIONI E PUNTI DI SOSPENSIONE. . . . . . . . . 4
ACCESSORI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PARTI DI RICAMBIO. . . . . . . . . . . . . . . . . . . . . . . . . 5
PANNELLO INGRESSI (FIG.1) . . . . . . . . . . . . . . . . . . 6
CONNESSIONI (FIG.2) . . . . . . . . . . . . . . . . . . . . . . . 6
CONFIGURAZIONI (FIG.3) . . . . . . . . . . . . . . . . . . . . 7
AVVERTENZE PER LA SICUREZZA . . . . . . . . . . . . . 12
IN CASO DI GUASTO . . . . . . . . . . . . . . . . . . . . . . . 12
PROBLEMATICHE COMUNI . . . . . . . . . . . . . . . . . . 12
CONFORMITÀ CE . . . . . . . . . . . . . . . . . . . . . . . . . . 12
IMBALLAGGIO, TRASPORTO E RECLAMI . . . . . . . 12
GARANZIE E RESI . . . . . . . . . . . . . . . . . . . . . . . . . 13
INSTALLAZIONE E LIMITAZIONI D’USO . . . . . . . . . 13
INFORMAZIONI GENERALI . . . . . . . . . . . . . . . . . . 14
ISTRUZIONI (FIG. 1 / 2 / 3) . . . . . . . . . . . . . . . . . . 14
3
FREQUENCY RESPONSE RISPOSTA IN FREQUENZA
WAVE10P
MODEL WAVE10P WAVE12P WAVE15P
System type 2-way vented enclosure 2-way vented enclosure 2-way vented enclosure
High Frequency Device 1’’ compression driver 1" VC 1’’ compression driver 1.35" VC 1’’ compression driver 1.35" VC
Low Frequency Device 10” woofer with 1.5" VC 12” woofer with 2" VC 15” woofer with 2.5" VC
Angular Coverage 90° H x 60° V 90° H x 60° V 90° H x 60° V
Nominal Impedance 8 ohm 8 ohm 8 ohm
Power RaƟ ng (conƟ nuous) 150 W 200 W 250 W
Power RaƟ ng (peak) 300 W 400 W 500 W
Frequency Response 70 Hz - 20 kHz 60 Hz - 20 kHz 50 Hz - 20 kHz
SensiƟ vity (1 W / 1 m) 93 dBspl 94 dBspl 95 dBspl
Max SPL at 1mt (peak) 118 dBspl 120 dBspl 122 dBspl
Crossover Frequency 2400 Hz 1800 Hz 1800 Hz
Connectors INPUT, LINK:
Neutrik SPEAKON© (NL4MP)
INPUT, LINK:
Neutrik SPEAKON© (NL4MP)
INPUT, LINK:
Neutrik SPEAKON© (NL4MP)
ConstrucƟ on Polypropylene Polypropylene Polypropylene
Cabinet Colour Black Black Black
Flying System 2 x M8 bo om 4 x M10 top and bo om 4 x M10 top and bo om
1 x M10 rear
Handles 1 x top 1 x top, 2 x side 1 x top, 2 x side
MounƟ ng Pole 1 x bo om 1 x bo om 1 x bo om
Weight 11 kg (24.2 lb) 14 kg (30.8 lb) 18 kg (36.4 lb)
Dimensions (W x H x D) 320 x 500 x 290 mm 390 x 620 x 350 mm 480 x 740 x 430 mm
TECHNICAL SPECIFICATIONS SPECIFICHE TECNICHE
WAVE15P
WAVE12P
10k5k2k1k5002001005040 20kHz
120.0
dBSPL
110.0
100.0
90.0
80.0
70.0
10k5k2k1k5002001005040 20kHz
120.0
dBSPL
110.0
100.0
90.0
80.0
70.0
10k5k2k1k500
200
10050
40
20kHz
120.0
dBSPL
110.0
100.0
90.0
80.0
70.0
4
DIMENSIONS AND FLYING POINTS DIMENSIONI E PUNTI DI SOSPENSIONE
50 cm
19.7"
62 cm
24.4"
74 cm
29.1"
48 cm
18.9"
43 cm
16.9"
39 cm
15.4"
35 cm
13.8"
32 cm
12.6"
29 cm
11.4"
M10 Flying points
M10 Flying points
M10 Flying points
M10 Flying points
M8 Flying points
MounƟng Pole
MounƟng Pole
MounƟng Pole
M10 Flying point
WARNING: DO NOT SUSPEND THE CABINETS FROM
THE HANDLES.
AVVERTENZA: NON SOSPENDERE GLI ALTOPARLANTI
DALLE MANIGLIE.
5
ACCESSORIES
KP210
Adjustable speaker pole for speaker-subwoofer separa on
with terminal pieces Ø 35 mm. Supplied with a bolt
locking mechanism incorpora ng a steel pin for extra
safety. Adjustment: 825 - 1320 mm.
ACCESSORI
KP210
Supporto distanziatore cassa-subwoofer regolabile in
acciaio con terminali Ø 35mm. Dotato di meccanismo
di chiusura a vite con pin di sicurezza in acciaio.
Regolazione: 825 - 1320 mm.
FRE300BK
Professional aluminium floor-stand for speaker
with terminal pieces Ø 35mm. Supplied with
a screw locking system, a steel safety pin and
“Aircushioned” air-damped release device to grant
a fl exible, fast and easy adjustment. Adjustment:
1470-2180 mm.
FRE300BK
Supporto professionale in alluminio da pavimento
con terminali Ø 35mm. Con sistema di blocco a
vite, pin di sicurezza in acciaio e disposi vo di
smorzamento ad aria per la massima velocità e
facilità di regolazione.
Regolazione: 1470-2180 mm.
KP565
Wall mount heavy duty steel tube speaker
stand. The direc onal moun ng bracket allows
both horizontal and ver cal adjustment.
KP565
Robusto supporto in acciaio tubolare a parete
per casse acustiche. Lo snodo direzionale
permette una regolazione completa, sia
ver cale che orizzontale.
AC169
Golfare in acciaio zincato nero MA10 per
sospensione.
AC169
Black galvanized steel eyebolt MA10 for flying
mount.
SPARE PART LIST PARTI DI RICAMBIO
CODE DESCRIPTION
96PCAGWAVE10P WAVE10P XOVER PCBA
96PCAGWAVE12P WAVE12P XOVER PCBA
96PCAGWAVE15P WAVE15P XOVER PCBA
98LT10WFZ8 WOOFER 10” 8 OHM (WAVE10P)
98WAVE12WFZ8 WOOFER 12” 8 OHM (WAVE12P)
98WAVE15WFZ8 WOOFER 15” 8 OHM (WAVE15P)
98LTDR100Z8 DRIVER 1” 1” VC (WAVE10P)
98LTDR135Z8 DRIVER 1” 1.35” VC (WAVE12/15P)
NL4MP SPEAKON CONNECTOR
CODICE DESCRIZIONE
96PCAGWAVE10P CROSSOVER WAVE10P
96PCAGWAVE12P CROSSOVER WAVE12P
96PCAGWAVE15P CROSSOVER WAVE15P
98LT10WFZ8 WOOFER 10” 8 OHM (WAVE10P)
98WAVE12WFZ8 WOOFER 12” 8 OHM (WAVE12P)
98WAVE15WFZ8 WOOFER 15” 8 OHM (WAVE15P)
98LTDR100Z8 DRIVER 1” 1” VC (WAVE10P)
98LTDR135Z8 DRIVER 1” 1.35” VC (WAVE12/15P)
NL4MP CONNETTORE SPEAKON
6
INPUT PANEL (FIG.1) PANNELLO INGRESSI (FIG.1)
CONNECTIONS (FIG.2) CONNESSIONI (FIG.2)
LOUDSPEAKER LINE LOSSES
(maximum permissible line lengths for 0.5dB losses, voltage or spl)
8 ohm load 4 ohm load Wire sec on
data
PROEL recommended
cables
meter feet meter feet mm² AWG 2 wires
fl ex-black
2 wires FR
installa on
50 164 25 82 4.0 12 HPC624BK HPC624FRS
30 100 15 50 2.5 14 HPC620BK HPC620FRS
20 66 10 33 1.5 16 HPC610BK HPC610FRS
this is a short extrac on of the wide assortment of cables available from
PROEL, please visit our website at www.proel.com
Perdite di collegamento
(massima lunghezza per perdite inferiori a 0.5dB, tensione o spl)
carico 8 ohm carico 4 ohm Sezione del
cavo
Cavi PROEL consiglia
metri feet metri feet mm² AWG 2 fi li nero
fl essibile
2 fi li da in-
stallazione
50 164 25 82 4.0 12 HPC624BK HPC624FRS
30 100 15 50 2.5 14 HPC620BK HPC620FRS
20 66 10 33 1.5 16 HPC610BK HPC610FRS
questo è un breve estra o del vasto assor mento di cavi disponibile da PROEL,
vi preghiamo di visitare il nostro sito web all'indirizzo www.proel.com
INPUT - LINK (ingresso-rilancio)
ConneƩore per cavo Ɵpo Speakon Neutrik NL2FX
PROEL code - NL2FX
Codice PROEL - NL2FX
INPUT - LINK
Neutrik NL2FX Speakon Cable Connector
1+
1-
20mm
0.8"
8mm
0.3"
RED
BLACK
posiƟve / red / rosso
1+
negaƟve / black / nero
1-
7
CONFIGURATIONS (FIG.3) CONFIGURAZIONI (FIG.3)
RIGHT
single speaker
8 ohm load
LEFT
single speaker
8 ohm load
WAVE passive BASIC STEREO sound system
RIGHT
paralled speakers
4 ohm load
LEFT
paralled speakers
4 ohm load
WAVE passive DOUBLE PARALLEL STEREO sound system
8
SAFETY AND PRECAUTIONS
• CAUTION: before using this product read carefully the following safety instruc ons. Take a look of this manual en rely and preserve it for
future reference.
When using any electric product, basic precau ons should always be taken, including the following:
– To reduce the risk, close supervision is necessary when the product is used near children.
– Protect the apparatus from atmospheric agents and keep it away from water, rain and high humidity places.
– This product should be site away from heat sources such as radiators, lamps and any other device that generate heat.
– This product should be located so that its loca on or posi on does not interfere with its proper ven la on and hea ng dissipa on.
– Care should be taken so that objects and liquids do not go inside the product.
– This product may be capable of producing sound levels that could cause
permanent hearing loss. Exposure to extremely high noise levels may cause
permanent hearing loss. Individuals vary considerably in suscep bility to noise-
induced hearing loss, but nearly everyone will lose some hearing if exposed
to sufficiently intense noise for a period of time. The U.S. Government’s
Occupational Safety and Health Administration (OSHA) has specified the
permissible noise level exposures shown in the following chart. According to
OSHA, any exposure in excess of these permissible limits could result in some
hearing loss. To ensure against poten ally dangerous exposure to high sound
pressure levels, it is recommended that all persons exposed to equipment
capable of producing high sound pressure levels use hearing protectors while
the equipment is in opera on. Ear plugs or protectors in the ear canals or over
the ears must be worn when opera ng the equipment in order to prevent
permanent hearing loss if exposure is in excess of the limits set forth here. Keep
your's a en on that children and pets are more suscep ble to excessive noise
levels.
IN CASE OF FAULT
• In case of fault or maintenance this product should be inspected only by qualifi ed service personnel when:
– There is a fl aw either in the connec ons or in the supplied connec ng cables.
– Liquids have spilled inside the product.
– The product has fallen and been damaged.
– The product does not appear to operate normally or exhibits a marked change in performance.
– The product has been lost liquids or gases or the enclosure is damaged.
• Do not operate on the product, it has no user-serviceable parts inside, refer servicing to an authorized maintenance centre.
TROUBLESHOOTING
No Sound • Is the loudspeaker cable connected?
• Is the SPEAKON cable connector correctly inserted? turn it clockwise un l it clicks.
• Are you sure your power cable works properly? check it using a cable tester or replacing with a newone.
As soon as the music gets loud,
the high frequency shuts down
• The HF driver protec on trips to protect the HF driver from excessive signal: turn down the volume and
mid/high tone controls.
Distorted Sound • Input signal level is too high. Turn down your level controls.
Diff erent channel level • Check if are using a balanced cable for one channel and an unbalanced one for the other, as this would
cause a considerable diff erence in channel levels.
• Be sure that your loudspeaker system is fully connected and both loudspeakers have the same
impedance.
Noise / Hum • Enable GND LIFT bu on on rear panel, if the problem persist press all GND LIFT bu ons for all system's
amplifi ers.
• Whenever possible, preferably use only balanced cables. Unbalanced lines may also be used but may result
in noise over long cable runs.
• Some mes it helps to plug all audio equipment into the same AC circuit so they share a common ground.
CE CONFORMITY
• Proel products comply with direc ve 2004/108/EC (EMC), as stated in EN 55103-1 and EN 55103-2 standards and with direc ve 2006/95/CE
(LVD), as stated in EN 60065 standard.
• Under the EM disturbance, the ra o of signal-noise will be changed above 10dB.
PACKAGING, SHIPPING AND COMPLAINT
• This unit package has been submi ed to ISTA 1A integrity tests. We suggest you control the unit condi ons immediately a er unpacking it.
• If any damage is found, immediately advise the dealer. Keep all unit packaging parts to allow inspec on.
• Proel is not responsible for any damage that occurs during shipment.
• Products are sold “delivered ex warehouse” and shipment is at charge and risk of the buyer.
• Possible damages to unit should be immediately no fi ed to forwarder. Each complaint for package tampered with should be done within eight
days from product receipt.
Dura on Per Day
In Hours
Sound Level dBA
Slow Response
Typical
Example
8 90 Duo in small club
692
4 95 Subway Train
397
2 100 Very loud classical music
1.5 102
1 105 Traffi c noise
0.5 110
0.25 or less 115 Loudest parts at a rock concert
9
WARRANTY AND PRODUCTS RETURN
• Proel products have opera ng warranty and comply their specifi ca ons, as stated by manufacturer.
• Proel warrants all materials, workmanship and proper opera on of this product for a period of two years from the original date of purchase. If
any defects are found in the materials or workmanship or if the product fails to func on properly during the applicable warranty period, the owner
should inform about these defects the dealer or the distributor, providing receipt or invoice of date of purchase and defect detailed descrip on.
This warranty does not extend to damage resul ng from improper installa on, misuse, neglect or abuse. Proel S.p.A. will verify damage on returned
units, and when the unit has been properly used and warranty is s ll valid, then the unit will be replaced or repaired. Proel S.p.A. is not responsible
for any "direct damage" or "indirect damage" caused by product defec veness.
INSTALLATION AND DISCLAIMER
• Proel products have been expressly designed for audio applica on, with signals in audio range (20Hz to 20kHz). Proel has no liability for damages
caused in case of lack of maintenance, modifi ca ons, improper use or improper installa on non-applying safety instruc ons.
• The installa on of these speakers is provided for indoors, in case of use outdoors be sure that the speakers are installed correctly in a safe
loca on protected from wind, rain and humidity. To avoid performance deteriora on of mechanical, acous cs and electrical parts is not advisable
to leave these speakers exposed outdoors for a long period of me, so we suggest a temporary installa on for the limited sound events.
• The installa on of these speakers is provided for fl oor or by means of specifi c stands able to support their weight. Therefore avoid installa on
on unstable elements such as: furniture, chairs and vibrant surfaces as stages or other speakers without appropriate fi x point specifi cally designed
to avoid speaker movement. Then avoid the use of inadequate supports, we suggest to use PROEL stands and accessories only.
• In case of the speakers are provided of rigging points: DO NOT SUSPEND THE SPEAKERS FROM THE HANDLES, use exclusively these rigging points.
Consult professional rigger or structural engineers prior to suspending loudspeakers from a structure not intended for that use. Always know the
working load limit of the structure suppor ng the loudspeakers. Always make sure that the rigging hardware minimum ra ng is at least fi ve mes
the actual load, speakers and rigging hardware.
• Locate the speakers as far away as possible from radio or television receivers or other sensi ve equipment. These speakers have a strong
magne c fi eld which can induce hum and noise into unshielded devices that are located nearby with consequent deteriora on of recep on of
image and sound.
• Proel S.p.A. reserves the right to change these specifi ca ons at any me without no ce.
• Proel S.p.A. declines any liability for damages to objects or persons caused by lacks of maintenance, improper use, installa on not performed
with safety precau ons and at the state of the art.
10
GENERAL INFORMATION
Thank you for having chosen a PROEL product.
The WAVE Series by PROEL is a range of speaker systems hosted in lightweight yet ultra-durable polypropylene
cabinets.
The WAVE systems combine selected HF and LF transducers off ering the renowned PROEL sound and a high-level
performance in a reliable and aff ordable lightweight package.
The 3 passive models feature carefully designed crossover fi lters with HF electronic protec on and the built-in fl ying
points make them suitable for also fi xed installa on.
INSTRUCTIONS (FIG. 1 / 2 / 3)
1. INPUT (SPEAKON)
External amplifi er power input: this is the connector where you plug in the power cable coming from your power
amplifi er or powered mixer. The powered signal is fi ltered by an internal passive crossover that splits the power signal
into a low frequency sec on, sent to the woofer, and a high frequency sec on, sent to the HF compression driver. The
frequency transi on is around 2KHz. The INPUT has this pin connec on:
PIN1+ (or TIP): posi ve power signal (usually red wire)
PIN1- (or SLEEVE): nega ve power signal (usually black wire)
2. LINK (SPEAKON)
Output of the power signal to be sent to an another satellite loudspeaker. INPUT and LINK connectors are connected
in parallel.
CHOOSE THE AMPLIFIER POWER
We give you two power-handling numbers: AES or CONTINUOUS, and PEAK. These data suggest you can use any amplifi er
with a power capability equal or less the power-handling, but this rule is valid only if the amplifi er never clips.
Preven ng loudspeaker damage caused by clipping, that is likely the number one cause of damage, and assuming you
want to use the full capability of the loudspeaker, we recommend the use of an amplifi er with a built-in limiter to prevent
clipping: in this case the rated power capability must be the same as the con nuous power ra ng of the loudspeaker
into the same specifi ed impedance ( pically 4 or 8 ohms):
• To obtain the best result using 2 (as single 8 ohm speaker for each channel) to 4 (as parallel 4 ohm speaker for each
channel) WAVE10P connected in stereo, we suggest the use of PROEL HPX-900 amplifi er.
• To obtain the best result using 2 (as single 8 ohm speaker for each channel) to 4 (as parallel 4 ohm speaker for each
channel) WAVE12P connected in stereo, we suggest the use of PROEL HPX-900 or HPX-1200 amplifi er.
• To obtain the best result using 2 (as single 8 ohm speaker for each channel) to 4 (as parallel 4 ohm speaker for each
channel) WAVE15P connected in stereo, we suggest the use of PROEL HPX-1200 amplifi er.
IMPORTANT: Clipping occurs when the signal at the output of any device in the system (not just the amplifi er) reaches its
maximum level. Proper operaƟ on of a sound system includes being aware of the types of audio signals being reproduced,
controlling the output levels accordingly, and operaƟ ng all the devices in the system so that no clipping occurs within
the signal chain.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
REV. 49/14 CODE 96MAN0104
PROEL S.p.A.
(World Headquarter)
Via alla Ruenia 37/43
64027 Sant’Omero (TE) - ITALY
Tel: +39 0861 81241
Fax: +39 0861 887862
www.proel.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
PROEL WAVE12P User manual
- Category
- Audio amplifiers
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- italiano: PROEL WAVE12P Manuale utente
