Anolis Ambiane AP User manual

Category
Stroboscopes & disco lights
Type
User manual

Anolis Ambiane AP is a versatile architectural luminaire that combines high-quality light output with a sleek, minimalist design. With its tunable white light and a wide range of accessories, it's perfect for creating customized lighting solutions for various applications, including retail, hospitality, and museums.

Anolis Ambiane AP is a versatile architectural luminaire that combines high-quality light output with a sleek, minimalist design. With its tunable white light and a wide range of accessories, it's perfect for creating customized lighting solutions for various applications, including retail, hospitality, and museums.

INSTALLATION INSTRUCTIONS
AMBIANE AP
ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: info@anolis.eu | www.anolislighting.com
VERSION 1.0 / 03_2022 1
The unit must be installed by a qualied electrician in accordance with all national and local
electrical and construction codes and regulations.
STEP 1.A
CEILING OPENING - STANDARD MOUNTING HOLE
Prepare mounting hole with diameter between 212-214 mm.
STEP 2
PRIMARY POWER CONNECTION
1A
Install terminal block on power cable (from Ambiane Power Rack or Ambiane Power AP) and connect it to the Primary power connection of
Ambiane AP‘s control unit.
1B
Use of the Adapter ring is recommended in case of a bigger
ceiling opening. See step 6.B before connecting power and
data cables.
STEP 1.B
CEILING OPENING -WITH ADAPTER RING
INSTALLATION INSTRUCTIONS
AMBIANE AP
ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: info@anolis.eu | www.anolislighting.com
VERSION 1.0 / 03_2022 2
STEP 3
DATA CONNECTION (DMX OR DALI)
DMX CONNECTION
0V D- D+
Data Ground Data - Data +
1
2
Set the DIP switches to positions according to your operation
mode. The xture can be controlled by DMX or DALI (switch
11 in OFF position).
STEP 5
DIP SWITCH
1
Unscrew 2 screws on the control unit and remove plastic co-
Install terminal block on power cable for secondary power and
connect it to the Secondary power connection of Ambiane
AP‘s control unit.
STEP 4
SECONDARY POWER CONNECTION 48V
Lift up spring clips on both sides, insert luminaire into ceiling
opening and release spring clips to hold lumaire in place.
STEP 6.A
LUMINAIRE INSTALLATION
Make sure power and data cables are connected
Install terminal blocks on DMX or DALI cables and connect
them to the control unit.
1
INSTALLATION INSTRUCTIONS
AMBIANE AP
ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: inf[email protected] | www.anolislighting.com
VERSION 1.0 / 03_2022 3
1
Lift up springs on both sides, insert luminaire into ceiling ope-
ning and release springs to hold luminaire in place.
STEP 6.B
LUMINAIRE INSTALLATION WITH ADAPTER RING
2
3 4
Slide Adapter ring under the control unit and above both
spring clips. Lift up both springs and slide Adapter ring under them.
Adapter ring installed on the luminaire.
INSTALLATION INSTRUCTIONS
AMBIANE AP
ROBE lighting s. r. o. | Palackeho 416 | 757 01 Valasske Mezirici | Czech Republic | Tel.: +420 571 751 500 | E-mail: inf[email protected] | www.anolislighting.com
VERSION 1.0 / 03_2022 4
Click on Anti-Glare ring.
1
STEP 7
INSTALLTION OF ACCESSORIES - ANTI-GLAR
Insert the Anti-Glare ring into the Ambiane AP‘s reector until
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Anolis Ambiane AP User manual

Category
Stroboscopes & disco lights
Type
User manual

Anolis Ambiane AP is a versatile architectural luminaire that combines high-quality light output with a sleek, minimalist design. With its tunable white light and a wide range of accessories, it's perfect for creating customized lighting solutions for various applications, including retail, hospitality, and museums.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI